* Fix DEBUG_MATRIX_SCAN_RATE on chibiOS when console is enabled
* update type in dprintf
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* resolve race condition between suspend and wake in LUFA
* avoid multiple calls to suspend_power_down() / suspend_wakeup_init()
* Remove duplicate suspend_power_down_kb() call
* pause on wakeup to wait for USB state to settle
* need the repeated suspend_power_down() (that's where the sleep is)
* more efficient implementation
* fine tune the pause after sending wakeup
* speculative chibios version of pause-after-wake
* make wakeup delay configurable, and adjust value
* better location for wakeup delay
* Add support for 8 buttons to mouse report
This includes support for 8 buttons in mousekeys. However, this does move the keys around due to the fact that the last mousekey keycode is already 0xFF, so any past that would not work with register_code and the like, breaking them for tap hold keys, encoders, and other features.
* Update mouse key docs
* Add changes based on feedback
* Fix VUSB report size comment
Because drashna red gud
* Fix typo in action.c
* Fix IS_MOUSE_BUTTON check
* Change start range for mousekeys so that the end is 0xFF properly
* condense mousekeys check
* fix matrix_io_delay() timing in quantum/matrix.c
* Updated comments explaining the need for matrix_io_delay() in quantum/matrix.c
* fix matrix_io_delay() timing in quantum/split_common/matrix.c
* Update quantum/matrix.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update quantum/split_common/matrix.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update quantum/matrix.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update quantum/split_common/matrix.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* add waitOutputPinValid() and wait_cpuclock() into quantum/quantum.h and tmk_core/common/wait.h
* add matrix_output_select_delay() and matrix_output_unselect_delay()
* fix quantum/matrix_common.c, tmk_core/common/matrix.h
* fix tmk_core/common/wait.h
* fix quantum/quantum.h, tmk_core/common/wait.h
* waitOutputPinValid() rename to waitInputPinDelay() in quantum/quantum.h.
* waitOutputPinValid() rename to waitInputPinDelay() in quantum/matrix_common.c
* update tmk_core/common/wait.h
* update comment in quantum/matrix.c, quantum/split_common/matrix.c
* update quantum/quantum.h: Make more margin in the GPIO_INPUT_PIN_DELAY default value.
Co-authored-by: Ryan <fauxpark@gmail.com>
* Allow recording of the last matrix activity time, to simplify implementation of display timeouts and the like.
* Add requested changes from code review.
* Simplify split matrix last changed.
* Add proper prototypes for Tap-Hold Per Key functions
* Fix handwired/tennie default keymap
* Remove unneeded references
* Fix tapping term per key check in space cadet
* Pre-emptive fix for tap dance
* Fix marksard/leftover30
* Replace hard coded tapping term with define
* Add target 'build-for-compare' to `build_keyboard.mk`
The `build-for-compare` target provides an easy way to check the md5 checksum of the generated binary.
You can easily see if there is any change in the generated binaries between the two versions, as in the example below.
```
$ git checkout 0.11.0
M build_keyboard.mk
M tmk_core/rules.mk
Note: checking out '0.11.0'.
HEAD is now at c66df1664 2020 November 28 Breaking Changes Update (#11053)
$ make helix:all:build-for-compare | grep ^MD5
MD5 (.build/helix_rev2_default.hex) = 5c3606562c944bb4d18832e601b45d4a
MD5 (.build/helix_rev2_edvorakjp.hex) = 9e43d13d389d518ba7e99cd7337e28d6
MD5 (.build/helix_rev2_five_rows.hex) = 8bcb61c2fd5d237c2997f2fa007d4934
MD5 (.build/helix_rev2_five_rows_jis.hex) = b97cd818d52f73ca2d4e78c86d90a791
MD5 (.build/helix_rev2_froggy.hex) = c492172364188f4e2918b10bf0f3a0a6
MD5 (.build/helix_rev2_froggy_106.hex) = b0861fd735a8f81881a8c02730641a2b
MD5 (.build/helix_rev2_led_test.hex) = 5c97d982a5da5cfb3dacb28a8934b81d
MD5 (.build/helix_rev2_xulkal.hex) = 01f603dc46bcf9094d7e106831d8f5b1
MD5 (.build/helix_rev2_yshrsmz.hex) = 5a008bca2d0c5790a151c02834c529ba
$ git checkout 0.11.1
M build_keyboard.mk
M tmk_core/rules.mk
Previous HEAD position was c66df1664 2020 November 28 Breaking Changes Update (#11053)
HEAD is now at cc08e3082 nix-shell: add milc dependency (#11086)
$ make helix:all:build-for-compare | grep ^MD5
MD5 (.build/helix_rev2_default.hex) = 5c3606562c944bb4d18832e601b45d4a
MD5 (.build/helix_rev2_edvorakjp.hex) = 9e43d13d389d518ba7e99cd7337e28d6
MD5 (.build/helix_rev2_five_rows.hex) = 8bcb61c2fd5d237c2997f2fa007d4934
MD5 (.build/helix_rev2_five_rows_jis.hex) = b97cd818d52f73ca2d4e78c86d90a791
MD5 (.build/helix_rev2_froggy.hex) = c492172364188f4e2918b10bf0f3a0a6
MD5 (.build/helix_rev2_froggy_106.hex) = b0861fd735a8f81881a8c02730641a2b
MD5 (.build/helix_rev2_led_test.hex) = 5c97d982a5da5cfb3dacb28a8934b81d
MD5 (.build/helix_rev2_xulkal.hex) = d848383adfd7463b138c6da179cf1436
MD5 (.build/helix_rev2_yshrsmz.hex) = 5a008bca2d0c5790a151c02834c529ba
```
* make builds reproducable by default
* update build_keyboard.mk: remove 'build-for-compare' target
* GNU make (3.81) on macOS 10.14(Mojave) does not have the 'undefine' directive.
* Adopted fauxpark's suggestion.
* Update tmk_core/rules.mk
Co-authored-by: Ryan <fauxpark@gmail.com>
* update tmk_core/rules.mk
* fix tmk_core/rules.mk
Co-authored-by: Zach White <skullydazed@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update ADB impelmentation in tmk_core to recent version.
Pcked from tmk_keyboard repository revision: 48d696443857512d45f9a7329e0dd0a76345860f
* Restore convenient ADB functions used in QMK port.
* Do cformat.
* Split dmac_desc declaration and definition
According to the official documentation[1] gcc 10 is more strict about
correct extern usage.
I've had to move the definition of dmac_desc and dmac_desc_wb from
i2c_master.h to the corresponding .c file. This could be an issue if
anyone includes the i2c_master.h file without liking with the object
file.
[1]: https://gcc.gnu.org/gcc-10/porting_to.html
* Remove the keymap_config definition from keymaps
The keymap_config def was conflicting with the one found in
tmk_core/common/magic.c. Declaring it extern in magic.c breaks a bunch
of keyboard that rely on that declaration (like the ergodox). Instead
I've removed the one found in the keymap.c of the massdrop alt.
The same change will have to be made to other keyboards.
- Set all other ChibiOS defaults to 'off', when not targeting Proton-C
- Modified all existing F303 boards to point at the QMK_PROTON_C to ensure repeatable binary output
- Modified version.h generation so that SKIP_VERSION=yes generates the same output
* Branch point for 2020 November 28 Breaking Change
* Remove matrix_col_t to allow MATRIX_ROWS > 32 (#10183)
* Add support for soft serial to ATmega32U2 (#10204)
* Change MIDI velocity implementation to allow direct control of velocity value (#9940)
* Add ability to build a subset of all keyboards based on platform.
* Actually use eeprom_driver_init().
* Make bootloader_jump weak for ChibiOS. (#10417)
* Joystick 16-bit support (#10439)
* Per-encoder resolutions (#10259)
* Share button state from mousekey to pointing_device (#10179)
* Add hotfix for chibios keyboards not wake (#10088)
* Add advanced/efficient RGB Matrix Indicators (#8564)
* Naming change.
* Support for STM32 GPIOF,G,H,I,J,K (#10206)
* Add milc as a dependency and remove the installed milc (#10563)
* ChibiOS upgrade: early init conversions (#10214)
* ChibiOS upgrade: configuration file migrator (#9952)
* Haptic and solenoid cleanup (#9700)
* XD75 cleanup (#10524)
* OLED display update interval support (#10388)
* Add definition based on currently-selected serial driver. (#10716)
* New feature: Retro Tapping per key (#10622)
* Allow for modification of output RGB values when using rgblight/rgb_matrix. (#10638)
* Add housekeeping task callbacks so that keyboards/keymaps are capable of executing code for each main loop iteration. (#10530)
* Rescale both ChibiOS and AVR backlighting.
* Reduce Helix keyboard build variation (#8669)
* Minor change to behavior allowing display updates to continue between task ticks (#10750)
* Some GPIO manipulations in matrix.c change to atomic. (#10491)
* qmk cformat (#10767)
* [Keyboard] Update the Speedo firmware for v3.0 (#10657)
* Maartenwut/Maarten namechange to evyd13/Evy (#10274)
* [quantum] combine repeated lines of code (#10837)
* Add step sequencer feature (#9703)
* aeboards/ext65 refactor (#10820)
* Refactor xelus/dawn60 for Rev2 later (#10584)
* add DEBUG_MATRIX_SCAN_RATE_ENABLE to common_features.mk (#10824)
* [Core] Added `add_oneshot_mods` & `del_oneshot_mods` (#10549)
* update chibios os usb for the otg driver (#8893)
* Remove HD44780 References, Part 4 (#10735)
* [Keyboard] Add Valor FRL TKL (+refactor) (#10512)
* Fix cursor position bug in oled_write_raw functions (#10800)
* Fixup version.h writing when using SKIP_VERSION=yes (#10972)
* Allow for certain code in the codebase assuming length of string. (#10974)
* Add AT90USB support for serial.c (#10706)
* Auto shift: support repeats and early registration (#9826)
* Rename ledmatrix.h to match .c file (#7949)
* Split RGB_MATRIX_ENABLE into _ENABLE and _DRIVER (#10231)
* Split LED_MATRIX_ENABLE into _ENABLE and _DRIVER (#10840)
* Merge point for 2020 Nov 28 Breaking Change
* Update massdrop/alt keyboard to fix Caps Lock LED flickering.
