* Add Per Key functionality for AutoShift (#11536)
* LED Matrix: Reactive effect buffers & advanced indicators (#12588)
* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)
* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)
* LED Matrix: Split (#12633)
* [CI] Format code according to conventions (#12650)
* feat: infinite timeout for leader key (#6580)
* feat: implement leader_no_timeout logic
* docs(leader_key): infinite leader timeout docs
* Format code according to conventions (#12680)
* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)
* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)
Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).
* Update ADC docs to match the actually used resolution
ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly. Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).
* Fix pinToMux() for B12 and B13 on STM32F3xx
Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.
* Add support for all possible analog pins on STM32F1xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families). Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).
Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.
* Add support for all possible analog pins on STM32F4xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.
Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.
Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.
* Fix STM32F3xx ADC mux table in documentation
The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).
* Add STM32F1xx ADC pins to the documentation
* Add STM32F4xx ADC pins to the documentation
* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)
* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.
* Update flashing.md
* Update chconf.h
* Update config.h
* Update halconf.h
* Update mcuconf.h
* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)
* Add support for MCU = STM32F446 (#12619)
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
* Format code according to conventions (#12682)
* Format code according to conventions (#12687)
* Add STM32L433 and L443 support (#12063)
* initial L433 commit
* change to XC
* fix L433
* disable all peripherals
* update system and peripheral clocks
* 433 change
* use its own board files
* revert its own board files
* l433 specific change
* fix stm32l432xx define
* remove duplicate #define
* fix bootloader jump
* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h
* move to L443
* move to L443
* fix sdmmc in mcuconf.h
* include STM32L443
* add L443
* Include L443 in compatible microcontrollers
* Include L443 in compatible microcontrollers
* Update config bootloader jump description
* Update ChibiOS define reasoning
* Update quantum/mcu_selection.mk
* fix git conflict
* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)
* Fix bad PR merge for #6580. (#12721)
* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)
* [CI] Format code according to conventions (#12731)
* Fixing transport's led/rgb matrix suspend state logic (#12770)
* [CI] Format code according to conventions (#12772)
* Fix comment parsing (#12750)
* Added OLED fade out support (#12086)
* fix some references to bin/qmk that slipped in (#12832)
* Resolve a number of warnings in `qmk generate-api` (#12833)
* New command: qmk console (#12828)
* stash poc
* stash
* tidy up implementation
* Tidy up slightly for review
* Tidy up slightly for review
* Bodge environment to make tests pass
* Refactor away from asyncio due to windows issues
* Filter devices
* align vid/pid printing
* Add hidapi to the installers
* start preparing for multiple hid_listeners
* udev rules for hid_listen
* refactor to move closer to end state
* very basic implementation of the threaded model
* refactor how vid/pid/index are supplied and parsed
* windows improvements
* read the report directly when usage page isn't available
* add per-device colors, the choice to show names or numbers, and refactor
* add timestamps
* Add support for showing bootloaders
* tweak the color for bootloaders
* Align bootloader disconnect with connect color
* add support for showing all bootloaders
* fix the pyusb check
* tweaks
* fix exception
* hide a stack trace behind -v
* add --no-bootloaders option
* add documentation for qmk console
* Apply suggestions from code review
* pyformat
* clean up and flesh out KNOWN_BOOTLOADERS
* Remove pointless SERIAL_LINK_ENABLE rules (#12846)
* Make Swap Hands use PROGMEM (#12284)
This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.
* Fix another bin/qmk reference (#12856)
* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)
* Fixup build errors on `develop` branch. (#12723)
* LED Matrix: Effects! (#12651)
* Fix syntax error when compiling for ARM (#12866)
* Remove KEYMAP and LAYOUT_kc (#12160)
* alias KEYMAP to LAYOUT
* remove KEYMAP and LAYOUT_kc
* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)
* Rename `point_t` -> `led_point_t` (#12864)
* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)
* Add missing LED Matrix suspend code to suspend.c (#12878)
* LED Matrix: Documentation (#12685)
* Deprecate `send_unicode_hex_string()` (#12602)
* Fix spelling mistake regarding LED Matrix in split_common. (#12888)
* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)
* Use milc.subcommand.config instead of qmk.cli.config (#12915)
* Use milc.subcommand.config instead
* pyformat
* remove the config test
* Add function to allow repeated blinking of one layer (#12237)
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Fixup housekeeping from being invoked twice per loop. (#12933)
* matrix: wait for row signal to go HIGH for every row (#12945)
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* ensure we do not conflict with existing keymap aliases (#12976)
* Add support for up to 4 IS31FL3733 drivers (#12342)
* Convert Encoder callbacks to be boolean functions (#12805)
* [Keyboard] Fix Terrazzo build failure (#12977)
* Do not hard set config in CPTC files (#11864)
* [Keyboard] Corne - Remove legacy revision support (#12226)
* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)
* Add Full-duplex serial driver for ARM boards (#9842)
* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)
* Backlight: add defines for default level and breathing state (#12560)
* Add dire message about LUFA mass storage bootloader (#13014)
* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)
Was causing compiler errors on some systems.
* Fix keyboards/keymaps for boolean encoder callback changes (#12985)
* `backlight.c`: include `eeprom.h` (#13024)
* Add changelog for 2021-05-29 Breaking Changes merge (#12939)
* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version
* Add recent develop changes
* Sort recent develop changes
* Remove sections for ChibiOS changes per tzarc
No ChibiOS changes this round.
* Add and sort recent develop changes
* add notes about keyboard moves/deletions
* import changelog for PR 12172
Documents the change to BOOTMAGIC_ENABLE.
