mirror of
https://github.com/qmk/qmk_firmware.git
synced 2024-11-27 13:40:14 +00:00
e4ff07aff0
* Fix mixed tabs and spaces in adb_usb and m0110_usb makefiles * Fix typos in converter build options * Tweak ordering and spacing in converter makefiles
73 lines
2.8 KiB
Makefile
73 lines
2.8 KiB
Makefile
# MCU name
|
|
# atmega32u4 Teensy2.0
|
|
# atemga32u4 TMK Converter rev.1
|
|
# atemga32u2 TMK Converter rev.2
|
|
MCU = atmega32u4
|
|
|
|
# Processor frequency.
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
|
# automatically to create a 32-bit value in your source code.
|
|
#
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
|
# does not *change* the processor frequency - it should merely be updated to
|
|
# reflect the processor speed set externally so that the code can use accurate
|
|
# software delays.
|
|
#
|
|
F_CPU = 16000000
|
|
# F_CPU = 8000000
|
|
|
|
#
|
|
# LUFA specific
|
|
#
|
|
# Target architecture (see library "Board Types" documentation).
|
|
ARCH = AVR8
|
|
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB = $(F_CPU)
|
|
|
|
# Interrupt driven control endpoint task(+60)
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
|
# Bootloader
|
|
# This definition is optional, and if your keyboard supports multiple bootloaders of
|
|
# different sizes, comment this out, and the correct address will be loaded
|
|
# automatically (+60). See bootloader.mk for all options.
|
|
BOOTLOADER = caterina
|
|
|
|
# Boot Section Size in *bytes*
|
|
# Teensy halfKay 512
|
|
# Teensy++ halfKay 1024
|
|
# Atmel DFU loader 4096 for TMK Converter rev.1/rev.2
|
|
# LUFA bootloader 4096
|
|
# USBaspLoader 2048
|
|
|
|
# Build Options
|
|
# comment out to disable the options.
|
|
#
|
|
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
|
|
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
|
|
CONSOLE_ENABLE = no # Console for debug(+400)
|
|
COMMAND_ENABLE = no # Commands for debug and configuration
|
|
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
|
|
NKRO_ENABLE = no # USB Nkey Rollover - not yet supported in LUFA
|
|
EXTRAKEY_ENABLE = yes
|
|
USB_HID_ENABLE = yes
|
|
BACKLIGHT_ENABLE = no
|
|
#BLUETOOTH = AdafruitBLE # For Adafruit Feather 32U4 BLE support, uncomment this line
|
|
CUSTOM_MATRIX = yes
|
|
|
|
SRC = matrix.c adb.c led.c
|