* Fix RGB heatmap to use XY positions
* lower effect area limit and make configurable
* tidy up macro
* Fix triggering in both directions.
* add docs
* fix bug when decreasing value
* performance tweak
* Add GET_TAPPING_TERM macro to reduce duplicate code
The macro gives the right tapping term depending on whether per-key
tapping terms and/or dynamic tapping terms are enabled. Unnecessary
function calls and variable resolution are avoided.
Fixes#16472.
* Use GET_TAPPING_TERM for Cirque trackpads
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
* Install dependencies before executing unit tests.
* Split out UTF-8 decoder.
* Fixup python formatting rules.
* Add documentation for QGF/QFF and the RLE format used.
* Add CLI commands for converting images and fonts.
* Add stub rules.mk for QP.
* Add stream type.
* Add base driver and comms interfaces.
* Add support for SPI, SPI+D/C comms drivers.
* Include <qp.h> when enabled.
* Add base support for SPI+D/C+RST panels, as well as concrete implementation of ST7789.
* Add support for GC9A01.
* Add support for ILI9341.
* Add support for ILI9163.
* Add support for SSD1351.
* Implement qp_setpixel, including pixdata buffer management.
* Implement qp_line.
* Implement qp_rect.
* Implement qp_circle.
* Implement qp_ellipse.
* Implement palette interpolation.
* Allow for streams to work with either flash or RAM.
* Image loading.
* Font loading.
* QGF palette loading.
* Progressive decoder of pixel data supporting Raw+RLE, 1-,2-,4-,8-bpp monochrome and palette-based images.
* Image drawing.
* Animations.
* Font rendering.
* Check against 256 colours, dump out the loaded palette if debugging enabled.
* Fix build.
* AVR is not the intended audience.
* `qmk format-c`
* Generation fix.
* First batch of docs.
* More docs and examples.
* Review comments.
* Public API documentation.
* [Docs] Include ASCII diagram to explain tap-hold modes
* [Docs]: add examples for Default mode for Tap Hold
* [Docs] fix some wrong explanation in tap_hold.md
Fixes compilation issues when bluetooth is enabled, due to issues
with cpp used by bluetooth code.
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Drashna Jaelre <drashna@live.com>
* docs: clarify in "Keymap Overview" what LAYOUT is and isn't
It is not strictly necessary to use LAYOUT macros in keyboard.c, but it
is a convenient abstraction of hardware internals, allowing focus on the
physical keyboard layout.
From the C source point of view LAYOUT is macro with a parameter list,
which expands to a array of rows that each is an array with a keyboard
scancode for each column. A macro parameter list is not an array, and
even less a single array.
Perhaps no big deal, but also no reason to give incorrect hints.
* docs: update "Understanding QMK's Code" to current code structure introduced in 96e2b13d1d
This part of the documentation was no longer correct. I tried updating
it, mainly copy editing and using github links to latest release.
This is not trying to fix all problems, but just trying to fix some
problems while reusing much of the old phrases and structure.
* Update docs to use "qmk format-python"
* Add example implementations for compatible MCUs list
* Update docs/compatible_microcontrollers.md
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Recommend the use of functions instead of keycodes
* Commit suggested review
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Recommend the use of functions instead of keycodes
* Commit suggested revision
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Add layer key indicator example
* Update description
* Deobfuscate with index variable
* Add missing layer variable
* Correct color name and indicator function
* Function typo
* Place layer variable outside loops to save firmware space
Co-authored-by: filterpaper <filterpaper@localhost>
* Update feature_macros.md
Added a link to the usage of SAFE_RANGE as this wasn't clear to me when I visited this page in isolation.
* Fix typo
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Draft implementation
* formatting
* fix combined buttons
* remove pimoroni throttle
* sync pointing on a throttle loop with checksum
* no longer used
* doh
Co-authored-by: Drashna Jaelre <drashna@live.com>
* switch pimoroni to a cpi equivalent
* add cpi support
* allow user modification of seperate mouse reports
* a little tidy up
* add *_RIGHT defines.
