mirror of
https://github.com/qmk/qmk_firmware.git
synced 2024-12-11 20:31:02 +00:00
0206bd9df3
* add bluepill mcu to splittest * fix typo * refactoring * mcu config goes to mcuconf.h of keyboard * keymap specific config goes to keymap config.h * keyboard specific depending of keymap goes to post_config.h * Apply suggested change Co-authored-by: Ryan <fauxpark@gmail.com> * Apply suggested change Co-authored-by: Ryan <fauxpark@gmail.com> * Apply suggested change Co-authored-by: Ryan <fauxpark@gmail.com> * Apply suggested change Co-authored-by: Ryan <fauxpark@gmail.com> * Apply suggested change Co-authored-by: Ryan <fauxpark@gmail.com> * splittest/bluepill: improve documentation Co-authored-by: Ryan <fauxpark@gmail.com>
66 lines
2.6 KiB
Markdown
66 lines
2.6 KiB
Markdown
# bluepill splittest
|
|
|
|
This is the splittest example for the bluepill MCU.
|
|
To trigger keypress, short together pins _B10_ and _B1_.
|
|
|
|
## Keyboard Configuration
|
|
|
|
The type of communication (bitbang, serial (half/full duplex)) is set by the keymap `config.h` file with variables with `SPLIT_` prefix.
|
|
So this example uses:
|
|
|
|
- `config.h` to set which SDI to use for serial. Either define `USE_SDI1_ON_STANDARD_ROLE_PINS`, `USE_SDI1_ON_ALTERNATE_ROLE_PINS` or `USE_SDI2` before the `#ifdef` that configures the default case when none of these variable is defined.
|
|
- `post_config.h` for defining the communication pins between the halves once the keymap is configured.
|
|
|
|
On your keyboard, you most likely will only use `config.h` because you'd have already chosen your communication scheme: serial type, SDI, pins.
|
|
|
|
## Wiring
|
|
|
|
### Switches
|
|
|
|
- Add switches to both Bluepills across B10 and B1 pins
|
|
|
|
### Handedness
|
|
|
|
Have a look at the [handedness documentation](https://docs.qmk.fm/#/feature_split_keyboard?id=setting-handedness)
|
|
|
|
- Add pull-up resistor to left side between VCC and A7
|
|
- Add pull-down resistors to right side between GND and A7
|
|
|
|
### Send power to the other half
|
|
|
|
- Connect the following pins on both sides together: GND, VCC
|
|
|
|
### Halves data connection
|
|
|
|
Choose one of the connection type
|
|
|
|
#### serial - bitbang
|
|
|
|
- Connect the B8 pins on both sides together
|
|
|
|
#### serial - usart half duplex
|
|
|
|
Check the [documentation](https://docs.qmk.fm/#/serial_driver?id=usart-half-duplex) to determine the pull-up resistor.
|
|
|
|
- To use the default usart (USART1) with the standard role pins,
|
|
- Connect the A9 pins on both sides together and to add a pull-up resistor on one of these pins
|
|
- Define USE_SDI1_ON_STANDARD_ROLE_PINS in config.h
|
|
- To use the default usart (USART1) with the alternate role pins,
|
|
- Connect the B6 pins on both sides together and to add a pull-up resistor on one of these pins
|
|
- Define USE_SDI1_ON_ALTERNATE_ROLE_PINS in config.h
|
|
- To use the usart2 (USART2) pins,
|
|
- Connect the A2 pins on both sides together and to add a pull-up resistor on one of these pins
|
|
- Define USE_SDI2 in config.h
|
|
|
|
#### serial - usart full duplex
|
|
|
|
- To use the default usart (USART1) with the standard role pins,
|
|
- Connect the mpins on A9, A10 one to the other on each side
|
|
- Define USE_SDI1_ON_STANDARD_ROLE_PINS in config.h
|
|
- To use the default usart (USART1) with the alternate role pins,
|
|
- Connect the pins B6, B7 one to the other on each side
|
|
- Define USE_SDI1_ON_ALTERNATE_ROLE_PINS in config.h
|
|
- To use the usart2 (USART2) pins,
|
|
- Connect the pins A2, A3 one to the other on each side
|
|
- Define USE_SDI2 in config.h
|