* update section headings
* re-sort changelog
* add additional note regarding Bootmagic changes
* remove changelog timestamp
* update dates in main Breaking Changes docs
* fix broken section anchors in previous changelogs
* add link to backlight/eeprom patch to changelog
* highlight some more changes
* link PRs from section headers
* Restore standard readme
* run: qmk cformat --core-only
* Redo Arm DAC implementation for additive, wavetable synthesis, sample playback
changes by Jack Humbert on an implementation for DAC audio on arm/chibios platforms
this commits bundles the changes from the arm-dac-work branch focused on audio/audio_arm.* into one commit (leaving out the test-keyboard)
f52faeb5d (origin/arm-dac-work) add sample and wavetable examples, parsers for both
-> only the changes on audio_arm_.*, the keyboard related parts are split off to a separate commit
bfe468ef1 start morphing wavetable
474d100b5 refined a bit
208bee10f play_notes working
3e6478b0b start in-place documentation of dac settings
3e1826a33 fixed blip (rounding error), other waves, added key selection (left/right)
73853d651 5 voices at 44.1khz
dfb401b95 limit voices to working number
9632b3379 configuration for the ez
6241f3f3b notes working in a new way
* Redo Arm DAC implementation for additive, wavetable synthesis, sample playback
changes by Jack Humbert on an implementation for DAC audio on arm/chibios platforms
this commit splits off the plank example keymap from commit
f52faeb5d (origin/arm-dac-work) add sample and wavetable examples, parsers for both
* refactoring: rename audio_ to reflect their supported hardware-platform and audio-generation method: avr vs arm, and pwm vs dac
* refactoring: deducplicate ISR code to update the pwm duty-cycle and period in the avr-pwm-implementation
pulls three copies of the same code into one function
which should improve readability and maintainability :-)
* refactoring: move common code of arm and avr implementation into a separate/new file
* refactoring: audio_avr_pwm, renaming defines to decouple them from actually used timers, registers and ISRs
* refactoring: audio_avr_pwm - replacing function defines with plain register defines
aligns better with other existing qmk code (and the new audio_arm_pwm) doing similar pwm thing
* add audio-arm-pwm
since not all STM32 have a DAC onboard (STM32F2xx and STM32F3xx), pwm-audio is an alternative (STM32F1xx)
this code works on a "BluePill" clone, with an STM32F103C8B
* clang-format changes on quantum/audio/* only
* audio_arm_dac: stopping the notes caused screeching when using the DAC audio paths
* audio_arm_pwm: use pushpull on the pin; so that a piezzo can be hooked up direclty without additional components (opendrain would require an external pullup)
* refactoring: remove unused file from/for atmel-avr chips
* refactoring: remove unused (avr) wavetable file
* audio_arm_dac: adapt dac_end callback to changed chibios DAC api
the previous chibios (17.6.0) passed along a pointer into the buffer plus a sample_count (which are/already where included in the DACDrivre object) - the current chibios (19.1.0) only passes the driver object.
this patch ports more or less exactly what the previous chibios ISR code did: either have the user-callback work the first or second half of the buffer (dacsample_t pointer, with half the DAC_BUFFER_SIZE samples) by adjusting the pointer and sample count
* audio-arm-dac: show a compile-warning on undefined audio-pins
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* audio_arm_dac: switch from exemplary wavetable generation to sine only
sine+triangle+squrare is exemplary, and not realy fit for "production" use
'stairs' are usefull for debugging (hardware, with an oscilloscope)
* audio_arm_dac: enable output buffers in the STM32
to drive external loads without any additional ciruitry - external opamps and such
* audio: prevent out-of-bounds array access
* audio_arm_dac: add output-frequency correcting factor
* audio_arm_pwm: get both the alternate-function and pm-callback variants back into working condition
and do some code-cleanup, refine documentation, ...
* audio_arm_pwm: increase pwm frequency for "higher fidelity"
on the previous .frequency=100000 higher frequency musical notes came out wrong
(frequency measured on a Tektronix TDS2014B)
note | freq | arm-pwm
C2 | 65.4 | 65.491
C5 | 523.25 | 523.93
C6 | 1046.5 | 1053.38
C7 | 2093 | 2129
C8 | 4186 | 4350.91
with .frequency = 500000
C8 | 4186 | 4204.6
* audio refactoring: remove unused variables
* audio_arm_dac: calibrate note tempo: with a tempo of 60beats-per-second a whole-note should last for exactly one second
* audio: allow feature selection in rules.mk
so the user can switch the audio driver between DAC and PWM on STM32 boards which support both (STM32F2 and up)
or select the "pin alternate" pwm mode, for example on STM32F103
* audio-refactoring: move codeblocks in audio.[ch] into more coherent groups
and add some inline documentation
* audio-refactoring: cleanup and streamline common code between audio_arm_[dac|pwm]
untangeling the relation between audio.c and the two drivers
and adding more documenting comments :-)
* audio_avr_pwm: getting it back into working condition, and cleanup+refactor
* audio-refactoring: documentation and typo fixes
Co-Authored-By: Nick Brassel <nick@tzarc.org>
* audio-refactoring: cleanup defines, inludes and remove debug-prints
* audio_chibios_dac: define&use a minimal sampling rate, based on the available tone-range
to ease up on the cpu-load, while still rendering the higher notes/tones sufficiently
also reenable the lower tones, since with the new implementation there is no evidence of them still beeing 'bugged'
* audio-refactoring: one common AUDIO_MAX_VOICES define for all audio-drivers
* audio-chibios-pwm: pwm-pin-allternate: make the the timer, timer-channel and alternate function user-#definable
* audio_chibios_dac: math.h has fmod for this
* Redo Arm DAC implementation for additive, wavetable synthesis, sample playback
update Jack Humberts dac-example keymaps for the slight changes in the audio-dac interface
* audio-refactoring: use a common AUDIO_PIN configuration switch instead of defines
have the user select a pin by configuration in rules.mk instead of a define in config.h
has the advantage of beeing in a common form/pattern across all audio-driver implementations
* audio-refactoring: switch backlight_avr.c to the new AUDIO_PIN defines
* audio-common: have advance_note return a boolean if the note changed, to the next one in the melody beeing played
* audio-chibios-pwm: fix issue with ~130ms silence between note/frequency changes while playing a SONG
through trial,error and a scope/logic analyzer figured out Chibios-PWMDriver (at least in the current version) misbehaves if the initial period is set to zero (or one; two seems to work); when thats the case subsequent calls to 'pwmChhangePeriod' + pwmEnableChannel took ~135ms of silence, before the PWM continued with the new frequency...
