mirror of
https://github.com/qmk/qmk_firmware.git
synced 2024-11-23 20:03:01 +00:00
95001dd6e4
- change initialize of keyboard in matrix_scan() - keymap for 122 keys - Mafilefie and config.h for LUFA and PS/2 USART
114 lines
3.3 KiB
Makefile
114 lines
3.3 KiB
Makefile
# Target file name (without extension).
|
|
TARGET = terminal_lufa
|
|
|
|
# Directory common source filess exist
|
|
TOP_DIR = ../..
|
|
|
|
# Directory keyboard dependent files exist
|
|
TARGET_DIR = .
|
|
|
|
# keyboard dependent files
|
|
SRC = keymap.c \
|
|
matrix.c \
|
|
led.c
|
|
|
|
CONFIG_H = config.h
|
|
|
|
|
|
# MCU name, you MUST set this to match the board you are using
|
|
# type "make clean" after changing this, so all files will be rebuilt
|
|
#MCU = at90usb162 # Teensy 1.0
|
|
MCU = atmega32u4 # Teensy 2.0
|
|
#MCU = at90usb646 # Teensy++ 1.0
|
|
#MCU = at90usb1286 # Teensy++ 2.0
|
|
|
|
|
|
# Processor frequency.
|
|
# Normally the first thing your program should do is set the clock prescaler,
|
|
# so your program will run at the correct speed. You should also set this
|
|
# variable to same clock speed. The _delay_ms() macro uses this, and many
|
|
# examples use this variable to calculate timings. Do not add a "UL" here.
|
|
F_CPU = 16000000
|
|
|
|
|
|
#
|
|
# LUFA specific
|
|
#
|
|
# Target architecture (see library "Board Types" documentation).
|
|
ARCH = AVR8
|
|
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB = $(F_CPU)
|
|
|
|
# Interrupt driven control endpoint task
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
|
|
|
# Boot Section Size in bytes
|
|
# Teensy halfKay 512
|
|
# Atmel DFU loader 4096
|
|
# LUFA bootloader 4096
|
|
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
|
|
|
|
|
# Build Options
|
|
# comment out to disable the options.
|
|
#
|
|
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
|
#MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
|
#EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
|
CONSOLE_ENABLE = yes # Console for debug(+400)
|
|
COMMAND_ENABLE = yes # Commands for debug and configuration
|
|
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
|
|
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
|
|
|
|
|
|
#
|
|
# PS/2 protocol implementations
|
|
# USART is recommended if it is available, others are for reference purpose.
|
|
# INT implementation will drop simultaneous key strokes.
|
|
#
|
|
PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
|
|
#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
|
|
#PS2_USE_BUSYWAIT = yes # uses primitive reference code
|
|
|
|
ifdef PS2_USE_USART
|
|
SRC += protocol/ps2_usart.c
|
|
OPT_DEFS += -DPS2_USE_USART
|
|
endif
|
|
|
|
ifdef PS2_USE_INT
|
|
SRC += protocol/ps2.c
|
|
OPT_DEFS += -DPS2_USE_INT
|
|
endif
|
|
|
|
ifdef PS2_USE_BUSYWAIT
|
|
SRC += protocol/ps2.c
|
|
OPT_DEFS += -DPS2_USE_BUSYWAIT
|
|
endif
|
|
|
|
|
|
#---------------- Programming Options --------------------------
|
|
PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
|
|
|
|
|
|
# Search Path
|
|
VPATH += $(TARGET_DIR)
|
|
VPATH += $(TOP_DIR)
|
|
|
|
|
|
include $(TOP_DIR)/protocol/lufa.mk
|
|
include $(TOP_DIR)/protocol.mk
|
|
include $(TOP_DIR)/common.mk
|
|
include $(TOP_DIR)/rules.mk
|