* disambiguate Bootmagic rules in keymaps
The files edited by this commit were added at a point in time where `BOOTMAGIC_ENABLE = yes` enabled full Bootmagic.
This commit edits the files to specify that full Bootmagic is intended.
* remove BOOTMAGIC_ENABLE=full setting
* unify commented BOOTMAGIC_ENABLE rules in keyboards
Explicitly sets `BOOTMAGIC_ENABLE = no` in keyboards where the rule was commented out.
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;#[ \t]*\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-zA-Z]\+\).*;\1 = no # Virtual DIP switch configuration;g' {} +
```
* remove commented Bootmagic rules from keymap/user level
Command:
```
find keyboards/ layouts/ users/ -type f -name 'rules.mk' -exec sed -i -e '/#.*\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*/d' {} +
```
* update keyboard BOOTMAGIC_ENABLE rule formatting
Sets the formatting of BOOTMAGIC_ENABLE rules to `BOOTMAGIC_ENABLE = [value]`, without the inline comments (which will be replaced later).
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
```
* update keyboards' BOOTMAGIC_ENABLE settings
Updates keyboard `rules.mk` files to use `BOOTMAGIC_ENABLE = lite` where `BOOTMAGIC_ENABLE = full` was being used.
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = \)full;\1lite;g' '{}' +
```
* update keymap/user BOOTMAGIC_ENABLE settings
Updates keymap/user `rules.mk` files to use `BOOTMAGIC_ENABLE = lite` where `BOOTMAGIC_ENABLE = full` was being used.
Commands:
```
find keyboards/ -type f -name 'rules.mk' -and -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE[ \t=]\+\)full;\1lite;g' '{}' +
find layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE[ \t=]\+\)full;\1lite;g' '{}' +
```
* remove and replace inline comments in keyboards and keymap/user files
Removes and replaces the inline comments, which have been updated to read `Enable Bootmagic Lite`.
Commands:
```
find keyboards/ -type f -name 'rules.mk' -and -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
find layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = lite\);\1 # Enable Bootmagic Lite;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = yes\);\1 # Enable Bootmagic Lite;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = no\);\1 # Enable Bootmagic Lite;g' '{}' +
```
* rename improperly named makefiles
Some files intended to be used as makefiles had improper names causing them to not be used as intended when building.
This commit corrects the filenames of the affected files.
* update renamed file with new rule formatting
* update QMK's template files
Updates QMK's `rules.mk` templates to use the new inline comment.
* update QMK Docs
- remove documentation of full Bootmagic
- update links to Bootmagic Lite doc
- add doc for Magic Keycodes
* rules.mk patch for coarse/ixora and coarse/vinta
* [Keyboard] Set reasonable defaults for Corne keyboard
* Add note about bootmagic
* Make bootmagic config super weak
* cleanup
* Apply suggestions from code review
* Update keyboards/crkbd/readme.md
Fix reddit link
Duplicate open parenthesis next to close parenthesis on NSSL
Add customisation instructions
Add lily58
Add gergo
Co-authored-by: Jonathan Dayton <jonathandayton23@gmail.com>
Clean up LAYOUT macro formatting
Add alternative vi-style navigation layout
Add kyria
Add minidox
Change order of keyboards
Add iris
Expand TOC
Re-order userspace subheadings
Add atreus
Add customisation section
Add split_3x5_3 and split_3x6_3 layouts
Add for_science
Fix wrong paths in keyboard config.h and keymap.c headings
Fix keyboard ordering
Fix blank lines around headings
Add compatibility with new org-mode version.