* audio-refactoring: get 'play_note' working again
with a limited number of available voices (say AUDIO_VOICES_MAX=1) allow new frequencies to be played, by discarding the oldest one in the 'frequencies' queue
* audio: set the fallback driver to DAC for chibios and PWM for all others (==avr at the moment)
* audio-refactoring: moore documentation
and some cleanup
* audio-avr-pwm: no fallback on unset AUDIO_PIN
this seems to be the expected behaviour by some keyboards (looking at ckeys/handwire_101:default) which otherwise fail to build because the firmware-image ends up beeing too large for the atmega... so we fail silently instead to keep travis happy
* audio-refactoring: untangling terminology: voice->tone
the code actually was working on tones (combination of pitch/frequency, duration, timbre, intensity/volume) and not voices (characteristic sound of an instrument; think piano vs guitar, which can be played together, each having its own "track" = voice on a music sheet)
* audio-pwm: allow freq=0 aka a pause/rest in a SONG
continue processing, but do not enable pwm units, since freq=0 wouldn't produce any sound anyway (and lead to division by zero on that occasion)
* audio-refactoring: audio_advance_note -> audio_advance_state
since it does not only affect 'one note', but the internally kept state as a whole
* audio-refactoring: untangling terminology: polyphony
the feature om the "inherited" avr code has little to do with polyphony (see wikipedia), but is more a time-multiplexing feature, to work around hardware limitations - like only having one pwm channel, that could on its own only reproduce one voice/instrument at a time
* audio-chibios-dac: add zero-crossing feature
have tones only change/stop when the waveform approaches zero - to avoid audible clicks
note that this also requires the samples to start at zero, since the internally kept index into the samples is reset to zero too
* audio-refactoring: feature: time-multiplexing of tones on a single output channel
this feature was in the original avr-pwm implementation misnomed as "polyphony"
with polyphony_rate and so on; did the same thing though: time-multiplexing multiple active notes so that a single output channel could reproduce more than one note at a time (which is not the same as a polyphony - see wikipedia :-) )
* audio-avr-pwm: get music-mode working (again) on AVRs
with both pwm channels, or either one of the two :-)
play_notes worked already - but music_mode uses play_note
* audio-refactoring: split define MAX_SIMULTANEOUS_TONES -> TONE_STACKSIZE
since the two cases are independant from one another, the hardware might impose limitations on the number of simultaneously reproducable tones, but the audio state should be able to track an unrelated number of notes recently started by play_note
* audio-arm-dac: per define selectable sample-luts
plus generation script in ./util
* audio-refactoring: heh, avr has a MIN...
* audio-refactoring: add basic dac audio-driver based on the current/master implementation
whereas current=d96380e65496912e0f68e6531565f4b45efd1623
which is the state of things before this whole audio-refactoring branch
boiled down to interface with the refactored audio system = removing all
redundant state-managing and frequency calculation
* audio-refactoring: rename audio-drivers to driver_$PLATFORM_$DRIVER
* audio-arm-pwm: split the software/hardware implementations into separate files
which saves us partially from a 'define hell', with the tradeoff that now two somewhat similar chibios_pwm implementations have to be maintained
* audio-refactoring: update documentation
* audio-arm-dac: apply AUDIO_PIN defines to driver_chibios_dac_basic
* audio-arm-dac: dac_additive: stop the hardware when the last sample completed
the audio system calls for a driver_stop, which is delayed until the current sample conversion finishes
* audio-refactoring: make function-namespace consistent
- all (public) audio functions start with audio_
- also refactoring play*_notes/tones to play*_melody, to visually distance it a bit from play*_tone/_note
* audio-refactoring: consistent define namespace: DAC_ -> AUDIO_DAC_
* audio-arm-dac: update (inline) documentation regarding MAX for sample values
* audio-chibios-dac: remove zero-crossing feature
didn't quite work as intended anyway, and stopping the hardware on close-to-zero seems to be enought anyway
* audio-arm-dac: dac_basic: respect the configured sample-rate
* audio-arm-pwm: have 'note_timbre' influence the pwm-duty cycle
like it already does in the avr implementation
* audio-refactoring: get VIBRATO working (again)
with all drivers (verified with chibios_[dac|pwm])
* audio-arm-dac: zero-crossing feature (Mk II)
wait for the generated waveform to approach 'zero' before either turning off the output+timer or switching to the current set of active_tones
* audio-refactoring: re-add note-resting -> introduce short_rest inbetween
- introduce a short pause/rest between two notes of the same frequency, to separate them audibly
- also updating the refactoring comments
* audio-refactoring: cleanup refactoring remnants
remove the former avr-isr code block - since all its features are now refactored into the different parts of the current system
also updates the TODOS
* audio-refactoring: reserve negative numbers as unitialized frequencies
to allow the valid tone/frequency f=0Hz == rest/pause
* audio-refactoring: FIX: first note of melody was missing
the first note was missing because 'goto_next_note'=false overrode a state_change=true of the initial play_tone
and some code-indentations/cleanup of related parts
* audio-arm-dac: fix hardware init-click
due to wron .init= value
* audio-refactoring: new conveniance function: audio_play_click
which can be used to further refactor/remove fauxclicky (avr only) and/or the 'clicky' features
* audio-refactoring: clang-format on quantum/audio/*
* audio-avr-pwm: consecutive notes of the same frequency get a pause inserted inbetween by audio.c
* audio-refactoring: use milliseconds instead of seconds for 'click' parameters
clicks are supposed to be short, seconds make little sense
* audio-refactoring: use timer ticks instead of counters
local counters were used in the original (avr)ISR to advance an index into the lookup tables (for vibrato), and something similar was used for the tone-multiplexing feature
decoupling these from the (possibly irregular) calls to advance_state made sesne, since those counters/lookups need to be in relation to a wall-time anyway
* audio-refactoring: voices.c: drop 'envelope_index' counter in favour of timer ticks
* audio-refactoring: move vibrato and timbre related parts from audio.c to voices.c
also drops the now (globally) unused AUDIO_VIBRATO/AUDIO_ENABLE_VIBRATO defines
* audio.c: use system-ticks instead of counters the drivers have to take care of for the internal state posision
since there already is a system-tick with ms resolution, keeping count separatly with each driver implementation makes little sense; especially since they had to take special care to call audio_advance_state with the correct step/end parameters for the audio state to advance regularly and with the correct pace
* audio.c: stop notes after new ones have been started
avoids brief states of with no notes playing that would otherwise stop the hardware and might lead to clicks
* audio.c: bugfix: actually play a pause
instead of just idling/stopping which lead the pwm drivers to stop entirely...