* docs
* doxygen comments
* basic changelog
* clean up pimoroni
* small doc fixes
* Update docs/feature_pointing_device.md
Co-authored-by: Drashna Jaelre <drashna@live.com>
* performance tweak if side has usb
* Don't run init funtions on wrong side
* renamed some variables for consistency
* fix pimoroni typos
* Clamp instead of OR
* Promote combined values to uint16_t
* Update pointing_device.c
Co-authored-by: Drashna Jaelre <drashna@live.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Add open-drain GPIO support.
* `qmk format-c`
* Wording.
* Remove port GPIO implementations as the only board that uses it has its own internal defs anyway. Will wait for first-class handling of ports in core before reimplementing.
* Changelog.
* Remove the asymmetric encoder PR from listing due to revert.
* More docs
* More docs
* More docs
* Links to changelog, updated schedule, slotted in 2 weeks of testing at the end so that there's no ambiguity with PR merge dates.
* Clarify keyboard moves.
* Fix dates
* Sidebar
* Fixup dates.
* Fixup dates.
* Wording.
* New feature: `DYNAMIC_TAPPING_TERM_ENABLE`
3 new quantum keys to configure the tapping term on the fly.
* Replace sprintf call in tapping_term_report by get_u16_str
* Replace tab with 4 spaces
* Add ifndef to WS2812 timing constraints
Due to the way that the PrimeKB Meridian PCB was designed, this change
is needed in order to properly adjust the LEDs.
Testing:
* Compiled primekb/meridian:default successfully
* Compiled random board (walletburner/neuron:default) successfully
* Fix linting errors
Missed some spacing
* More linting fixes
Spacing on the comments... really?
* Rename WS2812 timing parameters for clarity; add comments
* Add docs update for the WS2812 timing macros
* Fix typo on comment
* Add ifndef for WS2812_RES
* Update double backticks and table with parameters
* Move timing adjustments documentation to ws2812_drivers
* Move timings adjustment discussion to bitbang section
* Update T0H and T1H definitions in subtractions
* format
Co-authored-by: Gondolindrim <alvaro.volpato@usp.br>
Co-authored-by: zvecr <git@zvecr.com>
* [Docs] Squeezing space out of AVR
* Add more info
* Apply suggestions from code review
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Add oled section
* Apply suggestions from code review
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Update layers and intro wording
* Rename doc file
* add get_u8_str support
* oled clarifications
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* macros in json keymaps
* add advanced macro support to json
* add a note about escaping macro strings
* add simple examples
* format json
* add support for language specific keymap extras
* switch to dictionaries instead of inline text for macros
* use SS_TAP on the innermost tap keycode
* add the new macro format to the schema
* document the macro limit
* add the json keyword for syntax highlighting
* fix format that vscode screwed up
* Update feature_macros.md
* add tests for macros
* change ding to beep
* add json support for SENDSTRING_BELL
* update doc based on feedback from sigprof
* document host_layout
* remove unused var
* improve carriage return handling
* support tab characters as well
* Update docs/feature_macros.md
Co-authored-by: Nick Brassel <nick@tzarc.org>
* escape backslash characters
* format
* flake8
* Update quantum/quantum_keycodes.h
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Reimplements WPM feature.
- Now calculates exact WPM over the last up to three seconds of typing.
- WPM_SMOOTHING removed, as it's no longer needed.
- WPM_SAMPLE_SECONDS added, to specify how long a period to average WPM
over, set to 5 seconds by default.