* Fix Caps-lock LED during underglow-only for massdrop/ctrl
* Update keyboards/massdrop/ctrl/keymaps/default/keymap.c
* First pass
* Add config options to docs
* Update some wording
* Slight tidy up of backlight caps logic
* Init pin to correct state
* Move init location
* Reverse default state
The `KEYBOARD_SHARED_EP=yes` option was breaking the VIA support,
because the raw HID interface number in this case was 0 instead of 1,
and the VIA app depends on the exact interface number for raw HID.
Change the interface ordering to put the shared interface before the raw
HID interface if `KEYBOARD_SHARED_EP` is enabled, so that the raw HID
interface can keep its number.
* Output an error message if LINK_TIME_OPTIMIZATION_ENABLE is set but LTO_ENABLE is not.
* Update common.mk
Specify that LINK_TIME_OPTIMZATION_ENABLE has been renamed, not deprecated.
* Better handle LTO_ENABLE
Especially when calling from command line
* Replace LINK_TIME_OPTIMIZATION_ENABLE with LTO_ENABLE
* Remove long for LTO from show_options.mk
* Update vusb to match 3rd endpoint.
- With the addition of https://github.com/qmk/v-usb/pull/1 a 3rd endpoint (endpoint4) becomes available.
- We can assign mouse/extrakeys to that endpoint as its a desirable feature and leave rawhid and console to compete for the 2nd endpoint.
NOTE: The version of vusb.c in future branch is older than master. Just remember that it will need a #error if both raw_hid and console are enabled at the same time.
* Final Fixes
* Update tmk_core/protocol/vusb/vusb.c
* Update tmk_core/protocol/vusb/vusb.c
* Update tmk_core/protocol/vusb/usbconfig.h
* Update tmk_core/protocol/vusb/usbconfig.h
* Update tmk_core/protocol/vusb/usbconfig.h
* Update tmk_core/protocol/vusb/usbconfig.h
* Updated vusb submodule to latest commit
* Add `st-flash` flash target
Add support for flashing the firmware via the `st-flash` utility from
the STLink Tools package (https://github.com/stlink-org/stlink).
* Add `st-flash` to the `qmk flash -b` output
* Initialize Layer State on startup
Right now, on startup, the default layer state gets called and set, triggering the callback functions for the default layer state. However, the normal layer state never actually gets initialized. It's set to 0 directly, by default, but the callback functions are never actually called. This creates some inconsistency in the behavior for end users. This adds a simple "clear" that triggers the callback on startup. This should produce more consisten behavior between the two functions and layer masks.
* Stupid hack
* Fix type casting?
* Fix compile issues with magic is disabled
* add support for hid gamepad interface
add documentation for HID joystick
Add joystick_task to read analog axes values even when no key is pressed or release. update doc
Update docs/feature_joystick.md
Manage pin setup and read to maintain matrix scan after analog read
* Incorporates patches and changes to HID reporting
There are some patches provided by @a-chol incorporated on this commit,
and also some changes I made to the HID Report structure.
The most interesting is the one dealing with number of buttons: Linux
doesn't seem to care, but Windows requires the HID structure to be byte
aligned (that's in the spec). So if one declares 8/16/32... buttons they
should not have any issues, but this is what happens when you have 9
buttons:
```
bits |0|1|2|3|4|5|6|7|
|*|*|*|*|*|*|*|*| axis 0 (report size 8)
|*|*|*|*|*|*|*|*| ...
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*| axis 6
|*|*|*|*|*|*|*|*| first 8 buttons (report size 1)
|*| | | | | | | | last of 9 buttons, not aligned
```
So for that I added a conditonal that will add a number of reports with
size 1 to make sure it aligns to the next multiple of 8. Those reports
send dummy inputs that don't do anything aside from aligning the data.
Tested on Linux, Windows 10 and Street Fighter (where the joystick is
recognized as direct-input)
* Add save and restore of each pin used in reading joystick (AVR).
Allow output pin to be JS_VIRTUAL_AXIS if the axis is connected to Vcc
instead of an output pin from the MCU.
Fix joystick report id
Fix broken v-usb hid joystick interface. Make it more resilient to unusual settings (none multiple of eight button count, 0 buttons or 0 axes)
Correct adc reading for multiple axes. Piecewise range conversion for uncentered raw value range. Input, output and ground pin configuration per axis.
Documentation fixes
* Fix port addressing for joystick analog read
* The other required set of changes
As per the PR, the changes still holding it up.
Add onekey for testing.
Fix ARM builds.
Fix device descriptor when either axes or buttons is zero.
Add compile-time check for at least one axis or button.
Move definition to try to fix conflict.
PR review comments.
qmk cformat
* avoid float functions to compute range mapping for axis adc reading
* Remove V-USB support for now. Updated docs accordingly.
* Update tmk_core/protocol/lufa/lufa.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add support for joystick adc reading for stm32 MCUs. Fix joystick hid report sending for chibios
* Fix HID joystick report sending for ChibiOS.
Add one analog axis to the onekey:joystick keymap.
Fix pin state save and restore during joystick analog read for STM32
MCUs.
* Update tmk_core/protocol/chibios/usb_main.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/lufa/lufa.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add missing mcuconf.h and halconf.h to onekey:joystick keymap.
Add suggested fixes from PR.
* Switch saveState and restoreState signature to use pin_t type.
onekey:joystick : add a second axis, virtual and programmatically animated.
* Update docs/feature_joystick.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update docs/feature_joystick.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add PR corrections
* Remove halconf.h and mcuconf.h from onekey keymaps
* Change ADC_PIN to A0
Co-authored-by: achol <allecooll@hotmail.com>
Co-authored-by: José Júnior <jose.junior@gmail.com>
Co-authored-by: a-chol <achol@notamail.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Disable NKRO on V-USB controllers
* not _currently_ supported text
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Re-fix the dual-bank bootloader stuff.
* Use wait_ms() instead of using nop's for a delay, as ChibiOS is actually running at the time of bootloader jump.
Mousekey scrolling should have a separate repeat variable
to keep track of scrolling acceleration, instead of being
tied to mouse movement scolling in mousekeys. The send function
should record when the last movement was made since this is
when movement is actually sent. Doing this fixes the bug where
the initial press of a mousekey scroll button causes a double scroll.
Signed-off-by: Daniel Hong <daniel.hong@live.com>
* Initial work for consolidation of board files and default ChibiOS configs.
* Migrate F401/F411 black pills for testing.
* Add early init bootloader jump flag.
* Add support for I2C in order to use i2c_scanner keymap.
* Add F401/F411 HSE bypass to get things booting.
* Exempt "hooked" ChibiOS conf files from updater script.
* Fix up ordering for bootloader_defs file check.
* Match previous $(KEYBOARD_PATHS) value for Proton-C, updated for all board configs.
Fixes the handling for the oneshot cleanup, so it only cleans up if it is active. It should not cleanup of SHO is off (eg using a normal oneshot key), nor if it's actively pressed or used.
Previous behavior BROKE swap hand key.
* I2C_TIMEOUT is not defined on arm teensy
* Work round teensy having different ChibiOS config options
* Stash OLED conf files
* update comment
* update comment
* Remove stm32 alias to allow teensy alt mode
Process mouse movement in the keymap before it is sent to the host. Example uses
include filtering noise, adding acceleration, and automatically activating a
layer. To use, define the following function in your keymap:
void ps2_mouse_moved_user(report_mouse_t *mouse_report);
With this change, when ps2_mouse is disabled, mousekeys works as usual. With
ps2_mouse enabled, mousekeys button state is shared with ps2_mouse for clicking,
dragging, and scrolling, mousekeys clicks are produced by ps2_mouse only, and
mouskeys button state is transferred to mousekeys without generating clicks to
enable mousekeys dragging.
Co-authored-by: Drashna Jaelre <drashna@live.com>
Co-authored-by: Drashna Jaelre <drashna@live.com>
* init
* add RETRO_TAP; tap anyway after TAP_TERM, if no interruption
* RETRO_TAP works for other types of taps
* revert to upstream/master
* explain this fork in readme
* use one readme.md file instaed
* fix the error if NO_ACTION_ONESHOT is defined
* restore readme.md to upstream master
Co-authored-by: Tsan-Kuang Lee <tsan.kuang.lee@gmail.com>
* Branch point for 2020 May 30 Breaking Change
* Migrate `ACTION_LAYER_TOGGLE` to `TG()` (#8954)
* Migrate `ACTION_MODS_ONESHOT` to `OSM()` (#8957)
* Migrate `ACTION_DEFAULT_LAYER_SET` to `DF()` (#8958)
* Migrate `ACTION_LAYER_MODS` to `LM()` (#8959)
* Migrate `ACTION_MODS_TAP_KEY` to `MT()` (#8968)
* Convert V-USB usbdrv to a submodule (#8321)
* Unify Tap Hold functions and documentation (#8348)
* Changing board names to prevent confusion (#8412)
* Move the Keyboardio Model01 to a keyboardio/ subdir (#8499)
* Move spaceman keyboards (#8830)
* Migrate miscellaneous `fn_actions` entries (#8977)
* Migrate `ACTION_MODS_KEY` to chained mod keycodes (#8979)
* Organizing my keyboards (plaid, tartan, ergoinu) (#8537)
* Refactor Lily58 to use split_common (#6260)
* Refactor zinc to use split_common (#7114)
* Add a message if bin/qmk doesn't work (#9000)
* Fix conflicting types for 'tfp_printf' (#8269)
* Fixed RGB_DISABLE_AFTER_TIMEOUT to be seconds based & small internals cleanup (#6480)
* Refactor and updates to TKC1800 code (#8472)
* Switch to qmk forks for everything (#9019)
* audio refactor: replace deprecated PLAY_NOTE_ARRAY (#8484)
* Audio enable corrections (2/3) (#8903)
* Split HHKB to ANSI and JP layouts and Add VIA support for each (#8582)
* Audio enable corrections (Part 4) (#8974)
* Fix typo from PR7114 (#9171)
* Augment future branch Changelogs (#8978)
* Revert "Branch point for 2020 May 30 Breaking Change"
This commits add the SH_OS keycode, which works similarly to one shot
layers:
* while pressed, the keyboard is swapped
* if no keys were pressed while it was pressed, the next key press is
swapped
SH_OS also supports chaining with one shot layers:
OSL(x) + SH_OS + key interprets the key press on the oneshot layer.