* audio-arm-pwm: pwm-software: add inverted output
new define AUDIO_PIN_ALT_AS_NEGATIVE will generate an inverted signal on the alternate pin, which boosts the volume if a piezo is connected to both AUDIO_PIN and AUDIO_PIN_ALT
* audio-arm-dac: basic: handle piezo configured&wired to both audio pins
* audio-refactoring: docs: update for AUDIO_PIN_ALT_AS_NEGATIVE and piezo wiring
* audio.c: bugfix: use timer_elapsed32 instad of keeping timestamps
avoids running into issues when the uint32 of the timer overflows
* audio-refactoring: add 'pragma once' and remove deprecated NOTE_REST
* audio_arm_dac: basic: add missing bracket
* audio.c: fix delta calculation
was in the wrong place, needs to use the 'last_timestamp' before it was reset
* audio-refactoring: buildfix: wrong legacy macro for set_timbre
* audio.c: 16bit timerstamps suffice
* audio-refactoring: separate includes for AVR and chibios
* audio-refactoring: timbre: use uint8 instead of float
* audio-refactoring: duration: use uint16 for internal per-tone/note state
* audio-refactoring: tonemultiplexing: use uint16 instead of float
* audio-arm-dac: additive: set second pin output-low
used when a piezo is connected to AUDIO_PIN and AUDIO_PIN_ALT, with PIN_ALT_AS_NEGATIVE
* audio-refactoring: move AUDIO_PIN selection from rules.mk to config.h
to be consistent with how other features are handled in QMK
* audio-refactoring: buildfix: wrong legacy macro for set_tempo
* audio-arm-dac: additive: set second pin output-low -- FIXUP
* audio.c: do duration<>ms conversion in uint instead of float
on AVR, to save a couple of bytes in the firmware size
* audio-refactoring: cleanup eeprom defines/usage
for ARM, avr is handled automagically through the avr libc and common_features.mk
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* audio.h: throw an error if OFF is larger than MAX
* audio-arm-dac: basic: actually stop the dac-conversion on a audio_driver_stop
to put the output pin in a known state == AUDIO_DAC_OFF_VALUE, instead of just leaving them where the last conversion was... with AUDIO_PIN_ALT_AS_NEGATIVE this meant one output was left HIGH while the other was left LOW
one CAVEAT: due to this change the opposing squarewave when using both A4 and A5 with AUDIO_PIN_ALT_AS_NEGATIVE
show extra pulses at the beginning/end on one of the outputs, the two waveforms are in sync otherwise.
the extra pusles probably matter little, since this is no high-fidelity sound generation :P
* audio-arm-dac: additive: move zero-crossing code out of dac_value_generate
which is/should be user-overridable == simple, and doing one thing: providing sample values
state-transitions necessary for the zero crossing are better handled in the surrounding loop in the dac_end callback
* audio-arm-dac: dac-additive: zero-crossing: ramping up or down
after a start trigger ramp up: generate values until zero=OFF_VALUE is reached, then continue normally
same in reverse for strop trigger: output values until zero is reached/crossed, then keep OFF_VALUE on the output
* audio-arm-dac: dac-additive: BUGFIX: return OFF_VALUE when a pause is playing
fixes a bug during SONG playback, which suddenly stopped when it encoutnered a pause
* audio-arm-dac: set a sensible default for AUDIO_DAC_VALUE_OFF
1/2 MAX was probably exemplary, can't think of a setup where that would make sense :-P
* audio-arm-dac: update synth_sample/_wavetable for new pin-defines
* audio-arm-dac: default for AUDIO_DAC_VALUE_OFF
turned out that zero or max are bad default choices:
when multiple tones are played (>>5) and released at the same time (!), due to the complex waveform never reaching 'zero' the output can take quite a while to reach zero, and hence the zero-crossing code only "releases" the output waaay to late
* audio-arm-dac: additive: use DAC for negative pin
instead of PAL, which only allows the pin to be configured as output; LOW or HIGH
* audio-arm-dac: more compile-time configuration checks
* audio-refactoring: typo fixed
* audio-refactoring: clang-format on quantum/audio/*
* audio-avr-pwm: add defines for B-pin as primary/only speaker
also updates documentation.
* audio-refactoring: update documentation with proton-c config.h example
* audio-refactoring: move glissando (TODO) to voices.c
refactored/saved from the original glissando implementation in then upstream-master:audio_avr.c
still needs some work though, as it is now the calculation *should* work, but the start-frequency needs to be tracked somewhere/somehow; not only during a SONG playback but also with user input?