- WPM_SAMPLE_PERIODS added, to specify how many sampling buffers we'll
use. Each one uses one extra byte of space. Having more will lead
to smoother decay of WPM values. Defaults to 50 (we're saving so
many bytes of firmware space I felt like being extravagent, and this
change is still a big size saving overall)
- WPM_UNFILTERED option added (defaults to unset), which disables all
filtering within the WPM feature. This saves some space in the
firmware and also reduces latency between typing and the WPM
calculation measuring it. (saves 70 bytes in my tests)
- WPM_LAUNCH_CONTROL added (defaults to unset). When typing begins
while the current displayed WPM value is zero, the WPM calculation
only considers the time elapsed since typing began, not the whole
WPM_SAMPLE_SECONDS buffer. The result of this is that the displayed
WPM value much more rapidly reaches an accurate WPM value, even when
results are being filtered. (costs 22 bytes in my tests)
- Updates documentation to reflect changed options.
Saves about 900 bytes, in my tests, compared against the previous implementation,
with default settings.
* Apply suggestions from code review
Co-authored-by: Sergey Vlasov <sigprof@gmail.com>
Co-authored-by: Trevor Powell <trevor@vectorstorm.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Sergey Vlasov <sigprof@gmail.com>
* CLI: Add 'cd' subcommand
Go to your qmk_firmware dir with ease.
* Fix for Windows and do not run if already under QMK Home
* Make flake8 happy
* Fix prompt for Windows
* Make flake8 happy once again
* I'll get it right eventually
* Apply suggestions from code review
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add subcommand to __init__.py and fixup after rebase
* Update Windows code to use milc's run
* Unify the subshell starting with os.execl
* Exit with error msg when output is redirected to non-TTY.
* Revert Windows-specific code
Co-authored-by: Ryan <fauxpark@gmail.com>
* Use copy_tree from distutils for python 3.7 support
* Bump python version in docs
* Changed new-keyboard to use printf-style format strings
* Use username for manunfacturer / maintainer
* Update lib/python/qmk/cli/new/keyboard.py
Co-authored-by: Zach White <skullydazed@drpepper.org>
Co-authored-by: Zach White <skullydazed@drpepper.org>
* Add support for building against ChibiOS svn/trunk.
* Swap to 21.6.x
* Update to latest branch revision as released version is broken.
* Updated configs.
* Conf updates.
* Updated ChibiOS
* Convert STM32L422 to actual L422 ChibiOS platform.
* Downgrade to 20.3.4 as ChibiOS 21.6.x is being aborted.
* Rollback L422-based boards.
This also add support for specifying a LED pin to indicate haptic status,
and also adds support for a haptic-enable pin, which is useful to turn off
the boost converter on the solenoid driver.
* Initial work for de-ghost enable
* Dumb mistake with the redefine
* Added Copywrite stuff on source files
* Fixed whitespace errors
* Added support for all ISSI LED drivers
* Updated docs for support for ISSI LED driver pull-up pull-down
* Applied clang format
* Added 'boolean' flag to enable de-ghosting for the is31fl3731 IC
* Fixed some of the grammer in the docs
* Fixed comment placement and grammer of comment
* Fixed whitespace errors from lint
Co-authored-by: donicrosby <donicrosby1995@gmail.com>
* Gets RGB working on a split keyboard with IS31FL3733. Currently needs small tweak to re-enable WS2812
* Added helper function
* Trying to integrate the function
* Moved functionality into a macro
* Swapped conditional for a macro everywhere
* Tidying up
* More code cleanup
* Documentation updates
* Fixed formatting via linter
* Switching to a function from a macro
* Fixed compile error
* Fixing WS2812 behavior. UNTESTED.
* Updated documentation about the driver addresses.
* Fixed code for WS2812
* Trying to add in LED_MATRIX support
* Updated effects for LED matrix
* Updated third-party effect defines.