The ONESHOT_TIMEOUT setting used by one shot keys and layers is also
used by oneshot swap hands. In the above chaining scenario the timeout
of the oneshot layer is reset when swap hands is activated.
Resolves#2682
* Improve security by eliminating the use of well-known names.
* Add an additional $ so the shell expands $TMP1 and $TMP2
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Refactor to use mpaland/printf
* trim firmware size
* remove keymap changes
* run clang format
* Fixup after rebase
* fix up git-submodule command for printf
* Add support for hardware and board initialisation overrides.
* qmk cformat.
* Add some documentation.
* Docs clarity.
* Make early_hardware_init_pre a no-op for now, until migrations occur.
* Doco update
* Make distinction between keyboard and ChibiOS board in docs
* Doc anchors.
* Update tmk_core/protocol/chibios/main.c
Co-Authored-By: Joel Challis <git@zvecr.com>
* Rework bootloader entry to be off by default, allow opting-in.
Co-authored-by: Joel Challis <git@zvecr.com>
* tmk_core/common: Fixing TIMER_DIFF macro to calculate difference correctly after the timer wraps.
Let's go through an example, using the following macro:
If the first timer read is 0xe4 and the second one is 0x32, the timer wrapped.
If the timer would have had more bits, it's new value would have been 0x132,
and the correct difference in time is 0x132 - 0xe4 = 0x4e
old code TIMER_DIFF_8(0x32, 0xe4) = 0xff - 0xe4 + 0x32 = 0x4d, which is wrong.
new code TIMER_DIFF_8(0x32, 0xe4) = 0xff + 1 - 0xe4 + 0x32 = 0x4e, which is correct.
This also gives a chance for a smart compiler to optimize the code using normal
integer overflow.
For example on AVR, the following C code:
uint8_t __attribute__ ((noinline)) test(uint8_t current_timer, uint8_t start_timer)
{
return TIMER_DIFF_8(current_timer, start_timer);
}
With the original code, it gets translated to the following list of instructions:
00004c6e <test>:
4c6e: 98 2f mov r25, r24
4c70: 86 1b sub r24, r22
4c72: 96 17 cp r25, r22
4c74: 08 f4 brcc .+2 ; 0x4c78 <test+0xa>
4c76: 81 50 subi r24, 0x01 ; 1
4c78: 08 95 ret
But with this commit, it gets translated to a single instruction:
00004c40 <test>:
4c40: 86 1b sub r24, r22
4c42: 08 95 ret
This unfortunately doesn't always work so nicely, for example the following C code:
int __attribute__ ((noinline)) test(uint8_t current_timer, uint8_t start_timer)
{
return TIMER_DIFF_8(current_timer, start_timer);
}
(Note: return type changed to int)
With the original code it gets translated to:
00004c6e <test>:
4c6e: 28 2f mov r18, r24
4c70: 30 e0 ldi r19, 0x00 ; 0
4c72: 46 2f mov r20, r22
4c74: 50 e0 ldi r21, 0x00 ; 0
4c76: 86 17 cp r24, r22
4c78: 20 f0 brcs .+8 ; 0x4c82 <test+0x14>
4c7a: c9 01 movw r24, r18
4c7c: 84 1b sub r24, r20
4c7e: 95 0b sbc r25, r21
4c80: 08 95 ret
4c82: c9 01 movw r24, r18
4c84: 84 1b sub r24, r20
4c86: 95 0b sbc r25, r21
4c88: 81 50 subi r24, 0x01 ; 1
4c8a: 9f 4f sbci r25, 0xFF ; 255
4c8c: 08 95 ret
Wth this commit it gets translated to:
00004c40 <test>:
4c40: 28 2f mov r18, r24
4c42: 30 e0 ldi r19, 0x00 ; 0
4c44: 46 2f mov r20, r22
4c46: 50 e0 ldi r21, 0x00 ; 0
4c48: 86 17 cp r24, r22
4c4a: 20 f0 brcs .+8 ; 0x4c54 <test+0x14>
4c4c: c9 01 movw r24, r18
4c4e: 84 1b sub r24, r20
4c50: 95 0b sbc r25, r21
4c52: 08 95 ret
4c54: c9 01 movw r24, r18
4c56: 84 1b sub r24, r20
4c58: 95 0b sbc r25, r21
4c5a: 93 95 inc r25
4c5c: 08 95 ret
There is not much performance improvement in this case, however at least with this
commit it functions correctly.
Note: The following commit will improve compiler output for the latter example.
* tmk_core/common: Improve code generation for TIMER_DIFF* macros
Because of integer promotion the compiler is having a hard time generating
efficient code to calculate TIMER_DIFF* macros in some situations.
In the below example, the return value is "int", and this is causing the
trouble.
Example C code:
int __attribute__ ((noinline)) test(uint8_t current_timer, uint8_t start_timer)
{
return TIMER_DIFF_8(current_timer, start_timer);
}
BEFORE: (with -Os)
00004c40 <test>:
4c40: 28 2f mov r18, r24
4c42: 30 e0 ldi r19, 0x00 ; 0
4c44: 46 2f mov r20, r22
4c46: 50 e0 ldi r21, 0x00 ; 0
4c48: 86 17 cp r24, r22
4c4a: 20 f0 brcs .+8 ; 0x4c54 <test+0x14>
4c4c: c9 01 movw r24, r18
4c4e: 84 1b sub r24, r20
4c50: 95 0b sbc r25, r21
4c52: 08 95 ret
4c54: c9 01 movw r24, r18
4c56: 84 1b sub r24, r20
4c58: 95 0b sbc r25, r21
4c5a: 93 95 inc r25
4c5c: 08 95 ret
AFTER: (with -Os)
00004c40 <test>:
4c40: 86 1b sub r24, r22
4c42: 90 e0 ldi r25, 0x00 ; 0
4c44: 08 95 ret
Note: the example is showing -Os but improvements can be seen at all optimization levels,
including -O0. We never use -O0, but I tested it to make sure that no extra code is
generated in that case.OA
* quantum/debounce: Fix custom wrapping timers in eager_pr and eager_pk debounce algorithms
Please see the below simulated sequence of events:
Column A is the 16-bit value returned by read_timer();
Column B is the value returned by custom_wrap_timer_read();
Column C is the original code: (timer_read() % MAX_DEBOUNCE)
A, B, C
65530, 19, 30
65531, 20, 31
65532, 21, 32
65533, 22, 33
65534, 23, 34
65535, 24, 35
0 25, 0
1, 26, 1
2, 27, 2
3, 28, 3
4, 29, 4
5, 30, 5
read_timer() wraps about every 1.09 seconds, and so debouncing might
fail at these times without this commit.
* quantum/debounce/eager_pr and eager_pk: modifications for code readability according to code review.
* quantum/debounce/eager_pr and eager_pk: modifications for code readability according to code review. (2)
* Add PS2_MOUSE_ROTATE to compensate for device orientation
* fixup! Add PS2_MOUSE_ROTATE to compensate for device orientation
* Reformat with IndentPPDirectives: AfterHash as per #6316
* Define NO_ACTION_MACRO/FUNCTION in header instead of makefile when LTO is enabled
Currently, boards and keymaps that define NO_ACTION_MACRO/FUNCTION unconditionally
will not compile with LTO_ENABLE (#8604). This fixes the issue by moving the
definitions from common.mk to action.h, which enables us to check for previous
definitions of those macros (this cannot be done in a makefile).
* Remove LTO checks in templates
Since now NO_ACTION_MACRO/FUNCTION are defined as needed in action.h (which is
included by quantum.h), checking for LTO in keyboard and user code is no
longer required.
* Update LTO_ENABLE docs
* Change _delay_ms/us() to wait_ms/us()
* Switch to platform-agnostic GPIO macros
* Add AVR spi_master and migrate Adafruit BLE code
* Set verbose back to false
* Add clock divisor, bit order and SPI mode configuration for init
* Add start and stop functions
* Move configuration of mode, endianness and speed to `spi_start()`
* Some breaks here would be good
* Default Adafruit BLE clock divisor to 4 (2MHz on the Feather 32U4)
* Remove mode and divisor enums
* Add some docs
* No hr at EOF
* Add links in sidebar
* rewrite usbhid feature on vusb
* Apply suggestions from code review
Co-Authored-By: Ryan <fauxpark@gmail.com>
* fix typo
* fix typo again
* Update tmk_core/protocol/vusb/vusb.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* clean up defines
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update tmk_core/common/progmem.h
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update quantum/rgblight.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* fixed problem with implicit declaration in quantum/rgblight.c (#8381)
Co-authored-by: Ryan <fauxpark@gmail.com>
* Port over some AVR backlight logic to SLEEP_LED
* Port over some AVR backlight logic to SLEEP_LED - add timer 3
* Port over some AVR backlight logic to SLEEP_LED - clang format
* Enable SLEEP_LED within vusb protocol
* Add support for RAW endpoint for arm_atsam
This the excellent work from helluvamatt/qmk_firmware in bb6eeb93b.
* Reformat arm_atsam RAW endpoint code
Co-authored-by: Matt Schneeberger <helluvamatt@gmail.com>
* Improve process_record system
Code based on @colinta's
* Rename and better handle functions
* Fix incorrect function call to process_record_user
* Add documentation for post_process_record
* Add both get_event_keycode and get_record_keycode functions
And add some comments about these functions
* Update code format
* Cleanup merge artifacts
* Add support for Bootmagic lite when using SPLIT_HAND_PIN
* Deduplicate bootmagic_lite logic from within via
* Revert location of defaults so that user overrides still work for now
* Tidy up code slightly
* Remove unnecessary import of rgblight.h in tmk_core/protocol/*/*.c
* tmk_core/protocol/chibios/main.c
* tmk_core/protocol/lufa/lufa.c
see #8380 for tmk_core/protocol/vusb/main.c.