* audio-refactoring: cleanup: one round of aspell -c
* audio-avr-pwm: back to AUDIO_PIN
since config_common.h expands them to plain integers, the AUDIO_PIN define can directly be compared to e.g. B5
so there is no need to deal with separate defines like AUDIO_PIN_B5
* audio-refactoring: add technical documentation audio_driver.md
which moves some in-code documentation there
* audio-arm-dac: move AUDIO_PIN checks into c-code
instead of doing everything with the preprocessor, since A4/A5 do not expand to simple integers, preprocessor int-comparison is not possible. but necessary to get a consistent configuration scheme going throughout the audio-code... solution: let c-code handle the different AUDIO_PIN configurations instead (and leave code/size optimizations to the compiler)
* audio-arm-dac: compile-fix: set AUDIO_PIN if unset
workaround to get the build going again, and be backwarts compatible to arm-keyboards which not yet set the AUDIO_PIN define. until the define is enforced through an '#error"
* audio-refactoring: document tone-multiplexing feature
* audio-refactoring: Apply suggestions from documentation review
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* audio-refactoring: Update docs/audio_driver.md
* audio-refactoring: docs: fix markdown newlines
Terminating a line in Markdown with <space>-<space>-<linebreak> creates an HTML single-line break (<br>).
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* audio-arm-dac: additive: fix AUDIO_PIN_ALT handling
* audio-arm-pwm: align define naming with other drivers
Co-authored-by: Joel Challis <git@zvecr.com>
* audio-refactoring: set detault tempo to 120
and add documentation for the override
* audio-refactoring: update backlight define checks to new AUDIO_PIN names
* audio-refactoring: reworking PWM related defines
to be more consistent with other QMK code
Co-authored-by: Joel Challis <git@zvecr.com>
* audio-arm: have the state-update-timer user configurable
defaulting to GPTD6 or GPTD8 for stm32f2+ (=proton-c)
stm32f1 might need to set this to GPTD4, since 6 and 8 are not available
* audio-refactoring: PLAY_NOTE_ARRAY was already removed in master
* Add prototype for startup
* Update chibiOS dac basic to disable pins on stop
* Add defaults for Proton C
* avoid hanging audio if note is completely missed
* Don't redefine pins if they're already defined
* Define A4 and A5 for CTPC support
* Add license headers to keymap files
* Remove figlet? comments
* Add DAC config to audio driver docs
* Apply suggestions from code review
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* Add license header to py files
* correct license header
* Add JohSchneider's name to modified files
AKA credit where credit's due
* Set executable permission and change interpeter
* Add 'wave' to pip requirements
* Improve documentation
* Add some settings I missed
* Strip AUDIO_DRIVER to parse the name correctly
* fix depreciated
* Update util/audio_generate_dac_lut.py
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* Fix type in clueboard config
* Apply suggestions from tzarc
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Johannes <you@example.com>
Co-authored-by: JohSchneider <JohSchneider@googlemail.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joshua Diamond <josh@windowoffire.com>
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* enable LTO for smaller firmware size
* delete since this was added to userspace rules.mk
* readme updates and new images
* Add -j to compile and flash commands in userpsace
* Enable NKRO
* Enable NKRO, VIA, LTO by default
* Stanrc85-ansi readme update
* Stanrc85-alice readme
* quick RGB layer indicator fix in keymap
* Don't block keys during startup animation
* More refinements related to startup and debug state
* restore key logging
* some cleanup on scan rate reporting
* trim some fat
* better lighting to indicate jumped to bootloader
* use eeprom for state restoration
* a little reorganization
* report version immediately when turn on debug
* hold-to-adjust for hue, sat, val
* cformat
* reorg rules.mk settings, fix compile with CONSOLE_ENABLE=no
* simplify spidey3 userspace
* NULL in layer list caused buggy behavior
* more bugfix
* update numpad layout to match matt30 MT3 /dev/tty keycaps
* swap emdash and endash
* map shift+backspace to delete
* removing NO_ACTION_ONSHOT makes the firmware SMALLER ?!
* cformat
* improve spi_glow
* disable shift-backspace = delete by default
* Initial support for Durgod K320 with BootMagic Lite
- Adding missing files
- Add Unicode Map Support & new user keymap
- Remove personalized features from Default keymap
- Added Unicode Map to both Default and kuenhlee keymap.c
- Updated readme.md
- Added additional Fn Shortcut keys
* Additional support for Durgod K320
- Simplifying default keymap
- Renaming durgod_k320 => durgod/k320
- Removing copy of ST_NUCLEO64_F070RB from K320. Replacing with local board.h
- Adding Mac keyboard layout for K320 as alternative via Fn+F12
- Implementing Windows Key lock on K320
- Cleaning up duplicated core functionality
- Adding default_toggle_mac_windows keymap with:
- Ability to toggle between Windows and MacOS layout
- Mac Media Lock functionality.
* Updating K320 keymap readme
Co-authored-by: kuenhlee <eos.camera.lee@gmail.com>
* Update other keyboards for rgb matrix changes
* Remove customized bootmagic code
* Fix corne layout compilation error
* Fix compiler errors with all keymaps
* Add Simple Visualizer for ergodox infinity
* Fix compile issue with Corne
* Fix keymap stuff
* Add alias for mouse layer
* Add Halmak Keyboard layout
* Updates for Kyria
* Add support for oled interval
* Change RGB stuff
[CHANGE] Fix coexistence issues
* Fix rgb_stuff
* Add custom ploopyco mouse keymap
* Decrease default dwell time
* Updates based on last breaking changes update
* Disable command on dactyl
* Update ergodox to use proper commands for rgb matrix indicators
* Update all rgb matrix indicator functions
* Update rules for dactyl-manuform
* Reduce wait time for mouse layer off event
* Add more info to logger
* Add wrappers for get_tapping term
* Move version.h include into only file that actually needs it
* Update rgb sleep stuff
* Update key print function
* Change DM keymap settings
* Change pin for DM Manuform
* Add Proton C stuff for Corne keymap
* more arm corne tinkering
* Even more arm stuff for corne
* Cleanup corne stuff
* redirect default keymap to drashna
because I am a very bad man
* change corne rgb priority
* Update tractyl manuform to not conflict
* Add more secret stuff
* more dactyl tweaks
* Add more options to split transport
* Changes of oled support
* Change split settings
* Improve keylogger formatting more
* tweak oled stuff
* Oled and such tweaks
* Reduce brightness due to leds
* Decrease brightness more
* Only run layer code if master
* Initial commit for my Corne keyboard layout.
