mirror of
https://github.com/qmk/qmk_firmware.git
synced 2024-12-13 05:11:01 +00:00
ebb512db82
* Clean up `DEBOUNCE` in config.h, 0-9 * Clean up `DEBOUNCE` in config.h, A * Clean up `DEBOUNCE` in config.h, B * Clean up `DEBOUNCE` in config.h, C * Clean up `DEBOUNCE` in config.h, D * Clean up `DEBOUNCE` in config.h, E * Clean up `DEBOUNCE` in config.h, F * Clean up `DEBOUNCE` in config.h, G * Clean up `DEBOUNCE` in config.h, H * Clean up `DEBOUNCE` in config.h, handwired * Clean up `DEBOUNCE` in config.h, I * Clean up `DEBOUNCE` in config.h, J * Clean up `DEBOUNCE` in config.h, K * Clean up `DEBOUNCE` in config.h, L * Clean up `DEBOUNCE` in config.h, M * Clean up `DEBOUNCE` in config.h, N * Clean up `DEBOUNCE` in config.h, O * Clean up `DEBOUNCE` in config.h, P * Clean up `DEBOUNCE` in config.h, Q * Clean up `DEBOUNCE` in config.h, R * Clean up `DEBOUNCE` in config.h, S * Clean up `DEBOUNCE` in config.h, T * Clean up `DEBOUNCE` in config.h, U * Clean up `DEBOUNCE` in config.h, V * Clean up `DEBOUNCE` in config.h, W * Clean up `DEBOUNCE` in config.h, X * Clean up `DEBOUNCE` in config.h, Y * Clean up `DEBOUNCE` in config.h, Z * Remove default debounce from info.json * Migrate non-default debounce to info.json |
||
---|---|---|
.. | ||
keymaps | ||
lib | ||
config.h | ||
halconf.h | ||
info.json | ||
macropad.c | ||
macropad.h | ||
mcuconf.h | ||
readme.md | ||
rules.mk |
Adafruit MacroPad RP2040
A RP2040-powered Macropad with a 3x4 layout.
- Keyboard Maintainer: Jpe230
- Hardware Supported: Adafruit MacroPad RP2040
- Hardware Availability: Barebones kit Starter Kit
Make example for this board (after setting up your build environment):
qmk compile -kb adafruit/macropad -km default
See the build environment setup and the make instructions for more information. Brand new to QMK? Start with our Complete Newbs Guide.
Features
- Raspberry Pi RP2040 Chip + 8MB Flash memory - Dual-core Cortex M0+ at ~130MHz with 264KB of RAM.
- 3x4 Mechanical key switch sockets - accepts any Cherry MX-compatible switches. Individually tied to GPIO pins (not matrix wired)
- One NeoPixel RGB LED per switch, on north side.
- Rotary encoder, 20 detents per rotation, with push-switch on GPIO pin. Push switch is also used for entering bootloader mode when held down on power-up or reset.
- 128x64 SH1106 Monochrome OLED display - On high-speed hardware SPI port for quick updates.
- 8mm Speaker/Buzzer - With Class D amplifier and RC filter, can be used to make simple beeps and sounds effects. (Unsupported for now)
- STEMMA QT Connector - Allows adding any I2C sensors/displays/devices with plug-and-play cables.
- Reset button - On the side, for quick restarting, press it twice to enter bootloader.
- Four M3 mounting bosses - Make custom enclosures easily.
Bootloader
Enter the bootloader in 4 ways:
- Bootmagic reset: Hold down the key just below the rotary encoder push-button on power-up.
- Physical reset button: Press twice the button on the side while the board is connected.
- BOOT button Hold down the rotary encoder push-button on power-up or reset.
- Keycode in layout: Press the key mapped to
QK_BOOT
if it is available.