* Ran format-c on modified files
* Apply suggestions from code review
Co-authored-by: Ryan <fauxpark@gmail.com>
* Move to static inline. Avoids issues with gcc v8+
* Move helper function for LED_matrix to static inline to avoid issues with gcc v8+
Co-authored-by: Vlad Kvitnevskiy <vladkvit@outlook.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add support for RISC-V builds and GD32VF103 MCU
* Add toolchain selection in chibios.mk based on the mcu selected in
mcu_selection.mk
* Reorder and added comments to chibios.mk to have a streamlined makefile
* Add GD32VF103 mcu to possible targets for QMK.
* Add STM32 compatibility for GD32VF103 MCU, this is hacky but more efficent
then rewriting every driver.
* Add GigaDevice DFU bootloader as flash target, please note that
dfu-util of at least version 0.10 is needed.
* Add analog driver compatibility
* Add apa102 bitbang driver compatibility
* Add ws2812 bitbang driver compatibility
* Add eeprom in flash emulation compatibility
* Allow faster re-builds with ccache
* Add SiPeed Longan Nano to platform files
* Add SiPeed Longan Nano Onekeys
* Make quine compatible with other bootloaders
* Support builds with picolibc
* Add risc-v toolchain to arch and debian/ubuntu scripts
* GPIO functions are no longer in quantum.h
* Update docs/internals_gpio_control.md
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Remove SERIAL_LINK
* more stale paths in doxygen-todo
* Fix
* More refs
* Update testing docs
* Update doxygen-todo
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* update pr_checklist.md translation
* update file based on comments
* add id on feature_led_indicators.md and update text based on comments
* update file based on comments
* update file based on comment
* pulled source from dev branch
* missed a file from origin
* formatting
* revised argument names. relaxed matching rules to work for avr too
* add docstrings
* added docs. tightened up regex
* remove unused imports
* cleaning up command file. use existing qmk dir constant
* rename parser library file
* move lib functions into command file. there are only 2 and they aren't large
* currently debugging...
* more robustly find config
* updated docs
* remove unused imports
* reuse make executable from the main make command
* pulled source from dev branch
* missed a file from origin
* formatting
* revised argument names. relaxed matching rules to work for avr too
* add docstrings
* added docs. tightened up regex
* remove unused imports
* cleaning up command file. use existing qmk dir constant
* rename parser library file
* move lib functions into command file. there are only 2 and they aren't large
* currently debugging...
* more robustly find config
* updated docs
* remove unused imports
* reuse make executable from the main make command
* remove MAKEFLAGS from environment for better control over process management
* Update .gitignore
Co-authored-by: Michael Forster <forster@google.com>
* add a usage line to docs
* doc change as suggested
Co-authored-by: Nick Brassel <nick@tzarc.org>
* rename command
* remove debug print statements
* generate-compilation-database: fix arg handling
* generate-comilation-db: improve error handling
* use cli.run() instead of Popen()
Co-authored-by: Xton <cdewan@apple.com>
Co-authored-by: Christon DeWan <cmdpix@mac.com>
Co-authored-by: Michael Forster <forster@google.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
changed line 21 from saying "three steps" to "two steps" as there are only two steps
Co-authored-by: feynmantf <46390109+feynmantf@users.noreply.github.com>
* Align ChibiOS I2C defs with other drivers
* Update keyboards/xelus/valor_frl_tkl/config.h
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* add 'include keyboard_features.mk' into build_keyboard.mk
keyboard_features.mk is a keyboard-local version of the functions performed by common_features.mk.
* add comment into build_keyboard.mk
* added description of keyboard_features.mk in hardware_keyboard_guidelines.md.
* rename `keyboard_features.mk` to `post_rules.mk`
* adding uf2 flash support for blackpill 401
* forgot to add blackpill to keyboard header file
* making changes requested by drashna
* fixing tzarc s comments
* removing the keyboard
* undo the change to dactyl_manuform.h
* Make solo half of split keyboards (more) usable.
Using only one half of a split keyboard (that's using the split_common
framework to communicate) is not a great experience, since several read
timeouts per scan cycle cause an unusably slow scan rate.