* Remove '#include "rgblight.h"' from tmk_core/protocol/vusb/main.c.
* Fix extra keyboard report during test_fixture teardown
* Add tests for pressing two keys with only different modifers
* Fix#1708
When two keys that use the same keycode, but different modifiers were
pressed at the same time, the second keypress wasn't registered. This is
fixed by forcing a key release when we detect a new press for the same
keycode.
* Fix the NKRO version of is_key_pressed
* Fix uninitalized loop variable
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* Moved contents of rgblight_reconfig.h to rgblight_post_config.h.
In #3582, rgblight_reconfig.h had to be newly created. Now, the build system of qmk_firmware has a post_cofig feature, so that what was done in rgblight_reconfig.h can now be realized in rgblight_post_config.h.
**This commit does not change the build result.**
Testing script
```shell
# build on master
git checkout master
echo master > /tmp/master_md5.txt
# RGBLIGHT_ENABLE = no
make HELIX=verbose helix/rev2:default:clean
make HELIX=verbose helix/rev2:default
md5 helix_rev2_default.hex >> /tmp/master_md5.txt
# RGBLIGHT_ENABLE = yes, with animations
make HELIX=verbose helix/rev2/back:default:clean
make HELIX=verbose helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/master_md5.txt
# RGBLIGHT_ENABLE = yes, without animations
make HELIX=verbose,no_ani helix/rev2/back:default:clean
make HELIX=verbose,no_ani helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/master_md5.txt
# build on refactor_rgblight_reconfig.h
git checkout refactor_rgblight_reconfig.h
echo refactor_rgblight_reconfig.h > /tmp/branch_md5.txt
# RGBLIGHT_ENABLE = no
make HELIX=verbose helix/rev2:default:clean
make HELIX=verbose helix/rev2:default
md5 helix_rev2_default.hex >> /tmp/branch_md5.txt
# RGBLIGHT_ENABLE = yes, with animations
make HELIX=verbose helix/rev2/back:default:clean
make HELIX=verbose helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/branch_md5.txt
# RGBLIGHT_ENABLE = yes, without animations
make HELIX=verbose,no_ani helix/rev2/back:default:clean
make HELIX=verbose,no_ani helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/branch_md5.txt
diff -u /tmp/master_md5.txt /tmp/branch_md5.txt
```
Test result:
```
--- /tmp/master_md5.txt 2020-01-03 15:42:22.000000000 +0900
+++ /tmp/branch_md5.txt 2020-01-03 15:42:42.000000000 +0900
@@ -1,4 +1,4 @@
-master
+refactor_rgblight_reconfig.h
MD5 (helix_rev2_default.hex) = f360032edd522448366d471d8f4f8181
MD5 (helix_rev2_back_default.hex) = 0c663acc6cccc44476b3b969ad22a48f
MD5 (helix_rev2_back_default.hex) = e66b1195ff6d38e6e22c975b8ae42fd3
```
* Expressions that are too long are difficult to read, so wrap them.
* Edit the expression again
* remove `defined(RGBLIGHT_ANIMATIONS)` in `tmk_core/common/*/suspend.c`, `tmk_core/protocol/*/main.c`
move contents of rgblight_reconfig.h to rgblight.h.
The following changes were made to rgblight.h.
```diff
+#ifdef RGBLIGHT_USE_TIMER
void rgblight_task(void);
void rgblight_timer_init(void);
void rgblight_timer_enable(void);
void rgblight_timer_disable(void);
void rgblight_timer_toggle(void);
+#else
+#define rgblight_task()
+#define rgblight_timer_init()
+#define rgblight_timer_enable()
+#define rgblight_timer_disable()
+#define rgblight_timer_toggle()
+#endif
```
The following changes were made to tmk_core/common/avr/suspend.c, tmk_core/common/chibios/suspend.c, tmk_core/protocol/chibios/main.c, tmk_core/protocol/lufa/lufa.c, tmk_core/protocol/vusb/main.c.
```diff
-# ifdef RGBLIGHT_ANIMATIONS
rgblight_timer_enable();
-# endif
```
```diff
-#if defined(RGBLIGHT_ANIMATIONS) && defined(RGBLIGHT_ENABLE)
+#if defined(RGBLIGHT_ENABLE)
rgblight_task();
#endif
```
* remove 'defined(RGBLIGHT_ANIMATIONS)' in tmk_core/common/keyboard.c
Co-authored-by: Joel Challis <git@zvecr.com>
* Compile error if ONESHOT_TIMEOUT defined but oneshot disabled
When ONESHOT_TIMEOUT and NO_ACTION_ONESHOT are both defined, this code
fails to compile.
Wrap the one usage of ONESHOT_TIMEOUT that is inconsistent with the
rest so all usages are properly wrapped by a check of NO_ACTION_ONESHOT.
* Run file through clang-format
Co-authored-by: Ted M Lin <tedmlin@gmail.com>
* Option to use function for KEYCODE2 routines.
Convert the KEYCODE2SYSTEM and KEYCODE2CONSUMER macros to functions,
defaulting to using the macros. The function form allows the compiler
to optimize the switch statement itself, over the macro nested
ternaries.
To enable this feature, #define USE_KEYCODE2_FUNCTION.
Testing against a random selection of avr-based keyboards, this
increased available flash by ~500 bytes. For arm-based keyboards,
the available flash increased by ~400 bytes.
* Replace macro with function entirely.
As zvecr states, go bold and just commit to using the function instead
of the macro.
* Reformat whitespace now that functional review is done
Verified against clang-format output.
* Dedupe extrakey report struct, and send functions in V-USB & LUFA
* Doc comment for consistency
* Wrap it in ifdef to prevent unused function error
* Do the same for ATSAM
- uprintf -> dprintf
- Fix atsam "vendor" eeprom.
- Bump Kinetis K20x to 64 bytes, too.
- Rollback Kinetis to 32 bytes as partitioning can only be done once. Add warning about changing the value.
- Change RAM-backed "fake" EEPROM implementations to match eeconfig's current usage.
- Add 24LC128 by request.
* Run clang-format manually to fix recently changed files
* Run clang-format manually to fix recently changed files - revert template files
* Run clang-format manually to fix recently changed files - format off for ascii_to_keycode_lut
* Implement IGNORE_MOD_TAP_INTERRUPT_PER_KEY
- Add configurable option IGNORE_MOD_TAP_INTERRUPT_PER_KEY
- Add function get_ignore_mod_tap_interrupt iff the option is enabled
Unless IGNORE_MOD_TAP_INTERRUPT_PER_KEY is defined, this patch does not affect the resulting binary.
* Add documentation for IGNORE_MOD_TAP_INTERRUPT_PER_KEY
* Move some common matrix code to a common location
* Refactor some 'custom_matrix_helper' logic to use custom matrix lite
* Fix build for kinesis/stapelberg - abuse of vpath was picking up matrix.c from core when custom matrix was enabled
* Add validation for CUSTOM_MATRIX
* VIA Refactor
* Remove old code
* review changes
* review changes
* Fix cannonkeys/satisfaction75/prototype:via build
* Add via.h to quantum.h
* Move backlight init to after backlight config load
* Merge branch 'master' into via_refactor_pr
* Update user's rules.mk to new way of enabling VIA
* Added id_switch_matrix_state
* Review changes
* Add central location for chibios defines
* Add central location for chibios defines - actually add files this time....
* Add Copyright header
* Update include order to resolve i2cv1 build errors
* Align endpoint config as per rest of file (fixes#4783)
* Add comments about explicit order use
* Update tmk_core/protocol/chibios/usb_main.c
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Set proper AVR part for USBasp avrdude flashing
* Remove `PROGRAM_CMD` stuff from rules.mk as they should not be needed anymore
* Missed the Plaid readme
* Remove PROGRAM_CMD from Mysterium
* Initial ARM bitbang ws2812 driver
* Unify chibios platform to run rgblight_task
* Remove 'avr only' comments from ws2812 docs
* Remove 'avr only' comments from ws2812 docs
* Unify chibios platform to run rgblight_task - review comments
* Remove debug flags from keymap
* Add comments from review
* Add defines for STM32L0XX
* Attempt to get arm ws2812 working on multiple gcc versions
* Move tmk_core/common/backlight to quantum/backlight
* Add guards to backlight inclusion
* Add guards to backlight inclusion
* Update backlight guards on clueboard/60
* Use full paths to avoid vpath issues
* Initial stab at some fake dfu-util-split-left behaviour
* Apply suggestions from code review
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Clang format fixes
* Fake eeprom init for both left and right hand
* Fix battery level code in adafruit_ble.cpp
The code in tsk_core/protocol/lufa/adafluit_ble.cpp that polls the
battery level for the Adafruit feather BLE controller reads the
regulated voltage, not the raw voltage coming from the battery. To do
that, the Adafruit Feather docs say you should read from pin A9:
https://learn.adafruit.com/adafruit-feather-32u4-basic-proto/power-management#measuring-battery-4-9.
(See also
https://learn.adafruit.com/adafruit-feather-32u4-bluefruit-le/pinouts#logic-pins-2-9.)
I'm not sure why, but analogRead(9); doesn't read the correct pin.
Checking all available analog pins experimentally, it turns out that
analogRead(7); returns the correct value. So the code above should read:
state.vbat = analogRead(7);
* Update tmk_core/protocol/lufa/adafruit_ble.cpp
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Remove old comment
* Fix linking error
* Remove `#ifdef` around `#include analog.h`.
* Really fix linking error
* Fix indentation
* Fix braces
* Expand descriptor headers
* Align descriptor elements
* Nicer formatting
* Tidy up preprocessor statements
* Remove VERSION_BCD redefine - LUFA_VERSION_INTEGER is currently 0x170418
* Tidy up comments
* Tweak ordering of HID report elements (no functional changes)
* We don't need all of these newlines
* Move default USB_MAX_POWER_CONSUMPTION closer to where it makes sense
* Ask nicely
* Add some more comments
* Change indentation back to 4 spaces
* Add changelog entry
This will manually wipe the EEPROM. This is a hacky solution for when new ranges are added or moved around.
A better (more complicated) solution would be to zero out everything, not just known ranges. But for now, this is a hacky solution that will work.