* Updates to Corne, etc.
Finished working on primary layout for Corne keyboard.
Cleaned up some comments for my 4x12 Ortho layout.
* Changes for crkbd layout
* Fixed the config.h to reflect using ee_hands
* Added RGB configs to crkbd/corne layout
Co-authored-by: Ian Sterling <503326@MC02YT9K9LVCF.tld>
* Reset everything to upstream, reapply Bocaj changes
* Bocaj - address PR comments
* Just in time changes
* Bocaj - Several adjustments after using the layout for a while
* Add LAYOUT_alice support: fallacy
* Add LAYOUT_alice support: kb_elmo/sesame
* Add LAYOUT_alice support: cheshire/curiosity
* Add LAYOUT_alice support: evyd13/wonderland
* Add LAYOUT_alice support: mechlovin/adelais
* Update LAYOUT_alice support: projectkb/alice
The PR that added Alice community layout support for the projectkb/alice/rev2 simultaneously broke support for every other keyboard that supported LAYOUT_alice.
This commit partially reverts the offending PR. `LAYOUT_alice` for the projectkb/alice has been renamed to `LAYOUT_alice_split_bs`, and a correct 65-key `LAYOUT_alice` has been added.
Additionally, the `LAYOUTS` rule has been moved to keyboard level as the layout macros are shared between rev1 and rev2 boards, which means the layout options are the same for both revisions.
* Update ramonimbao/aelith info.json
Keyboard source was already correct to support LAYOUT_alice, but the layout tree was missing from info.json.
* Fork `alice` Community Layout...
... into Standard and Split Backspace versions
Also updates stanrc85's layout keymap to use 65 keys instead of the Split Backspace 66-key version.
* Update LAYOUT_alice support: sneakbox/aliceclone
Rework the sneakbox/aliceclone to use the Split Backspace Alice layout.
* Update LAYOUT_alice support: zoo/wampus
The layout macro that was `LAYOUT_alice` was 66 keys. This layout macro has been renamed to `LAYOUT_alice_split_bs`, and a 65-key `LAYOUT_alice` has been added.
Additionally, the 66-key macro has been rearranged to accept its keycodes in the intended order for Community Layout support.
* Update keyboards for `LAYOUT_alice_split_bs` support
* LAYOUT_alice_split_bs support: ergosaurus
* LAYOUT_alice_split_bs support: handwired/colorlice
* LAYOUT_alice(_split_bs) support: handwired/owlet60
* LAYOUT_alice_split_bs support: nightly_boards/alter/rev1
* LAYOUT_alice(_split_bs) support: sck/osa
* LAYOUT_alice_split_bs support: tgr/alice
* LAYOUT_alice(_split_bs) support: tkc/osav2
* LAYOUT_alice_split_bs support: xelus/valor/rev1
* Branch point for 2020 November 28 Breaking Change
* Remove matrix_col_t to allow MATRIX_ROWS > 32 (#10183)
* Add support for soft serial to ATmega32U2 (#10204)
* Change MIDI velocity implementation to allow direct control of velocity value (#9940)
* Add ability to build a subset of all keyboards based on platform.
* Actually use eeprom_driver_init().
* Make bootloader_jump weak for ChibiOS. (#10417)
* Joystick 16-bit support (#10439)
* Per-encoder resolutions (#10259)
* Share button state from mousekey to pointing_device (#10179)
* Add hotfix for chibios keyboards not wake (#10088)
* Add advanced/efficient RGB Matrix Indicators (#8564)
* Naming change.
* Support for STM32 GPIOF,G,H,I,J,K (#10206)
* Add milc as a dependency and remove the installed milc (#10563)
* ChibiOS upgrade: early init conversions (#10214)
* ChibiOS upgrade: configuration file migrator (#9952)
* Haptic and solenoid cleanup (#9700)
* XD75 cleanup (#10524)
* OLED display update interval support (#10388)
* Add definition based on currently-selected serial driver. (#10716)
* New feature: Retro Tapping per key (#10622)
* Allow for modification of output RGB values when using rgblight/rgb_matrix. (#10638)
* Add housekeeping task callbacks so that keyboards/keymaps are capable of executing code for each main loop iteration. (#10530)
* Rescale both ChibiOS and AVR backlighting.