This change blocks all split communication attempts for 500 ms
(configurable) after an error occurs, causing the scan rate to become at
least _more_ usable, but might need some tweaking to work fully on most
keyboards. One read timeout still needs to occur after the 500 ms has
passed, and if that timeout isn't low enough, some scan cycles may still
be too slow.
* Fix lint complaint.
* Require 25 consecutive comm errors to see comms as disconnected.
The number of max errors can be overridden by defining
`SPLIT_MAX_CONNECTION_ERRORS`.
* Add comments to new defines, and ability to disable disconnection check.
Also increase `SPLIT_MAX_CONNECTION_ERRORS` to 40, since it's divisible
by most relevant numbers for the description.
* Make lint happy ...again
* Only update `connection_check_timer` when needed.
* Add new defines to split keyboard documentation.
* Move connection timeout logic to transport.c, add `is_transport_connected`.
* Use split_common disconnection logic in matrix.c.
Instead of doing more or less the same thing twice.
* Move disconnection logic to `transport_master`.
Is a cleaner implementation, and causes the scan rate while disconnected
to increase instead of decrease.
* Lint fixes.
* Lower default `SERIAL_USART_TIMEOUT` to 20 ms.
The read timeout must be low enough to not cause exessively long scan
cycles when using a solo split half. 10 ms was determined from testing
to work fine even with the slowest defined baudrate of 19200 (5 ms was
too low for that case), so 20 ms should be fine for most cases.
* Remove `SERIAL_USART_TIMEOUT` from ergodox_infinity/config.h
Was somewhat mistakenly included in an earlier PR.
* Fix building with `USE_I2C`.
* Reduce built firmware size.
Not really sure why this works, the idea was taken from tzarc's work on
split disconnection.
* Tweak and improve opt-out for split disconnection logic.
There are now two ways to opt out from this feature:
* Set `SPLIT_MAX_CONNECTION_ERRORS` to 0. This will completely disable
the connection status checks (also affects the slave matrix reset logic in
matrix.c, though).
* Set `SPLIT_CONNECTION_CHECK_TIMEOUT` to 0. This will only disable the
communication throttling while disconnected. Will make the firmware
smaller.
* Make split disconnection logic work with custom transports.
Includes a fallback implementation for keyboards using a custom
split_util.c but not a custom matrix.c (currently no such keyboard seems
to be merged, though).
* Remove unnecessary include of timer.h
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Remove hysteresis on 4x encoders
Sometimes, controller skips encoder pulses and when it returns to default position, the encoder_pulses variable isn't equals 0. And when I turn encoder in opposite direciton, it skips first click becase of encoder_pulses crosses zero. To prevent this, I add the ENCODER_DEFAULT_POS constant, and reset encoder_pulses into 0 when the state variable equals ENCODER_DEFAULT_POS.
* Documentation for ENCODER_DEFAULT_POS
* Add digitizer HID interface for setting the mouse cursor position at
absolute screen coordinates. Tested on Pro Micro, Proton C and
Blackpill.
* Update docs/feature_digitizer.md
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add missing copyrights
Add V-USB support
* Add support for digitizer dedicated endpoint for lufa and chibios.
Fix formatting issues
Move digitizer_task definition to the feature's base implementation file
* Run cformat on modified files
* Change digitizer report usage to Digitizer instead of Pen to avoid
pointer disappearing on Windows.
* Update tmk_core/protocol/vusb/vusb.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Run cformat from docker image
* Remove send_digitizer from host_driver_t and instead rely on the
declaration being the interface to the implementation in each
HW-specific usb implementation.