* Additional changes for Layer State typedef compatibility
* Replace biton32 with get_highest_layer in docs
* Change additional layer structure code
* Fix uGFX reference issue
* Remove dynamic_keymap check
* Where did all these extra spaces come from
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Add MAGIC_SWAP_CONTROL_LGUI and MAGIC_UNSWAP_CONTROL_LGUI keycodes
Key codes to swap and unswap the control and windows/cmd keys
* Fix issues with pull request #6110
Renamed swap/unswap lctl and lgui key codes, added key codes to swap/unswap rctl and rgui, and moved new bool inside keycode_config.h struct to the end
* Move new keycodes to the end of the enum (#6110)
* add cases for swapped control and OS keys to mod_config (#6110)
* Add new keycodes to feature_bootmagic.md (#6110)
* Add R+L swap codes to keep in parity with AG_* codes
* Extend Magic range check to include new magic codes
* Update audio docs
* Combine 2 byte ranges into 1 word for EECONFG
Fix names for Keymap config EEPROM
* Update docs/feature_bootmagic.md
Co-Authored-By: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
* Update docs/feature_bootmagic.md
Co-Authored-By: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
* Update docs/feature_bootmagic.md
Co-Authored-By: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
* Update docs/feature_bootmagic.md
Co-Authored-By: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
* Remove superfluous JTAG disable code
* 32A has differently named register
* Accidentally some operators
* 32A also has different JTAG pins
* Wrap disable_jtag() in an ifndef
* Document this new define
* Rename the define, it conflicts with a LUFA thing
Also, move the ifndef wrapping to the call in keyboard_setup()
* Add universal flash command
* Add bootloader info to I:C boards
* Add support for ATSAM
* Add messages for flash target
* Message cleanup
* Add USB ASP Flashing target
* Make usbasp target more universal
* Add phoney target for usbasp
* Clarify error message when bootloader isn't matched
* Extend allowed range of tappable keycodes to include modifiers
* Get rid of the magic numbers altogether
* Remove some more magic numbers
* Extract LM() functionality from ACT_LAYER_TAP
* Use ACTION() macro everywhere
* Update IS_COMMAND definition in templates to use MOD_MASK_SHIFT
* Update IS_COMMAND in docs
* Update IS_COMMAND default definition in tmk_core
* Update table in Command docs based on suggestion
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update the :bootloader target to pass along correct hardware info
* Update make scripts to properly grab the settings (a big thanks to @yanfali)
* Remove LUFA debug warnings
* Store backlight breathing state in EEPROM
* Reduce backlight_config.level from 6 bits to 4 (max 15 "on" levels)
* Error out if BACKLIGHT_LEVELS is > 15
* Remove mention of default backlight pin in rules.mk template
* Remove pointless comment
Zeroing out spd in eeconfig_init_quantum
Switched to block read & update
Update tmk_core/common/eeconfig.h
Co-Authored-By: Drashna Jaelre <drashna@live.com>
Fixing init compile error
Update eeconfig.c
Dead / Missing API cleanup
alignment
* Typedef'ed layer_state_t to uint32_t.
This enables future work with layer_state_t to uint8_t for optimization purposes.
* Removed accidental xeal60 commit
* Revert to egyptian brackets, added sizeof(layer_state_t) so when layer_state_t is redefined it will automagically work.
* Add additional typedefs
* Add checks for setting layer state
* Update tmk_core/common/action_layer.h
Co-Authored-By: alex-ong <the.onga@gmail.com>
* Revert commit.
* Increase delay for Hold-Tap register for CAPSLOCK
Because it seems that the 80ms delay wasn't too much
* Screw it, make the caps delay a define and make it configurable
* clean up rgb matrix extern usage
Moved rgb matrix boiler plate into macros
Rebased onto typing heatmap pr
* Fixing the reversed frame buffer access in digital rain
* Fixing digital rain & typing heatmap if keyreactive effects are not enabled
* Apply suggestions from code review
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Adding parenthesizes to DRIVER_LED_TOTAL where necessary
* Updated docs
* added notes about parentheses
* Initial conversion of the rgb_led struct
* Converting last keyboard & updating effects to take advantage of the new structure
* New struct should not be const
* Updated docs
* Changing define ___ for no led to NO_LED
* Missed converting some keymap usages of the old struct layout
* Re-fix Mousekey Movements
After the new movement model was instroduced, it broke diagonal momement, again. Reapplying fix from #3147 to both old and new acceleration method.
* Make diagonal mouse report checks more readable
Co-Authored-By: drashna <drashna@live.com>
* Add DFU Suffix for ARM boards
* Blindly flash DFU SUFFIX ARGS for now
* Fix commented out check
* Fix DFU Suffix Argument check
Thank you jack!
* Update Travis CI Scripts to include dfu-util
So we can get dfu-suffix as well
* Manually add dfu-suffix package
* Use external repo for newer version of dfu-util
One that includes dfu-suffix
* Update .travis.yml
* Silence unnecessary output from dfu-suffix
Patch from https://github.com/qmk/qmk_firmware/issues/3657#issuecomment-415147411
Long story short, in avr-gcc pre-8.2, reset_key was assigned to a memory area that was in a normal range, but when 8.2 came out, that memory got moved to an out of range area, causing errors like 0x800293 out of range. Apparently, this was fixed up in avr-gcc, but we haven't seen a release with the fix yet (we expected it in 8.3, but that didn't happen for some reason).
What this commit does is move the reset_key back to the original memory location it was in before.
When waking from suspend, only enable the LED drivers if they were not previously set to disabled by the user. This functionality was removed by the recent updates to adapt Massdrop keyboards to QMK RGB Matrix. Affects Massdrop CTRL and ALT keyboards compiled using Massdrop Configurator mode.
Assuming I understand this correctly, this should set the max scancode to E7 (RGUI), which is the last listed code in the main list (everything else use for internal QMK/TMK stuff).
* Add customizable tapping terms
* Add Documentation
* Fix function
* Fixes
* It's not a pointer
* Add debugging output
* Update documentation to be at least vaguely accurate
* Use `get_tapping_term(tapping_key.event)` instead
`e` doesn't include column and row information, properly. It registers as 255, regardless of the actual keypress.
However `tapping_key.event` actually gives the correct column and row information. It appears be the correct structure to use.
In fact, it looks like the issue is that `e` is actually the "TICK" structure, as defined in keyboard.h
* Use variable tapping term value rather than define
* Silly drashna - tapping_key.event, not event
* add get_event_keycode() function
* Fix typo
Co-Authored-By: drashna <drashna@live.com>
* Remove post_process_record_quantum since it's the wrong PR
* Update quantum/quantum.c
Co-Authored-By: drashna <drashna@live.com>
* Better handle ifdef statement for permissive hold
Since we can't be sure that tapping term is actually 500
* Update quantum.c comments based on feedback
* Clean up get_tapping_term function
Clean up function so that users don't need to call the event function, and instead only check the keycode
* Add ability to run functionality on and off
* Make ifdef's more compact
* port Massdrop CTRL/ALT to use RGB Matrix
Co-authored-by: Matt Schneeberger <helluvamatt@gmail.com>
* Massdrop lighting support working
This commit is to get the Massdrop lighting code working again through use of the compilation define USE_MASSDROP_CONFIGURATOR added to a keymap's rules.mk.
Added keymaps for both CTRL and ALT named default_md and mac_md. These should be used if the Massdrop style lighting is desired.
* Updating config based on testing results with patrickmt & compile errors
* Updates for PR5328
For CTRL and ALT:
Moved location of new RGB Matrix macros from config_led.h to config.h.
Added RGB_MATRIX_LED_FLUSH_LIMIT (time between flushes) to config.h for correct LED driver update timing.
Re-added missing breathing code for when Massdrop configurator mode is defined.
* remove prilik keymap form PR
* build size-check enhancement
Changed to display a warning when the free size of compilation result is less than 512 bytes.
* update message.mk
* add SIZE_MARGIN variable, change default margin 512 to 1024
for Example.
```
$ make SIZE_MARGIN=2048 crkbd:all
$ make crkbd:all ## mergin is 1024
```
* Update message.mk
change message to ‘approaching the maximum’
Co-Authored-By: mtei <2170248+mtei@users.noreply.github.com>
* sleep until usb port becomes writable before running avrdude
* only wait for a writable USB port when not on MSYS
using MINGW or MSYS: sleep for one second, as before.
otherwise: wait for the port to become writable.
* typo
* typo
* Draft commit of typing speed RGB control
* More information in the readme
* Support all RGB animation modes (Fixes#1)
* Added support for all RGB light modes to use typing speed
Except christmas lights because that is seizure-inducing at high speeds!
* Introduced a value range specific to each RGB mode
Because some modes are a little too much when running at full speed!
* Update readme.md
* Update readme.md
* Re-arrange typing_speed definitions (Fixes#5) (#6)
* Re-arrange variable definitions to avoid including quantum.h from rgblight.c
* Fix a compilation error when trying to run make test:all
* Tweaks to the typing speed decay rate
* Renamed to momentum; moved implementation into dedicated files
* Groundwork for toggling momentum on/off (currently always on)
* Add EEPROM toggle for momentum-matching
* Moved momentum out of RGBLIGHT_ENABLE toggles so it's more generic
* Move momentum decay task out of rgblight_task()
* Fix missing momentum.h in lufa.c
* Experimental LED support (untested)
* Draft commit of typing speed RGB control
* More information in the readme
* Support all RGB animation modes (Fixes#1)
* Added support for all RGB light modes to use typing speed
Except christmas lights because that is seizure-inducing at high speeds!
* Introduced a value range specific to each RGB mode
Because some modes are a little too much when running at full speed!