* Reduce Helix keyboard build variation (#8669)
* Minor change to behavior allowing display updates to continue between task ticks (#10750)
* Some GPIO manipulations in matrix.c change to atomic. (#10491)
* qmk cformat (#10767)
* [Keyboard] Update the Speedo firmware for v3.0 (#10657)
* Maartenwut/Maarten namechange to evyd13/Evy (#10274)
* [quantum] combine repeated lines of code (#10837)
* Add step sequencer feature (#9703)
* aeboards/ext65 refactor (#10820)
* Refactor xelus/dawn60 for Rev2 later (#10584)
* add DEBUG_MATRIX_SCAN_RATE_ENABLE to common_features.mk (#10824)
* [Core] Added `add_oneshot_mods` & `del_oneshot_mods` (#10549)
* update chibios os usb for the otg driver (#8893)
* Remove HD44780 References, Part 4 (#10735)
* [Keyboard] Add Valor FRL TKL (+refactor) (#10512)
* Fix cursor position bug in oled_write_raw functions (#10800)
* Fixup version.h writing when using SKIP_VERSION=yes (#10972)
* Allow for certain code in the codebase assuming length of string. (#10974)
* Add AT90USB support for serial.c (#10706)
* Auto shift: support repeats and early registration (#9826)
* Rename ledmatrix.h to match .c file (#7949)
* Split RGB_MATRIX_ENABLE into _ENABLE and _DRIVER (#10231)
* Split LED_MATRIX_ENABLE into _ENABLE and _DRIVER (#10840)
* Merge point for 2020 Nov 28 Breaking Change
* Refactor the crkbd/via keymap and fix OLED bugs
* Revert "Refactor the crkbd/via keymap and fix OLED bugs"
This reverts commit dc9db029fc.
* Fix OLED display bugs
* Remove unused functions
* Remove uncessary the key logger
* Add new lines at end of file
* Remove unnecesary extern for is_master
* Remove extern is_master from rev1.h
* Remove ssd1306 from common dir because its the legacy lib
* Update default keymap based the via keymap
* Remove foostan keymap because it will be legacy
* Revert Remove unnecesary extern for is_master
* Remove unnecessary backslashes.
* Minor Tweak
* Refactor spacebar defines.
* Add TMO50 layout
* Rename Atreus keymap.
* Refactor Atreus for readability.
* Eliminate tapdance quote and tweak maltroff.
* Factor out tapdance.
* Add some fancy combos and keys.
* Remove combos for now because they cause pain.
* WIP visualizer
* Alternate method for reset
* WIP2 visualizer
* Layer text tweak.
* Add made-up layout Nortron as a combination of Norman and Maltron.
* Add backspace.
* Add Talljoe keymap to Prime E.
* Fix double-colon so it doesn't press enter if shift is released early.
* Use new make command.
* Bring some modern standards into code and add licenses.
* Remove QMK_KEYBOARD_CONFIG_H and fixup QMK_KEYBOARD_H.
* Move from `biton32` to `get_highest_layer`.
* Remove PREVENT_STUCK_MODIFIERS
* Update keyboards/thevankeyboards/minivan/keymaps/talljoe-minivan/config.h
Add Eco keymap, factor Crkbd keymap to community layout, other minor tweaks
* Remove outdated Crkbd Ctrl key positioning info
* Add Left Alt key to Lily58 keymap
* Lily58 no longer overrides default TAPPING_TERM
* Refactor Crkbd keymap to use new community layout
* Fix underglow animations for Crkbd w/ Split Common
* Add initial Eco keymap
* Update outdated reference to Crkbd layout
* Add keymap links to userspace readme
* Add copyright notices to files changed in this PR
* add 65_ansi_split_bs to default community layouts
* Update layouts/default/65_ansi_split_bs/layout.json
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* my alice community layout
* add LAYOUT_alice support to projectkb/alice/rev2
* add addition BSPC key to default layout
* add define to support LAYOUT_default
* Add Launchpad keymap
Note: RGB and Audio won't work when using B pins for audio
* Add support for rgb matrix on launchpad
* Update config for launchpag
* Disable wait on layer change
* Update config for ErgoDox EZ
* Fixup rgb light userspace code
* Move Corne layout to community layouts folder
* Update config for corne to support community layouts
* Add license header to files
* Minor cleanup of userspace config
* Update Pimironi Trackball code
* Increase debounce time on ergodox
* Fix keymap handling
* Enable wait for USB for moonlander
* Update/add license headers
* fix review issues
* Added LAYOUT_alice
* Added fauxpark's suggestions as well as updating keymap graphic
* Added file header and used noroadleft's fix to the info.json for fast input mode
* Move my custom functions and keymaps to userspace to be able to add the STM32F411 variant of my keyboard with mostly the same functionality
* Move keymaps to community layouts
* Remove keymaps from userspace readme.md
Co-authored-by: Janos Daniel Reibl <janos.daniel.reibl@protonmail.com>
* First pass at manuform layout.
* Updates from actual usage on my board. Fixed a couple of bugs, added a stormlight quote randomizer.
* Use a 32-bit timer that can actually hit 5 minutes.
* Some updates after a day of usage:
* Turn off WPM. It's too inaccurate and takes up a decent amount of space that can be devoted to quotes.
* Turn off the OLEDs after 5 minutes
* Move the keys around a bit.
* Add many more quotes.
* Adjust the quotes to make room for missing and misswritten WoT quote. Adjusted the keymap slightly. Adjust the mods display to include one_shots.
* Revert osm on lgui as it makes start menu search impossible to use.
* Use LTO_ENABLE flag.
* License all of my (333fred's) keymaps as MIT.
* Update users/333fred/rgb.c
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
OLED Display fixes
Add support for RGBLIGHT Layers
Add gaming layer to corn and kyria
RGBLight Startup Animation fixes and improvements (uses matrix_scan now!)
Pimoroni Trackball support added (IT'S RGB!!!)