* Fix build : send_digitizer shouldn't be static in vusb and add
weak-linkage implementation for tests without usb implementation
* Change digitizer user interface to match pointing device's
* Update documentation with new API
Co-authored-by: a-chol <nothing@none.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Change animations to require explicet activation
* Add support for legacy config
* Make default for now
* Add LED Matrix support
* change LED Matrix docs
* Enable sync of OLED/ST7565 display on/off state on Splits
* Only send if states are not matched
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* new keyboard: handwired/directpins
* fix promicro keyboard_name
* add teensy2 and teensy2++ support
* align with handwired/onekey
* tweak pids
* add teensy 3.2 and teensy lc to directpins
* move directpins from handwired to ez_maker
* add docs for easy maker
* Architecture documentation for the configurator and api
* Apply suggestions from code review
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* disambiguate Bootmagic rules in keymaps
The files edited by this commit were added at a point in time where `BOOTMAGIC_ENABLE = yes` enabled full Bootmagic.
This commit edits the files to specify that full Bootmagic is intended.
* remove BOOTMAGIC_ENABLE=full setting
* unify commented BOOTMAGIC_ENABLE rules in keyboards
Explicitly sets `BOOTMAGIC_ENABLE = no` in keyboards where the rule was commented out.
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;#[ \t]*\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-zA-Z]\+\).*;\1 = no # Virtual DIP switch configuration;g' {} +
```
* remove commented Bootmagic rules from keymap/user level
Command:
```
find keyboards/ layouts/ users/ -type f -name 'rules.mk' -exec sed -i -e '/#.*\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*/d' {} +
```
* update keyboard BOOTMAGIC_ENABLE rule formatting
Sets the formatting of BOOTMAGIC_ENABLE rules to `BOOTMAGIC_ENABLE = [value]`, without the inline comments (which will be replaced later).
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
```
* update keyboards' BOOTMAGIC_ENABLE settings
Updates keyboard `rules.mk` files to use `BOOTMAGIC_ENABLE = lite` where `BOOTMAGIC_ENABLE = full` was being used.
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = \)full;\1lite;g' '{}' +
```
* update keymap/user BOOTMAGIC_ENABLE settings
Updates keymap/user `rules.mk` files to use `BOOTMAGIC_ENABLE = lite` where `BOOTMAGIC_ENABLE = full` was being used.
Commands:
```
find keyboards/ -type f -name 'rules.mk' -and -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE[ \t=]\+\)full;\1lite;g' '{}' +
find layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE[ \t=]\+\)full;\1lite;g' '{}' +
```
* remove and replace inline comments in keyboards and keymap/user files
Removes and replaces the inline comments, which have been updated to read `Enable Bootmagic Lite`.
Commands:
```
find keyboards/ -type f -name 'rules.mk' -and -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
find layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = lite\);\1 # Enable Bootmagic Lite;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = yes\);\1 # Enable Bootmagic Lite;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = no\);\1 # Enable Bootmagic Lite;g' '{}' +
```
* rename improperly named makefiles
Some files intended to be used as makefiles had improper names causing them to not be used as intended when building.
This commit corrects the filenames of the affected files.
* update renamed file with new rule formatting
* update QMK's template files
Updates QMK's `rules.mk` templates to use the new inline comment.
* update QMK Docs
- remove documentation of full Bootmagic
- update links to Bootmagic Lite doc
- add doc for Magic Keycodes
* rules.mk patch for coarse/ixora and coarse/vinta
* Add HOLD_ON_OTHER_KEY_PRESS option for dual-role keys
Implement an additional option for dual-role keys which converts the
dual-role key press into a hold action immediately when another key is
pressed (this is different from the existing PERMISSIVE_HOLD option,
which selects the hold action when another key is tapped (pressed and
then released) while the dual-role key is pressed). The Mod-Tap keys
already behave in a similar way, unless the IGNORE_MOD_TAP_INTERRUPT
option is enabled (but with some additional delays); the added option
makes this behavior available for all other kinds of dual-role keys.
* [Docs] Update tap-hold docs for HOLD_ON_OTHER_KEY_PRESS
Document the newly added HOLD_ON_OTHER_KEY_PRESS option and update the
documentation for closely related options (PERMISSIVE_HOLD and
IGNORE_MOD_TAP_INTERRUPT).