* Update readme.md
* Update readme.md
* Re-arrange typing_speed definitions (Fixes#5) (#6)
* Re-arrange variable definitions to avoid including quantum.h from rgblight.c
* Fix a compilation error when trying to run make test:all
* Tweaks to the typing speed decay rate
* Renamed to momentum; moved implementation into dedicated files
* Groundwork for toggling momentum on/off (currently always on)
* Add EEPROM toggle for momentum-matching
* Moved momentum out of RGBLIGHT_ENABLE toggles so it's more generic
* Move momentum decay task out of rgblight_task()
* Fix missing momentum.h in lufa.c
* Added documentation
* Renamed feature to velocikey
* Reverted readme to original state
* Correct the readme title
* Updated feature name in the docs
* Update EECONFIG name
* Add compile-time toggles for velocikey
* Update feature documentation
* Revert "Merge branch 'led-support' into master"
This reverts commit e123ff5feb, reversing
changes made to df111a55b9.
* Move velocikey EECONFIG definition to depend on VELOCIKEY_ENABLE
* Rename decay_task function to decelerate
* Apply suggestions from code review
Co-Authored-By: chrislewisdev <chris@chrislewisdev.com>
* Re-order eeconfig definitions
* Apply coding conventions
* Apply #ifdef check in lufa.c
* Refactored interval time checks into one functionc
* Small rename
* Fix unused function error for layouts not using all rgb effects
* Only update EEPROM if Velocikey is enabled
* Incorporate code review feedback
* Small adjustment to top-end decay rate
* Add Velocikey documentation to table of contents
* Bring tetris:default keymap size down by disabling audio
* Changed use of '\s' in grep to '[ \t]' for portability
* Pushed DFU Keyboard.h into a shell script
* Fixed execution permissions on make_dfu_header,sh
* Change Command keycode defaults to match corresponding Bootmagic codes
* Make alternate magic key keycodes consistent
* Reflect changes from previous commit in tmk_core/common/command.c
* Remove unnecessary MAGIC_KEY_* definitions from keymaps compatible with these changes
* Swap E and BSPACE for MAGIC_KEY_EEPROM
* Add MAGIC_KEY_EEPROM_CLEAR instead of MAGIC_KEY_EEPROM_ALT
* Remove BOOTMAGIC_ENABLE checks around EECONFIG stuff
* Update Command descriptions
* initial work to add eeprom to haptic feedback and decouple the feedback process from keyboards
* Haptic feedback enhancements: on/off toggle working, feedback order working
todo:
-work on modes switching
-get modes switching to save to eeprom
* haptic enhancement - eeprom and modes added
* Added set and get functions for haptic feedback
* initial implementation of solenoids under haptic feedback
* changed eeprom to 32 bits to reserve blocks for future features
* start documentation of haptic feedback
* change keycode per comment from reviewers
* typo fixes
* added eeprom for solenoid configs
* added solenoid and docs
* Add/fix default parameters configs, improve docs
* more doc cleanup
* add in solenoid buzz toggle, clean up doc
* some fixes for error in compiling solenoid
* fix a chibios specific i2c read function and added one for AVR controllers in DRV2605L.c
* fixes for avr side issues
* update keymap
* fix keymap compile error
* fix bugs found during solenoid testing
* set pin that is not powered during bootloader
* added warning about certain pins on the MCU may trip solenoid during DFU/bootloader
* Added xeal60 via clone of lets split
* Delete removed other keymaps
* Basic keymap (no FN). Compiles.
* Removed NP_STAR and NP_SLSH.
* Removed "debounce_algo = manual" in all keyboards with CUSTOM_MATRIX = yes.
* Changed order of rules in TMK. Documented feature.
* Fixed missing whitespace in debounce documentation
Table wasn't working due to missing newline.
* Added bold in a few areas.
* DO NOT USE - Removed debounce from TMK.
* Remove accidental xeal60 commit
* DO NOT USE - debounce successfully compiled.
* DO NOT USE Revert back to original API to support split_keyboards.
* Working eager_pk
* Whitespace cleanup.
* Restored debounce.h since there wasnt any real change.
* Moved debouncing_time variable to inside #if debounce
* Removed check for custom_matrix. We can safely include the debounce file for compilation when custom_matrix is used.
* Removed #include "matrix.h" from debounce.h
* Bug fix - was using MATRIX_ROWS instead of num_rows
* Fixed compilation error with debounce_sym_g
* Renamed DEBOUNCE_ALGO to DEBOUNCE_TYPE
* Malloc array in debounce_eager_pk, since split keyboards only use MATRIX_ROWS/2.
* Fix compile error in debounce_eager_pk
* Stricter, leaner DEBOUNCE_TYPE section in common_features.mk. Cleanup debounce_type.mk
* Add suspend functions
* Disable RGB code if it's disabled
* Add keyboard_init functions
* Change where references so it will compile
* Wrong command chained in wake up kb function
* Fix non-feature file changes
* Add documentation
* Re-add matrix init docs
* add rgblight code to example
* Remove suspend code
* Clean up docs
* Fix docs
* Fix suspend code
* more doc fixes
* change function to startup_* rather than keyboard_init_
* fix spelling error
* fix up docs to finish removing keyboard_init
* Use Pre and Post init functions
* Update Documenation
* Remove changes to my keymap and userspace code
* Cleanup
* Revert changes to extra files
* Forgot a semicolon
* Make sure all protocols call keyboard_setup
* Cleanup functions
* Unset startup_user
* Remove changes from division keyboard
* Readd startup_user function
* Remove all to startup_user
* Update docs/custom_quantum_functions.md
Co-Authored-By: drashna <drashna@live.com>
* Update docs/custom_quantum_functions.md
Co-Authored-By: drashna <drashna@live.com>
* Add suggestion line
* Rebase fixes
* Update documentation to be more useful/accurate
* Cleanup of documentation
* Fix spacing inconsistency
* Revert unexpected change to keymap
* Add stm32f072 base ck4x4 to handwired
* add prints
* Save these tries
* Save changes again
* Working hadron oled
* OLEd working but ws2812b still iffy:
* save another try
* Encoder feature + OLED
* RTC code
* Implement clock setting mode
* Whitespace
* Encoder hooked up to working LED PWM code
* Add missing files
* eeprom changes
* Save changes
* Move i2c master
* Move satisfaction75 under cannonkeys
* Set proper default folder
* Revert some core changes
* Undo paved iris changes
* Reorganize code for maintainability and prep for new features
* Add starting code for clock OLED mode
* Clock set mode finished
* Add custom encoder modes
* Actually add VIA keymap
* Gate to only 072
* fix gate for only 072
* Update header guards and includes
* Update i2c selection strategy
* Update board.c to handle software reset to DFU
* Grab HEX and BIN files from autogen
And push them to qmk.fm/compiled
* Make autogen copy extension agnostic
This way, when travis cl scrpit looks for hex files, it will actually grab bin files, and not hex files for ARM boards
* Handle the AUTOGEN in :bin target to properly handle edge cases
Both the TADA68 and ATSAM boards generate the hex file and then convert it to a bin file. The changes I made does not handle this well, at all. This removes the hex and replaces it with a bin, if a bin is normally generated.
* Revert hex target to original copy command
* Check hex and bin separately in compile push script
Since I don't know how to script this, well
* Simplify push to compiled folder
* Further simplify compiled push script
* Move AUTOGEN parsing to a more sane location to prevent tech debt
Thanks to skully!
* Remove AUTOGEN completely, as it's not needed
This has the benefit of making everything super simple, since we can pull every hex and bin from the root of the qmk_firmware folder, and move that to th compiled folder. This also removes old and unneeded code, and removes some tech debt that has been accrued, without adding more, in theory.
* Added callbacks to one shot modifier changes
* Altered signature of callback functions
* Reordered the callback methods, shortened brief documentation
* Added One Shot Modifier callback documentation
* First attempt at unit tests
* Revert "First attempt at unit tests"
This reverts commit 5ec21a7822.
* Simplified oneshot function implementations
* Made clear_oneshot_locked_mods to be conform action_util.h, adhering to the (void) signature
* Made used datatypes for oneshot mods consistently unsigned integers
* Corrected callback to call clear callback when clear_oneshot_locked_mods is invoked
* Simplified oneshot equals statements
* Corrected return type and signature of get and set oneshot locked mods
* Consolidated one shot callbacks, added initial layer callback version
* Fixed non-updating one shot layer variable after timeout or other clear, added code comments
* Added better one shot key docs
* Move boards to cannonkeys and share resources
* Share common files between cannonkey boards
* Fix ortho60 keymap
* update LED numbers
* Add RGB keys to Ortho60 and Ortho48
* Add Backlight control to default layout Ortho60 and 48
* Remove unnecessary ws2812.c SRC from rules.mk
* [BACKLIGHT_CAPS_LOCK_INDICATOR] Use backlight toggling as Caps Lock LED
I've implemented this feature because S65-X doesn't have LED indicators
and the existing led_set_kb(usb_led) function try to use backlight as
indicator but that creates an inconsistency with backlight_config state.
- define `BACKLIGHT_CAPS_LOCK_INDICATOR` to enable Caps Lock indicator
using backlight (for keyboards without dedicated LED)
- Don't turn off LED indicators when suspend because backlight is
already turned off. Else led_set(0) will turn back on backlight.
- Documentation has been updated
* [BACKLIGHT_CAPS_LOCK_INDICATOR] Turn off all LED indicators except Caps Lock if BACKLIGHT_CAPS_LOCK_INDICATOR
* [BACKLIGHT_CAPS_LOCK] Rename BACKLIGHT_CAPS_LOCK_INDICATOR
* [BACKLIGHT_CAPS_LOCK] Use new IS_LED_ON method
* Remove unnecessary IS_COMMAND definition in clueboard/66/rev4
* Replace keyboard_report->mods with get_mods() in IS_COMMAND definitions
* Update docs to use get_mods() instead of keyboard_report->mods
* Replace keyboard_report->mods with get_mods() in tmk_core/protocol/usb_hid/test
For some reason, this occurrence used KB_LSHIFT and KB_RSHIFT, which don't exist
* Replace keyboard_report->mods with get_mods() in Massdrop keyboards (as per @patrickmt)
* Add default value for IS_COMMAND for COMMAND feature
* Cleanup and consistency
* Update Templates to reflect change
* Fix IS_COMMAND in template
* Fix IS_COMMAND define
* Use consistent IS_COMMAND block in templates
* Remove unnecessary `#undef IS_COMMAND` directives
* Fix compile issue on orthodox
* Reomve IS_COMMAND option for newer boards
* Remove all existing definitions of IS_COMMAND if they use default LSHIFT and RSHIFT setting
* Remove a couple of additional IS_COMMAND defines
* Remove remaining redundant IS_COMMAND definitions
* Remove #undef IS_COMMAND from orthodox:drashna and whitefox:konstantin
* Remove multiple empty lines in modified config.h files
* Update additional boards
* Reomve IS_COMMAND from newer boards
* Update Alice keyboard
* Remove IS_COMMAND from additional boards
Jan 24th edition
* Only re-enable RGBLIGHT if it was on when going to sleep
* Reformat file to follow QMK Standards
* Fix check, since this is a loop, whoops
Much thanks to @Rockman18 for catching this and posting the additional code!