Fix issues due to code changes
* Add Chrome OS specific keys to 75_ansi/spidey3
* Clean up duplicative settings in rules.mk
* Refactor spidey3 userspace to use rgb layer blink
* Blink green on wakeup
* Improve _FN layer indicator
* Glyph transformation modes: wide, script, fraktur, and enclosed characters
* Add spider unicode glyph
* Fix compile error when NO_ACTION_ONESHOT
* Add a few more emoji
* Further refinement of lighting layer usage
* Fix reversed yes/no ack
* Lighting layers override RGB off
* Fix missing wide and incorrect script numbers
* Add LOL and surprise emoji
* Add missing break in switch statement
* Trim firmware size
* Use usage ID definitions in report.h
* Some minor whitespace cleanup
* Disable some unused features to reduce firmware size
* Print version on startup
* Seed rand() on first keystroke
* Add a key to immediately sleep CrOS
* Switch to Bootmagic Lite
* Trim down firmware size a little bit more
* Make RGBLIGHT_MODE_TWINKLE+4 my default
* Scan rate debug / fix version printing
Delay printing version on startup (console may not be ready)
Better scan rate reporting
* Disable locking caps, etc. to save more space
* Enable LTO
* Better seed for rand()
* Set MAX_LAYER for some performance improvement
* Another scan rate improvement
* Set manufacturer
* New startup animation
* Add GUI lock for F-keys (for CrOS)
* Add visual indication for glyph replacement and F-keys GUI lock
* Some cleanup; run cformat on spidey3 userspace
* Cycle between debug verbosity options
* Fix disable RGB Lighting after wakeup on Mac
* Branch point for 2020 May 30 Breaking Change
* Migrate `ACTION_LAYER_TOGGLE` to `TG()` (#8954)
* Migrate `ACTION_MODS_ONESHOT` to `OSM()` (#8957)
* Migrate `ACTION_DEFAULT_LAYER_SET` to `DF()` (#8958)
* Migrate `ACTION_LAYER_MODS` to `LM()` (#8959)
* Migrate `ACTION_MODS_TAP_KEY` to `MT()` (#8968)
* Convert V-USB usbdrv to a submodule (#8321)
* Unify Tap Hold functions and documentation (#8348)
* Changing board names to prevent confusion (#8412)
* Move the Keyboardio Model01 to a keyboardio/ subdir (#8499)
* Move spaceman keyboards (#8830)
* Migrate miscellaneous `fn_actions` entries (#8977)
* Migrate `ACTION_MODS_KEY` to chained mod keycodes (#8979)
* Organizing my keyboards (plaid, tartan, ergoinu) (#8537)
* Refactor Lily58 to use split_common (#6260)
* Refactor zinc to use split_common (#7114)
* Add a message if bin/qmk doesn't work (#9000)
* Fix conflicting types for 'tfp_printf' (#8269)
* Fixed RGB_DISABLE_AFTER_TIMEOUT to be seconds based & small internals cleanup (#6480)
* Refactor and updates to TKC1800 code (#8472)
* Switch to qmk forks for everything (#9019)
* audio refactor: replace deprecated PLAY_NOTE_ARRAY (#8484)
* Audio enable corrections (2/3) (#8903)
* Split HHKB to ANSI and JP layouts and Add VIA support for each (#8582)
* Audio enable corrections (Part 4) (#8974)
* Fix typo from PR7114 (#9171)
* Augment future branch Changelogs (#8978)
* Revert "Branch point for 2020 May 30 Breaking Change"
* initial commit for tsangan_hhkb community layout
* keymap.c done
* wrote readme
* move media keys; add shortcuts
* edit to reflect changes in keymap
* update readme with imgur link
* Community layout support for KBD67 hotswap
* Community layout support for KBD67 rev1
* Community layout support for KBD67 rev2
* Move bcat's KBD67 hotswap layout to community
* Move menu key on ergo boards to match staggered
* Unify 60_tsangan_hhkb and 60_ansi_split_bs_rshift
* Sync KBD67, Quefrency with community layouts
* Update ergo KLE images
* Update community layout KLE images
* Update KLE images/descriptions for remaining keebs
* Add 65 ANSI Blocker Split BS default layout
- Add new 65 ANSI Blocker Split BS layout as many 65 ANSI Blocker layouts also support split backspace
* Add 65 ANSI Blocker Tsangan default layout
- Add new 65 ANSI Blocker Tsangan layout as many 65 ANSI Blocker layouts also support a split backspace and a 7u bottom row configuration.
* Fix file names
* Fix 65_ansi_blocker_tsangan keymap
* Fix 65_ansi_blocker_split_bs alignment
* Fix readme name for 65_ansi_blocker_split_bs
* Change 65_ansi_blocker_tsangan to 2u backspace
* Change spaces in preview to NBSP
* Change more spaces in preview to NBSP (right-alt)
* Give Tsangan layout a real Fn2 layer
* Disable mouse keys to work around qmk#8323
I don't actually use this feature, so there's no reason for it to be
enabled anyway, and it seems to cause spurious wakeups on Windows.
* First cut at Josh Diamond's KBD75 customizations.
Includes:
* My unique keymap with ChromeOS specific keys
* Use RGB underglow to indicate Caps Lock
* Some unicode bindings
* Some changes to make debugging easier
* Updated spidey3 to be applicable to all 75_ansi boards
* Sadly, ChromeOS doesn't pay attention to most consumer codes
* Add mac layer; fix flakeyness in CAPS_LOCK underglow.
* Make layers.json match the keymap (to the extent possible)
* Major cleanup; fix broken debug persistence
* Cleanup some whitespace issues
* Fix incorrect log message.
* Rework layer indication to user RGBLIGHT_LAYERS
* Update layouts/community/75_ansi/spidey3/keymap.c
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Rename users/spidey3/rgblight.c to layer_rgb.c per suggestion
* Refactor to use set_single_persistant_default_layer().
* Use dprint/f to make logging more elegant.
* Update users/spidey3/config.h
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Update users/spidey3/config.h
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Update layouts/community/75_ansi/spidey3/rules.mk
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update users/spidey3/spidey3.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update users/spidey3/layer_rgb.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update users/spidey3/init.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Changes from code review
* Numpad layer, various keys for 75_ansi/spidey3
* Add Fn-B to toggle NKRO
* Blink rgb to acknowledge some setting changes
* Updated media control & reset key location
* Minor cleanup
Co-authored-by: Joshua Diamond <jdiamond@Deep-Thought.local>
Co-authored-by: Drashna Jaelre <drashna@live.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