Remove keyboards/crkbd now covered by layouts/split_3x6_3
Add Halmak
Alphabetise alternative alpha arrangements
Move build options out of base layer alphas headings
Add list of keyboards supporting split_3x5_3 layout
Enable Auto Shift and Retro Shift
Add Retro Shift (Auto Shift for Tap Hold via Retro Tapping)
Change kyria thumb key mapping
Add planck_mit layout
Remove alternative bottom row support from ortho_4x12
Remove minidox
- Covered by split_3x5_3 layout
Add moonlander
Remove KC_ macros
Add 60_ansi layout
Add ortho_5x15 layout
Closesmanna-harbour/qmk_firmware#5
Co-authored-by: Rob <rob@debank.tv>
Fix typo (manna-harbour/qmk_firmware#7)
Author: sonnius <sonnius@users.noreply.github.com>
Add redox_w (manna-harbour/qmk_firmware#8)
Author: Brian Romanko <hello@bromanko.com>
Co-authored-by: Manna Harbour <51143715+manna-harbour@users.noreply.github.com>
Add AUTO_SHIFT_NO_SETUP to reduce firmware size
Update image paths
Add instructions to checkout development branch
Add kyria extended thumbs option, change default, add KLE
Change clipboard keys
- Change order to be mirror of windows bindings
- Change default to use CUA bindings for Cut, Copy, and Paste, and Fun Cluster
bindings for Undo and Redo
- Add alternative bindings
- Fun Cluster (original miryoku bindings)
- Mac
- Windows
- Change prefix for local macros from X_ to U_
Disable Retro Shift, enable Auto Shift for non-alphas
Revert "Add Retro Shift (Auto Shift for Tap Hold via Retro Tapping)"
Add Experimental Features section
Update miryoku image link
Update cover image link
Add dactyl_manuform/4x5
Add cutomisation examples
Add https to remote example
Fix dactyl_manuform/4x5 subset mapping
Add extended thumbs to ortho_4x12
Update Colemak Mod-DH naming
Closesmanna-harbour/qmk_firmware#13
Add dactyl_manuform/5x6
Resolvesmanna-harbour/qmk_firmware#14
Co-authored-by: Sebastian Morales <sebastian.moralesd@gmail.com>
Add note on FORCE_LAYOUT
- Needed to use EXTENDED_THUMBS on planck
Add parent directories to keyboard headings and re-order
Add keyboardio/atreus
Resolvesmanna-harbour/qmk_firmware#15
Add torn
Resolvesmanna-harbour/qmk_firmware#16
Author: Brian Romanko <hello@bromanko.com>
Co-authored-by: Manna Harbour <51143715+manna-harbour@users.noreply.github.com>
Change map to zip
- Adds support for python3, still compatible with python2.
Resolvesmanna-harbour/qmk_firmware#10Resolvesmanna-harbour/qmk_firmware#19
Co-authored-by: Ori <ori@oribarbut.com>
Add python-version
Add sofle
Add ergotravel
Add ortho_5x12
Add ortho_4x10
Add :main no header argument to C code blocks
resolvesmanna-harbour/qmk_firmware#11resolvesmanna-harbour/qmk_firmware#12
Co-authored-by: RubioJr9 <u0893472@utah.edu>
Add flipped layers and inverted-T nav alternative layouts
- Separate tap_table into alphas_table and thumbs_table
- Add mode argument to table-layout-half
- Remove layer_name
- Rename layers
- Add mods and clipboard to MBO and mirror
- Add MIRYOKU_LAYERS=FLIP
- Add MIRYOKU_NAV=INVERTEDT
Add layer diagrams
Update contact section
Update links for Bilateral Combinations and Retro Shift
Add description and no reverse angle option to 60_ansi layout
Update list of keyboards supporting community layouts
- and example build command lines
Change moonlander thumb keys
Update list of keyboards supporting split_3x5_3
Add license to tangled C source files
* Add Per Key functionality for AutoShift (#11536)
* LED Matrix: Reactive effect buffers & advanced indicators (#12588)
* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)
* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)
* LED Matrix: Split (#12633)
* [CI] Format code according to conventions (#12650)
* feat: infinite timeout for leader key (#6580)
* feat: implement leader_no_timeout logic
* docs(leader_key): infinite leader timeout docs
* Format code according to conventions (#12680)
* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)
* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)
Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).
* Update ADC docs to match the actually used resolution
ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly. Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).
* Fix pinToMux() for B12 and B13 on STM32F3xx
Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.
* Add support for all possible analog pins on STM32F1xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families). Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).
Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.
* Add support for all possible analog pins on STM32F4xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.
Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.
Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.
* Fix STM32F3xx ADC mux table in documentation
The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).
* Add STM32F1xx ADC pins to the documentation
* Add STM32F4xx ADC pins to the documentation
* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)
* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.