* Add ability to animate arm_atsam led matrix from the center of a circle
* Make arm_atsam led matrix circular animation circular rather than obloid
* Fix indentation in tmk_core led_matrix.c
When this if statement is false, it will cause the report ID to be read as the LED state.
We already know there are two bytes in the endpoint, which is a reasonably good indicator that it contains a report ID, so we should always read both.
* Defined IS_(HOST_)LED_ON/OFF() and improved LED documentation
* Update docs/custom_quantum_functions.md
Co-Authored-By: DidierLoiseau <didierloiseau+github@gmail.com>
* Update docs/custom_quantum_functions.md
Co-Authored-By: DidierLoiseau <didierloiseau+github@gmail.com>
* Integrated @drashna and @fauxpark's PR comments
- changed all plurals of "LED" to "LEDs" in the file
- rewording of the note about host_keyboard_leds() vs. led_set_user()
* Update docs/custom_quantum_functions.md
Co-Authored-By: DidierLoiseau <didierloiseau+github@gmail.com>
* Eliminate separate slave loop
Both master and slave run the standard keyboard_task main loop now.
* Refactor i2c/serial specific code
Simplify some of the preprocessor mess by using common function names.
* Fix missing #endif
* Move direct pin mapping support from miniaxe to split_common
For boards with more pins than sense--sorry, switches.
* Reordering and reformatting only
* Don't run matrix_scan_quantum on slave side
* Clean up the offset/slaveOffset calculations
* Cut undebounced matrix size in half
* Refactor debouncing
* Minor fixups
* Split split_common transport and debounce code into their own files
Can now be replaced with custom versions per keyboard using
CUSTOM_TRANSPORT = yes and CUSTOM_DEBOUNCE = yes
* Refactor debounce for non-split keyboards too
* Update handwired/xealous to build using new split_common
* Fix debounce breaking basic test
* Dodgy method to allow a split kb to only include one of i2c/serial
SPLIT_TRANSPORT = serial or SPLIT_TRANSPORT = i2c will include only
that driver code in the binary.
SPLIT_TRANSPORT = custom (or anything else) will include neither, the
keyboard must supply it's own code
if SPLIT_TRANSPORT is not defined then the original behaviour (include
both avr i2c and serial code) is maintained.
This could be better but it would require explicitly updating all the
existing split keyboards.
* Enable LTO to get lets_split/sockets under the line
* Add docs for SPLIT_TRANSPORT, CUSTOM_MATRIX, CUSTOM_DEBOUNCE
* Remove avr-specific sei() from split matrix_setup
Not needed now that slave doesn't have a separate main loop.
Both sides (on avr) call sei() in lufa's main() after exiting
keyboard_setup().
* Fix QUANTUM_LIB_SRC references and simplify SPLIT_TRANSPORT.
* Add comments and fix formatting.
* Check the size of the SET_REPORT packet
If we have two bytes, that probably means the first is a report ID. The 6KRO interface may or may not have one, but the NKRO interface always does, so we need to check this regardless of whether KEYBOARD_SHARED_EP is defined.
* Fix indentation
Microsecond (us) delays are now handled by a busy wait loop according to MCU frequency. This replaces the system counter method which had an overhead of around 12us.
TC5 device and supporting routines removed as it was the old us delay counter.
wait_ms is now properly a macro to CLK_delay_ms.
wait_us is now properly a macro to CLK_delay_us.
Removed CLK_get_us as it has no use.
All calls to CLK_get_ms() have been replaced by timer_read64() with corrected typing.
All calls to CLK_delay_ms() have been replaced by wait_ms().
All calls to CLK_delay_us() have been replaced by wait_us() and timings verified or updated as needed after review on scope.
Corrected typing of variables using 64bit ms timer readings if needed.
* initial commit, this now mostly works
- RGB controls work
- Dynamic keymap still broken due to eeprom
- Via works
* STM32 eeprom update
- Update EEPROM emulation library to handle 8bit data like AVR.
- This library also allows for multiple page pairs resulting in greater EEPROM size flexibility
* hs60 changes
* HS60 hhkb added
* Update keyboards/hs60/v2/config.h
Co-Authored-By: yiancar <yiangosyiangou@cytanet.com.cy>
* Keep pressed keys on layer state change
* Add doc comment for clear_keyboard_but_mods_and_keys
* Keep pressed keys only if PREVENT_STUCK_MODIFIERS is on
* Check STRICT_LAYER_RELEASE instead of PREVENT_STUCK_MODIFIERS
* add temporary compile test shell script
* Extended support of SKIP_VERSION to make invariant compile results during testing.
* build_keyboard.mk, tmk_core/rules.mk: add LIB_SRC, QUANTUM_LIB_SRC support
Support compiled object enclosed in library.
e.g.
```
LIB_SRC += xxxx.c
xxxx.c --> xxxx.o ---> xxxx.a
```
* remove 'ifdef/ifndef USE_I2C' from quantum/split_common/{i2c|serial}.c
* add SKIP_DEBUG_INFO into tmk_core/rules.mk
When SKIP_DEBUG_INFO=yes is specified, do not use the -g option at compile time.
* tmk_core/rules.mk: Library object need -fno-lto
* add SKIP_DEBUG_INFO=yes
* remove temporary compile test shell script
* add '#define SOFT_SERIAL_PIN D0' to keyboards/lets_split/rev?/config.h
* quantum/split_common/serial.c: Changed not to use USE_I2C.
* Add delay in Tap Code to avoid issues
I think a few people have reporting issues with it working properly, and it may be a timing issue. The 'register_code' uses this sort of delay in some of the functions, and
this is probably why.
Adding the 100ms delay should hopefully fix any issues with it.
* Make tap_code delay configurable
* Update documentation
* Bring tap_code16 inline with changes
* Fix type for tap_code16
Bad copy-paste job
* Just use the value check for the define
* Clarify timing in docs
Co-Authored-By: drashna <drashna@live.com>
* Wordsmithing
Co-Authored-By: drashna <drashna@live.com>
* Add standard ALGR defition, remove (re)definitions from language files
* Use ALGR(kc) consistently in ALTGR(kc) aliases
* Non-Nordic keymaps should not use NO_ALGR
* Add standard KC_ALGR definition
* Update docs with ALGR and KC_ALGR
* Update SS_ALGR and ALGR_T aliases
MCU Pins for debugging, LED, boot tracing, and shift registers are now configurable at keyboard level.
Macros led_* replaced by DBG_LED_*
Macros m15_* replaced by DBG_1_*
Macros m27_* replaced by DBG_2_*
Macros m28_* replaced by DBG_3_*
For CTRL and ALT keyboards, debug boot tracing pin default now set to pad M27 instead of M28 since although M28 is not being used, it is technically a signal for USB port detection.
m15_print(...) renamed to dbg_print(...) to get away from hard coded port names.
dbg_print function now follows similar pattern to debug led output.
* Add initial support for vertically-oriented animations
* DRY up vertical animation support
* Fix animation code for arm_atsam led_matrix to work in all directions
* Adjust py calculation to base off bottom rather than top
* add initial support for hadron ver3
* add initial support for hadron ver3
* pull qwiic support for micro_led to be modified for use in hadron's 64x24 ssd1306 oled display
* initial work on OLED using qwiic driver
* early work to get 128x32 oled working by redefining qwiic micro oled parameters. Currently working, but would affect qwiic's micro oled functionality
* moved oled defines to config.h and added ifndef to micro_oled driver
* WORKING :D - note, still work in progress to get the start location correct on the 128x32 display.
* added equation to automatically calculate display offset based on screen width
* adding time-out timer to oled display
* changed read lock staus via read_led_state
* lock indications fixes
* Added scroll lock indication to oled
* add support for DRV2605 haptic driver
* Improve readabiity of DRV2605 driver.
-added typedef for waveform library
-added unions for registers
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Update keyboards/hadron/ver2/keymaps/default/config.h
Co-Authored-By: ishtob <ishtob@gmail.com>
* Fixes for PR
* PR fixes
* fix old persistent layer function to use new set_single_persistent_default_layer
* fix issues with changing makefile defines that broken per-key haptic pulse
* Comment fixes
* Add definable parameter and auto-calibration based on motor choice
* Unify multiple HID interfaces into one
This reduces the number of USB endpoints required, which frees them up
for other things.
NKRO and EXTRAKEY always use the shared endpoint.
By default, MOUSEKEY also uses it. This means it won't work as a Boot
Procotol mouse in some BIOSes, etc. If you really think your
keyboard needs to work as a mouse in your BIOS, set
MOUSE_SHARED_EP = no in your rules.mk.
By default, the core keyboard does not use the shared endpoint, as not
all BIOSes are standards compliant and that's one place you don't want
to find out your keyboard doesn't work.. If you are really confident,
you can set KEYBOARD_SHARED_EP = yes to use the shared endpoint here
too.
* unify endpoints: ChibiOS protocol implementation
* fixup: missing #ifdef EXTRAKEY_ENABLEs
broke build on AVR with EXTRAKEY disabled
* endpoints: restore error when too many endpoints required
* lufa: wait up to 10ms to send keyboard input
This avoids packets being dropped when two reports are sent in quick
succession (eg. releasing a dual role key).
* endpoints: fix compile on ARM_ATSAM
* endpoint: ARM_ATSAM fixes
No longer use wrong or unexpected endpoint IDs
* endpoints: accommodate VUSB protocol
V-USB has its own, understandably simple ideas about the report formats.
It already blasts the mouse and extrakeys through one endpoint with
report IDs. We just stay out of its way.
