mirror of
https://github.com/qmk/qmk_firmware.git
synced 2024-12-26 03:19:54 +00:00
128 lines
4.7 KiB
Markdown
128 lines
4.7 KiB
Markdown
## Unicomp Mini M with Teensy2.0++ controller & QMK Firmware
|
|
|
|
### Overview
|
|
|
|
#### Goals
|
|
|
|
The goal of this project was to replace the stock control board of the Unicomp Mini M with a programmable one. The Mini
|
|
M was released by [Unicomp](https://www.pckeyboard.com) in Q1 of 2021 and is a re-release of The IBM Model M Space
|
|
Saving Keyboard (SSK) with some enhancements.
|
|
|
|
This guide strives to achieve the following:
|
|
|
|
* Make completely reversable changes, or in other words, no permanent modifications to the Mini M
|
|
* Allow full programmability of the Mini M via QMK
|
|
* Be able to flash firmware without having to take the board apart to hit the reset button
|
|
* Create a default keymap that works just like the stock keymap shipped from Unicomp, including the toggle-able number
|
|
pad
|
|
* Support all LEDs as normal
|
|
|
|
My guide will go a few steps further:
|
|
|
|
* Convert the wired connection from USB-A to USB-C
|
|
* Install a potentiometer to dim the LEDs if desired
|
|
|
|
#### Credits
|
|
|
|
The following resources were instrumental to the success of this project:
|
|
|
|
* Model M 101/102 write-up located in `qmk_firmware/keyboards/converter/modelm`
|
|
* [Model M Subreddit](https://modelm.reddit.com)
|
|
* Model M Discord
|
|
|
|
### Hardware
|
|
|
|
##### Parts
|
|
|
|
For a working Mini M with QMK *without* LEDs working, the following parts are necessary:
|
|
|
|
* 1 Adafruit Perma-Proto Full Sized Breadboard. Luckily, this board is a perfect fit for the Mini M case!
|
|
* 1 Teensy2.0++, with headers soldered on if you can find it
|
|
* 2 20-row x 1 column headers, if you can't find a Teensy with headers already soldered on
|
|
* 2 16-pin Ribbon connectors, PCB mount
|
|
* Hookup wire. I used 30AWG wire and while it worked, I should have used 1 gauge (or more) thicker
|
|
* A panel mount male USB-B to female USB-C extender
|
|
|
|
To get the Mini M working with LEDs, you will need:
|
|
|
|
* 3 1kOhm through-hole resistors
|
|
|
|
##### Tools
|
|
|
|
The following were absolutely critical for the project:
|
|
|
|
* Soldering iron, preferably one with a narrow tip for small connections
|
|
* Drill, preferably a hand-held rotary tool (such as a Dremel)
|
|
* Wire strippers/cutters
|
|
* A sharp knife
|
|
|
|
Optional, but worth having around:
|
|
|
|
* Helping-hands, PCB holder, preferably both
|
|
* Multi-meter for testing continuity of your connections
|
|
* Hot-glue gun for mounting the USB extender to the Perma-Proto
|
|
|
|
### Assembly
|
|
|
|
#### Solder Teensy to the Perma-Proto
|
|
|
|
1. Solder headers to Teensy
|
|
2. Solder headers to Perma-Proto
|
|
|
|
#### Solder ribbon connectors
|
|
|
|
* Rows on the Perma-Proto that line up with membrane ribbons
|
|
* Trim excess under board
|
|
* Test continuity
|
|
|
|
#### Solder in hookup wires
|
|
|
|
* Ribbon connector used for the right ribbon will need hookup wire to establish connections to the Teensy
|
|
* 12 required, 16 if you want full functionality
|
|
|
|
#### Optional: Solder in resistors
|
|
|
|
#### Caveat: D6 pin on the Teensy
|
|
|
|
There are a few ways to mount the Teensy to the Perma-Proto board. I chose to connect my 16 pin ribbon connector to the
|
|
Teensy pins starting at C7 and ending at D2. If you do this, beware that pin D6 will not work for the purposes of this
|
|
project. It is possible to modify it to make it so, but that is beyond the scope of this guide.
|
|
|
|
Bypassing D6 is necessary if you mount your ribbon connector as I have just described. Luckily, it is a simple process!
|
|
First, with a sharp knife, sever the connection between your ribbon connector pin that is connected to Teensy D6 pin. I
|
|
would recommend doing this at the closest possible point to the Teensy on the underside of the Perma-Proto board. Once
|
|
that is done, use a remaining point on the Perma-Proto bus for that ribbon connection (that was previously connected to
|
|
D6) to add a jumper wire connected to pin B7. If you are using the firmware files provided in this repository,
|
|
everything is already set for this configuration.
|
|
|
|
### Testing
|
|
|
|
### Software
|
|
|
|
#### Build firmware
|
|
|
|
See qmk documentation on getting your build environment working.
|
|
|
|
Compile the Mini M firmware files with the default keymap. It allows for the Mini M to be used with the same
|
|
functionality as shipped from the manufacturer.
|
|
|
|
```bash
|
|
$ qmk compile -kb unicomp/mini_m -km default
|
|
```
|
|
|
|
While plugged in, press the reset button on your Teensy and then:
|
|
|
|
```bash
|
|
$ qmk flash -kb unicomp/mini_m -km default
|
|
```
|
|
|
|
If everything works to this point, congratulations! You now have a programmable Mini M. If you are using the default
|
|
keymap, you can reset your Teensy by pressing Shift+Pause together, eliminating the need to take apart the case in order
|
|
to do so.
|
|
|
|
#### Keymaps
|
|
|
|
To build your own keymap, create a new directory in `keyboards/unicomp/mini_m/keymaps/<your name>`, copy the files from
|
|
`keyboards/unicomp/mini_m/default` into your new directory, and edit them as you wish. When you are ready to flash your
|
|
new keymap to the Mini M, the command will be `qmk flash -kb unicomp/mini_m -kb <your name>`.
|