Use Layer Tap instead of Mod Tap in examples for PERMISSIVE_HOLD and
HOLD_ON_OTHER_KEY_PRESS, because the effect of using these options with
Mod Tap keys is mostly invisible without IGNORE_MOD_TAP_INTERRUPT.
Add comments before return statements in sample implementations of
`get_ignore_mod_tap_interrupt()`, `get_hold_on_other_key_press()` and
`get_permissive_hold()`.
Thanks to @Erovia and @precondition for comments and suggestions to
improve the documentation.
* Combo processing improvements.
Now it is possible to use ModTap and LayerTap keys as part of combos.
Overlapping combos also don't trigger all the combos, just exactly the
one that you press.
New settings:
- COMBO_MUST_HOLD_MODS
- COMBO_MOD_TERM
- COMBO_TERM_PER_COMBO
- COMBO_MUST_HOLD_PER_COMBO
- COMBO_STRICT_TIMER
- COMBO_NO_TIMER
* Remove the size flags from combo_t struct boolean members.
This in the end actually saves space as the members are accessed so many
times. The amount of operations needed to access the bits uses more
memory than setting the size saves.
* Fix `process_combo_key_release` not called correctly with tap-only combos
* Fix not passing a pointer when NO_ACTION_TAPPING is defined.
* Docs for `COMBO_ONLY_FROM_LAYER`
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Update quantum/process_keycode/process_combo.c
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Add `EXTRA_SHORT_COMBOS` option.
Stuff combo's `disabled` and `active` flags into `state`. Possibly can
save some space.
* Add more examples and clarify things with dict management system.
- Simple examples now has a combo that has modifiers included.
- The slightly more advanced examples now are actually more advanced
instead of just `tap_code16(<modded-keycode>)`.
- Added a note that `COMBO_ACTION`s are not needed anymore as you can
just use custom keycodes.
- Added a note that the `g/keymap_combo.h` macros use the
`process_combo_event` function and that it is not usable in one's
keymap afterwards.
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Change "the" combo action example to "email" example.
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Fix sneaky infinite loop with `combo_disable()`
No need to call `dump_key_buffer` when disabling combos because the
buffer is either being dumped if a combo-key was pressed, or the buffer is empty
if a non-combo-key is pressed.
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
Co-authored-by: Drashna Jaelre <drashna@live.com>
* ps2_mouse on ARM: an interrupt-version of the ps2-mouse code ported to ARM/chibios
* ps2_mouse on ARM: link EXT callback-channel selection to the user defined PS2_LINE_CLOCK
* ps2_mouse on ARM: replace DELAY_X defines with hardware-agnostic wait_X
* ps2_mouse on ARM: replace chibios-specific defines for the pins/lines with defines from quantum/config_common.h
and drop the '_LINE' component from teh define name
* ps2_mouse on ARM: expose the software-intterupt port as a user editable define
* Update docs/feature_ps2_mouse.md
Co-Authored-By: Hugo van Kemenade <hugovk@users.noreply.github.com>
* Update feature_ps2_mouse.md
* use a define to deduce the PS_DATA_PORT instead
* reduce all-zero extcfg to oneliner
* ps2_mouse: use generic wait instead of avr-delay
* Update docs/feature_ps2_mouse.md
* ps2_mouse: changes for new chibios version
(17.6.0 -> 19.1.0)
replacing the legacy externa-interrupt driver with pal-callbacks
* ps2_mouse: use PLATFORM_KEY
Co-Authored-By: Joel Challis <git@zvecr.com>
* ps2_mouse: clang-format corrections
* ps2_mouse: add systemlocks
using the chibios equivalent to AVRs cli: chSys[Unl|L]ock
Co-authored-by: Johannes <you@example.com>
Co-authored-by: Hugo van Kemenade <hugovk@users.noreply.github.com>
Co-authored-by: Joel Challis <git@zvecr.com>
This change fixes the warning caused by deprecated way of configuring terminal profiles.