* endpoints: document new endpoint configuration options
* endpoints: respect keyboard_report->mods in NKRO
The caller(s) of host_keyboard_send expect to be able to just drop
modifiers in the mods field and not worry about whether NKRO is in use.
This is a good thing. So we just shift it over if needs be.
* endpoints: report.c: update for new keyboard_report format
* add functions to set specific backlight state
* add function to query backlight state
* update documentation with new backlight functions
* Update tmk_core/common/backlight.c
Co-Authored-By: codyd51 <phillip.ennen@gmail.com>
* Update tmk_core/common/backlight.h
Co-Authored-By: codyd51 <phillip.ennen@gmail.com>
* update docs for is_backlight_enabled() name change
Rewrote USB state tracking for implementation of suspend state.
Updated suspend.c in entirety.
Main subtasks (generally hardware related) are now run prior to keyboard task.
* add computed pins from mcu type
* update for atmega32a
* doc typo
* add atmega16 chips, link to references
* remove avr include from config
* exclude assembler in config.h includes
* consolodate options, add 646
* fix typo in pindef
* Preliminary additon of bootmagic lite functionality
* Cleanup code
* Clean up bootmagic code
* Add documentation and clean up code
* Make 'lite' an option for BOOTMAGIC_ENABLE
* Update Templates with note about Bootmagic Lite option
* Detect Debounce variable
* Make sure debounce is a non-zero number
* Capitalize Bootmagic
* Capitalize bootmagic
* Update wording
* Re-add EEPROM reset, by popular demand
And add eeprom-less version to drashna userspace for his sanity
* Fix spacing
* Set BOOTMAGIC_ENABLE to use full/lite/off
And default yes to "full" for compatibility
* Add Bootmagic lite info to templates
* Remove text from makefiles
* Cleanup of makefile
* mention yes in bootmagic docs
* Wordsmitthing the docs
* Fix white spaces
* Readd default bootmagic setting, because it's necessary
* Made DZ60 layout with calculator
* Cleaned up and commented, preparing to fix bug with negative in front of open parenthesis as first character
* Fixed bug where negative sign infront of parenthesis as first character was parsed incorrectly
* Made a better solution for the bug from the previous commit
* Modularized and added a userfile so that this code can be used on various keyboards, found in doogle999
* Removed commented code from keymap
* Made the layer that is used for calculations a define so that it can be changed per keyboard
* Made the readme
* Made the readme in the correct place
* Revert "Made the readme in the correct place"
This reverts commit 7f8b59ed9e.
* Manually synced with qmk upstream
* Stopped repeat, made keys print character that they are defined as rather than what the keyboard wants them to do
* Added support for numpad, might make all keycodes custom so that there is no need to change doogle999.c if you want to change the keycode that is associated with a function, also made numpad automatically activating an option
* Fixed some bugs with backspacing, updated the readme
* Fixed some bugs with numlock turning on at the wrong times when a shift key was down
* Made the return to layer work automatically instead of just forcing it to layer 0
* fixes and style changes, 20% decreased binary size
* Fixed some bugs with double printing and compilation errors on my side
* Fixed bug with exceeding the buffer size
* Removed changes that added const-ness
* Made changes so that backspace does not repeat to remove backspace bugs, still some bugs with recalculating without having typed anything
* Fixed obo error with calc main loop
* Made includes more accurate in keymap for dz60
* Moved flags to user makefile
* Converter: add XT USB converter from TMK
* Converter: port TMK code for USB converter to QMK
* Apply requested changes after code review by @drashna
- use "pragma once" instead of include guards
- use LAYOUT instead of KEYMAP
- allow customisation with matrix_init_user() and matrix_scan_user()
- set BOOTLOADER instead of BOOTLOADER_SIZE
- Add XT_ENABLE to OPT_DEFS
* Remove unnecessary lines
Added hid_listen USB device for arm_atsam USB protocol.
Debug printing is now done through the console device (CONSOLE_ENABLE = yes) rather than the virtser device, for viewing in hid_listen.
Function dpf(...) renamed to CDC_printf(...) and should now be called directly if intending to print to the virtual serial device.
* Add Function level EEPROM configuration
Add kb and user functions for EEPROM, and example of how to use it.
* Bug fixes and demo
* Additional cleanup
* Add EEPROM reset macro to example
* Forgot init function in list
* Move eeconfig_init_quantum function to quantum.c and actually set default layer
* See if removing weak quantum function fixes issue
* Fix travis compile error
* Remove ifdef blocks from EECONFIG so settings are always set
* Fix for ARM EEPROM updates
* Fix merge issues
* Fix potential STM32 EEPROM issues
* Update for SEND_STRING usage
Update for SEND_STRING usage.
Sending keyboard reports (kbd, nkro) now obey the minimum polling time.
While attempting to send a keyboard report and waiting for a USB poll, other functions of the keyboard, including LED effects and power management, will continue to operate at their intended intervals.
* Updates for send string, syscalls, stdio, debug prints, auto shift
Now properly waiting for previous keys sent over USB to complete before sending new.
Added heap to linker and now compiling with syscalls support.
Removed custom string functions and now using stdio.
dprintf now works as intended through virtser device.
* CTRL and ALT keymap updates
CTRL mac keymap updated
ALT default and mac keymap updated
ALT rules.mk added Auto Shift with default no
* Code cleanup as per discussion with vomindoraan
Code cleanup as per discussion with vomindoraan
* add 'mavrdude' target into tmk_core/avr.mk
I made it a little convenient when writing the same binary to multiple Pro Micro.
* rename target name 'mavrdude' to 'avrdude-loop'
* modify docs/flashing.md about avrdude-loop
* mdify docs/flashing.md again
* modifi docs/flashing.md 3rd
* Remove chording as it is not documented, not used, and needs work.
* Make Leader Key an optional feature.
* Switch from `PREVENT_STUCK_MODIFIERS` to `STRICT_LAYER_RELEASE`
* Remove `#define PREVENT_STUCK_MODIFIERS` from keymaps.
* Initial version of zeal60
* WIP
* Fixes issue #900
* Adding RGB underglow functionality.
Fixed a compile-time conflict caused by enabling RGB underglow functionality.
* Refactor RPC protocol
* Fix last merge
* README for RGB underglow updated.
* Additional README changes.
* Adding RGBW strip software-based current-limiting functionality.
* RGBW current-limiting functionality should be handled by RGBSTRIP_MAX_CURRENT_PER_LIGHT instead.
* Updated README to reflect implementation of built-in current limiting.
* Keymap readability improvements.
* Minor keymap improvements.
* Fixed LED driver init sequence, formatting
* Dimming implementation tested, working.
* Stab LEDs synced with spacebar hits in effects.
* RGB underglow tested and functional. Simplified README for RGB underglow.
* Undid accidental file deletion from previous merge conflict. Safer values for RGB underglow.
* Improved arrow key positions in keymap.
* Added functionality to correct uneven RGB underglow. Refactored related code.
* Reverted to safer values for underglow.
* Changes for v0.3
* Custom LED brightness scaling will take place after current adjustment in order to avoid being overridden.
* Create keymap.c
Added split backspace and split shift to ISO layout
* Create config.h
Turned on LEDs for new layout
* Fixed bug where left spacebar stabilizer LED (LC06) would adopt color of row above.
* Added hhkb_wilba keymap
* Update keymap.c
* Update keymap.c
* Update keymap.c
* Added indicators, full param setting via host
* Added "mousekey" layout
* Added Zeal65 support, factory test mode
* Keycode safe range changed, caused bugs
* Bumped EEPROM version due to change in QMK keycodes
* Disable HHKB "blocked" LEDs if KC_NO in keymap
* Added "disable_hhkb_blocker_leds"
* Required overridden function for keymaps in EEPROM
* Added polar coordinate mapping, effect speed
* Force Raw HID interface number to 1 always
* Fixed last merge from master
* Added effect speed to default keymaps
* add BACKLIGHT_ prefix to vars
* add BACKLIGHT_ prefix to vars
* Keymap speed effect; keymap improvements/fixes
Readme updated to match changes
* Refactored to use common IS31FL3731/I2C drivers
* Fixed make rules, backlight disabled feature
* Make split rightshift default for Zeal65
* Added M60-A as a "version" of Zeal60.
* Renamed IS31FL3731 driver functions
* Fix suspend_wakeup_init_kb() being defined twice
* First pass refactor dynamic keymaps
* Updated to changed I2C and ISSI drivers
* Refactor zeal_color.* usage to quantum/color.*
* Updated Zeal65, fixed dynamic_keymap
* Major refactoring of Zeal60 backlight and API
* Lots of little cleanups
* Added readme.md
* Added readme.md
* Added LAYOUT_60*() macros, refactored and cleaned up default keymaps
* Fix compile error in suspend.c
* Added Zeal65 LAYOUT macros, info.json
* Added rama/m60_a, deleted zeal60/keymaps/m60_a
* Fixed rama/m60_a/keymaps/proto
* Fixed compilation error for suspend.c
* Requested changes for PR
* Fixed readme.md images
* Another readme.md fix
* Added drashna's requested changes
* add temporary test code rgblight-macro-test1.[ch]
* rgblight.h : mode auto numberring and auto generate mode name symbol
No change in build result.
* rgblight.c use RGBLIGHT_MODE_xxx symbols
No change in build result.
* quantum.c use RGBLIGHT_MODE_xxx symbols
No change in build result.
* fix build break. when RGB_MATRIX_ENABLE defined
* add temporary test code rgblight-macro-test2.[ch]
* modify rgblight_mode_eeprom_helper() and rgblight_sethsv_eeprom_helper()
* modify rgblight_task()
* configurable each effect compile on/off in config.h
* update docs/feature_rgblight.md
* fix conflict. docs/feature_rgblight.md
* remove temporary test code rgblight-macro-test*.[ch]
* fix comment typo.
* remove old mode number from comment
* update docs/feature_rgblight.md about effect mode
* Revert "update docs/feature_rgblight.md about effect mode"
This reverts commit 43890663fc.
* some change docs/feature_rgblight.md
* fix typo
* docs/feature_rgblight.md update: revise mode number table
