mirror of
https://github.com/qmk/qmk_firmware.git
synced 2024-12-04 00:45:13 +00:00
c8237a7691
Co-authored-by: Joel Challis <git@zvecr.com> Co-authored-by: Drashna Jaelre <drashna@live.com> Co-authored-by: jack <0x6a73@protonmail.com>
49 lines
2.1 KiB
Markdown
49 lines
2.1 KiB
Markdown
# QMK-based firmware for Sejin EAT-1010R2 keyboard
|
||
|
||
* Keyboard Maintainer: [DmNosachev](https://github.com/DmNosachev)
|
||
* Hardware Supported: Sejin EAT-1010R2 (membrane keyboard, Sejin
|
||
Futaba-mount dome, Asian 101 ISO layout), Blue/Black Pill STM32F103 MCU
|
||
oard. Alternatevely you can use any MCU which is supported by QMK and
|
||
has 27 or more IO pins
|
||
|
||
Make example for this keyboard (after setting up your build environment):
|
||
|
||
make handwired/sejin_eat1010r2:default
|
||
|
||
Flashing example for this keyboard:
|
||
|
||
make handwired/sejin_eat1010r2:default:flash
|
||
|
||
|
||
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools)
|
||
and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide)
|
||
for more information. Brand new to QMK? Start with our
|
||
[Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
|
||
|
||
## Additional hardware
|
||
* 16 and 8 pin 2.54mm (0.1'') FPC connectors. They can be found at
|
||
Aliexpress for 2–3 USD for 10pcs. Two 8 pin connectors can be glued
|
||
together as a replacement for 16 pin.
|
||
* Three 5mm LEDs and current limiting resistors (150–300Ω, depending on
|
||
LED specs). This keyboard has exactly the same spacing between LEDs as
|
||
IBM Model M, so a corresponding PCB can be used after adding resistors.
|
||
|
||
## Membrane
|
||
Sejin EAT-1010R2 has 16x8 matrix. There are 16 and 8 pin flex connectors
|
||
from membrane sheets. Solder FPC connectors to devboard (numbering from
|
||
left to right, see *matrix_pins* in info.json file).
|
||
|
||
## Bootloader
|
||
Burn [STM32duino bootloader](https://github.com/rogerclarkmelbourne/STM32duino-bootloader)
|
||
to Blue Pill board.
|
||
|
||
There are several ways to get into the bootloader:
|
||
* STM32duino bootloader waits for 3 seconds in DFU mode before jumping to application.
|
||
You just have to start the flashing process, then connect the USB.
|
||
* This firmware is configured with [bootmagic feature](https://docs.qmk.fm/#/feature_bootmagic).
|
||
Hold the ESC key down when plugging the keyboard in to trigger the bootloader.
|
||
|
||
## Troubleshooting
|
||
There is *debug* layout which has mapping for every matrix position and
|
||
prints column and raw numbers to console (hid_listen or QMK toolbox).
|