The warning caused by old settings.json is the following:
This is deprecated, the new recommended way to configure your default shell is by creating a terminal profile in `#terminal.integrated.profiles.windows#` and setting its profile name as the default in `#terminal.integrated.defaultProfile.windows#`. This will currently take priority over the new profiles settings but that will change in the future.
Refer to the link below for more information:
https://code.visualstudio.com/docs/editor/integrated-terminal#_configuration
Added a `default` case in `switch(ql_tap_state.state)` at line 493 and 494.
Without it compile firmware with Example 6 code will encounter 2 errors:
`enumeration value 'TD_NONE' not handled in switch`
`enumeration value 'TD_UNKNOWN' not handled in switch`
PR #13296 changed the name of the `cformat` and `pyformat` commands to
`format-c` and `format-py` respectively. This PR updates the documentation
and some parts of the CLI to use the new names.
Also add documentation for the new `format-text` subcommand, introduced
in the same PR.
Currently, this feature isn't supported on splits, spent about an hour troubleshooting my board and firmware before asking, and turns out it's not in place. Note added to save others from this in the future.
* Updated docs/ja/proton_c_conversion.md original tag.
* Updated docs/ja/other_vscode.md original tag.
* Updated docs/ja/feature_swap_hands.md original tag.
* Updated docs/ja/faq_general.md original tag.
* Updated docs/ja/feature_userspace.md original tag.
* Updated git co docs/ja/config_options.md original tag.
* added support for inverting the hand pin for split keyboards
* Added docs about SPLIT_HAND_LOW_IS_LEFT
* Update docs/feature_split_keyboard.md
bring #define for split hand pin low for left half name in line with grid pin define
Co-authored-by: Joel Challis <git@zvecr.com>
* Update quantum/split_common/split_util.c
update split hand pin low is left name to match split hand grid define
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Unite half-duplex and full-duplex serial driver.
* Add full duplex operation mode to the interrupt based driver
* Delete DMA UART based full duplex driver
* The new driver targets #11930
* Fix freezes with failing transactions in half-duplex
* Increase default serial TX/RX buffer size to 128 bytes
* Correctly use bool instead of size_t
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Updated docs/ja/how_a_matrix_works.md original tag.
* Updated docs/ja/api_overview.md original tag.
* Updated docs/ja/contributing.md original tag
* Updated docs/ja/coding_conventions_c.md original tag
* Updated docs/ja/reference_configurator_support.md original tag
* Updated docs/ja/reference_glossary.md original tag
* Updated docs/ja/api_docs.md original tag
* Updated docs/ja/feature_stenography.md original tag
* Updated docs/ja/documentation_templates.md original tag
* Updated docs/ja/faq_keymap.md original tag
* Updated docs/ja/understanding_qmk.md original tag
* Extensible split data sync capability through transactions.
- Split common transport has been split up between the transport layer
and data layer.
- Split "transactions" model used, with convergence between I2C and
serial data definitions.
- Slave matrix "generation count" is used to determine if the full slave
matrix needs to be retrieved.
- Encoders get the same "generation count" treatment.
- All other blocks of data are synchronised when a change is detected.
- All transmissions have a globally-configurable deadline before a
transmission is forced (`FORCED_SYNC_THROTTLE_MS`, default 100ms).
- Added atomicity for all core-synced data, preventing partial updates
- Added retries to AVR i2c_master's i2c_start, to minimise the number of
failed transactions when interrupts are disabled on the slave due to
atomicity checks.
- Some keyboards have had slight modifications made in order to ensure
that they still build due to firmware size restrictions.
* Fixup LED_MATRIX compile.
* Parameterise ERROR_DISCONNECT_COUNT.