mirror of
https://github.com/qmk/qmk_firmware.git
synced 2024-12-25 02:49:55 +00:00
c61d7d7cb0
* Began Work On STM32 Ergodox Changes to be committed: new file: keyboards/ergodox_stm32/config.h new file: keyboards/ergodox_stm32/rules.mk * test * Now it compile. Not linking thou * Screw this Linker. It links now! * Blinkly Keyboard * bootloader test code * Working on matrix / i2c stuff * Progress (LED Blink) * Progress on MCP_23017 Status Flag * [WIP] * update * Works! Remeber to change back the bootloader address when the new bootloadrer is ready. * Time to go debug the i2c * Finally, it now works with PCB Rev 1.0.2 * updated for rev.2 pcb * minor compilation fix * Why when debugger is enabled then everything works. * Remeber to call init functions. * Update arm i2c driver to support STM32F103 series device. * fix include once header. Replaced with #pragma once. * complication test
143 lines
3.9 KiB
C
143 lines
3.9 KiB
C
/*
|
|
ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
|
|
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
|
you may not use this file except in compliance with the License.
|
|
You may obtain a copy of the License at
|
|
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
|
|
|
Unless required by applicable law or agreed to in writing, software
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
See the License for the specific language governing permissions and
|
|
limitations under the License.
|
|
*/
|
|
|
|
#ifndef _BOARD_H_
|
|
#define _BOARD_H_
|
|
|
|
/*
|
|
* Board identifier.
|
|
*/
|
|
#define BOARD_JM60
|
|
#define BOARD_NAME "ErgoDox STM32 Keyboard"
|
|
|
|
/*
|
|
* Board frequencies.
|
|
*/
|
|
#define STM32_LSECLK 0
|
|
#define STM32_HSECLK 8000000
|
|
|
|
/*
|
|
* MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
|
|
*
|
|
* Only xB (128KB Flash) is defined, but it's identical to the
|
|
* x8 version (64KB Flash) except for the Flash region size in the
|
|
* linker script. For x8 parts use xB here and change to the x8 linker
|
|
* script in the project Makefile.
|
|
*/
|
|
#define STM32F103xB
|
|
|
|
/*
|
|
* IO pins assignments
|
|
*
|
|
* numbering is sorted by onboard/connectors, as from the schematics in
|
|
* http://www.vcc-gnd.com/read.php?tid=369
|
|
*/
|
|
|
|
/* on-board */
|
|
#define GPIOA_USBDM 11 // pin 8
|
|
#define GPIOA_USBDP 12 // pin 9
|
|
|
|
#define GPIOC_OSC32_IN 14
|
|
#define GPIOC_OSC32_OUT 15
|
|
|
|
/*
|
|
* I/O ports initial setup, this configuration is established soon after reset
|
|
* in the initialization code.
|
|
*
|
|
* The digits have the following meaning:
|
|
* 0 - Analog input.
|
|
* 1 - Push Pull output 10MHz.
|
|
* 2 - Push Pull output 2MHz.
|
|
* 3 - Push Pull output 50MHz.
|
|
* 4 - Digital input.
|
|
* 5 - Open Drain output 10MHz.
|
|
* 6 - Open Drain output 2MHz.
|
|
* 7 - Open Drain output 50MHz.
|
|
* 8 - Digital input with PullUp or PullDown resistor depending on ODR.
|
|
* 9 - Alternate Push Pull output 10MHz.
|
|
* A - Alternate Push Pull output 2MHz.
|
|
* B - Alternate Push Pull output 50MHz.
|
|
* C - Reserved.
|
|
* D - Alternate Open Drain output 10MHz.
|
|
* E - Alternate Open Drain output 2MHz.
|
|
* F - Alternate Open Drain output 50MHz.
|
|
* Please refer to the STM32 Reference Manual for details.
|
|
*/
|
|
|
|
/*
|
|
* Port A setup.
|
|
* Everything input with pull-up except:
|
|
*/
|
|
#define VAL_GPIOACRL 0x88888888 /* PA7...PA0 */
|
|
#define VAL_GPIOACRH 0x88888888 /* PA15...PA8 */
|
|
#define VAL_GPIOAODR 0xFFFFFFFF
|
|
|
|
/*
|
|
* Port B setup.
|
|
* Everything input with pull-up except:
|
|
*/
|
|
#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */
|
|
#define VAL_GPIOBCRH 0x88888888 /* PB15...PB8 */
|
|
#define VAL_GPIOBODR 0xFFFFFFFF
|
|
|
|
/*
|
|
* Port C setup.
|
|
* Everything input with pull-up except:
|
|
*/
|
|
#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
|
|
#define VAL_GPIOCCRH 0x88888888 /* PC15...PC8 */
|
|
#define VAL_GPIOCODR 0xFFFFFFFF
|
|
|
|
/*
|
|
* Port D setup.
|
|
* Everything input with pull-up except:
|
|
* PD0 - Normal input (XTAL).
|
|
* PD1 - Normal input (XTAL).
|
|
*/
|
|
#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
|
|
#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
|
|
#define VAL_GPIODODR 0xFFFFFFFF
|
|
|
|
/*
|
|
* Port E setup.
|
|
* Everything input with pull-up except:
|
|
*/
|
|
#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
|
|
#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
|
|
#define VAL_GPIOEODR 0xFFFFFFFF
|
|
|
|
/*
|
|
* USB bus activation macro, required by the USB driver.
|
|
*/
|
|
#define usb_lld_connect_bus(usbp) /* always connected */
|
|
|
|
/*
|
|
* USB bus de-activation macro, required by the USB driver.
|
|
*/
|
|
#define usb_lld_disconnect_bus(usbp) /* always connected */
|
|
|
|
#if !defined(_FROM_ASM_)
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
void boardInit(void);
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
#endif /* _FROM_ASM_ */
|
|
|
|
#endif /* _BOARD_H_ */
|