qmk_firmware/keyboards/smithrune/iron165r2
2022-08-20 11:34:17 +01:00
..
f072 Fixup iron165r2 (#17119) 2022-05-29 06:09:42 +01:00
f411 Swap over F4x1 8MHz HSE boards over from blackpill board files (#17520) 2022-07-01 15:36:08 +01:00
keymaps Refactor legacy quantum keycodes in default-ish keymaps (#17150) 2022-05-27 06:07:42 +10:00
config.h Move keyboard USB IDs and strings to data driven, pass 2: S-Y (#18093) 2022-08-20 01:48:38 +01:00
info.json Move keyboard USB IDs and strings to data driven, pass 2: S-Y (#18093) 2022-08-20 01:48:38 +01:00
iron165r2.c
iron165r2.h
readme.md RESET -> QK_BOOT keyboard readme (#18110) 2022-08-20 11:34:17 +01:00

Iron 165R2 QMK folder

Iron165R2

Introduction

This is the QMK Firmware repository for the Iron165 Round 2 PCB, a keyboard designed by Smith and Rune and PCB designed by Gondolindrim, who is also the firwmare maintainer.

The Iron 165R2 PCB is a 65% PCB with support for a myriad of alternative layouts, including a 7U bottom row and ISO. It also supports in-switch single-color LEDs and RGB LEDs for underglow light.

As of November 2021, the only way to obtain an Iron165 was through the Group Buy which is already over; extra units are still to be sold.

How to flash

Enter bootloader

The DFU state in the bootloader can be accessed in 3 ways:

  • Bootmagic reset: Hold down the key at (0,0) in the matrix (usually the top left key, escape in the default keymap) and plug in the keyboard;
  • Physical reset button: press the button on the front of the PCB, next to caps lock, for at least five seconds;
  • Keycode in layout: Press the key mapped to QK_BOOT; in the default layout, that is top left key ('escape') in layer 1.

How to compile and flash

The 165R2 PCB was prototyped and tested using two microcontrollers: STM32F072 and STM32F411. Most production-run units were manufactured with the latter.

After checking what PCB you own and setting up your build environment, you can compile the Iron 165R2 default keymap by using one of the options below.

make smithrune/iron165r2/f072:default
make smithrune/iron165r2/f411:default

And use dfu-util in the command line or through a GUI like QMK toolbox to upload the firmware to the PCB. To directly flash the PCB after it is put into a DFU state, use:

make smithrune/iron165r2/f072:default:flash
make smithrune/iron165r2/f411:default:flash

See the build environment setup and the make instructions for more information. Brand new to QMK? Start with our Complete Newbs Guide.

The "runes RGB" feature

The firmware for 165R2 allows the user to control the RGBs on the PCB through limiting their span according to the usage. There are four possible usages:

  • "Rune RGBs" where only the RGBs under the SnR rune logo on the 165R2 case are lit up; runergbs
  • "Line RGBs" where only the RGBs on the two alpha cluster rows are lit up; linergbs
  • "Luke RGBs" where the line RGBs and D25-D23 are on (to avoid hotspotting on the rune backplate); and lukergbs
  • "All RGBs" where all RGBs are turned on. allrgbs

In order to use the "rune RGBs" option, you can turn this option on by un-commenting the respective line on the corresponding config.h file:

#define RUNE_RGBS

If you want to use the "line RGBs" option, you can un-comment the respective lone on the corresponding config.h file:

#define LINES_RGBS

If you want to use the "luke RGBs" option, you can un-comment the respective lone on the corresponding config.h file:

#define LUKE_RGBS

The options supersede each other in this order. If no option is defined, then the firwmare defaults to the "all RGBs" option.