* Update flashing.md
* Update chconf.h
* Update config.h
* Update halconf.h
* Update mcuconf.h
* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)
* Add support for MCU = STM32F446 (#12619)
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
* Format code according to conventions (#12682)
* Format code according to conventions (#12687)
* Add STM32L433 and L443 support (#12063)
* initial L433 commit
* change to XC
* fix L433
* disable all peripherals
* update system and peripheral clocks
* 433 change
* use its own board files
* revert its own board files
* l433 specific change
* fix stm32l432xx define
* remove duplicate #define
* fix bootloader jump
* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h
* move to L443
* move to L443
* fix sdmmc in mcuconf.h
* include STM32L443
* add L443
* Include L443 in compatible microcontrollers
* Include L443 in compatible microcontrollers
* Update config bootloader jump description
* Update ChibiOS define reasoning
* Update quantum/mcu_selection.mk
* fix git conflict
* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)
* Fix bad PR merge for #6580. (#12721)
* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)
* [CI] Format code according to conventions (#12731)
* Fixing transport's led/rgb matrix suspend state logic (#12770)
* [CI] Format code according to conventions (#12772)
* Fix comment parsing (#12750)
* Added OLED fade out support (#12086)
* fix some references to bin/qmk that slipped in (#12832)
* Resolve a number of warnings in `qmk generate-api` (#12833)
* New command: qmk console (#12828)
* stash poc
* stash
* tidy up implementation
* Tidy up slightly for review
* Tidy up slightly for review
* Bodge environment to make tests pass
* Refactor away from asyncio due to windows issues
* Filter devices
* align vid/pid printing
* Add hidapi to the installers
* start preparing for multiple hid_listeners
* udev rules for hid_listen
* refactor to move closer to end state
* very basic implementation of the threaded model
* refactor how vid/pid/index are supplied and parsed
* windows improvements
* read the report directly when usage page isn't available
* add per-device colors, the choice to show names or numbers, and refactor
* add timestamps
* Add support for showing bootloaders
* tweak the color for bootloaders
* Align bootloader disconnect with connect color
* add support for showing all bootloaders
* fix the pyusb check
* tweaks
* fix exception
* hide a stack trace behind -v
* add --no-bootloaders option
* add documentation for qmk console
* Apply suggestions from code review
* pyformat
* clean up and flesh out KNOWN_BOOTLOADERS
* Remove pointless SERIAL_LINK_ENABLE rules (#12846)
* Make Swap Hands use PROGMEM (#12284)
This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.
* Fix another bin/qmk reference (#12856)
* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)
* Fixup build errors on `develop` branch. (#12723)
* LED Matrix: Effects! (#12651)
* Fix syntax error when compiling for ARM (#12866)
* Remove KEYMAP and LAYOUT_kc (#12160)
* alias KEYMAP to LAYOUT
* remove KEYMAP and LAYOUT_kc
* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)
* Rename `point_t` -> `led_point_t` (#12864)
* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)
* Add missing LED Matrix suspend code to suspend.c (#12878)
* LED Matrix: Documentation (#12685)
* Deprecate `send_unicode_hex_string()` (#12602)
* Fix spelling mistake regarding LED Matrix in split_common. (#12888)
* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)
* Use milc.subcommand.config instead of qmk.cli.config (#12915)
* Use milc.subcommand.config instead
* pyformat
* remove the config test
* Add function to allow repeated blinking of one layer (#12237)
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Fixup housekeeping from being invoked twice per loop. (#12933)
* matrix: wait for row signal to go HIGH for every row (#12945)
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* ensure we do not conflict with existing keymap aliases (#12976)
* Add support for up to 4 IS31FL3733 drivers (#12342)
* Convert Encoder callbacks to be boolean functions (#12805)
* [Keyboard] Fix Terrazzo build failure (#12977)
* Do not hard set config in CPTC files (#11864)
* [Keyboard] Corne - Remove legacy revision support (#12226)
* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)
* Add Full-duplex serial driver for ARM boards (#9842)
* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)
* Backlight: add defines for default level and breathing state (#12560)
* Add dire message about LUFA mass storage bootloader (#13014)
* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)
Was causing compiler errors on some systems.
* Fix keyboards/keymaps for boolean encoder callback changes (#12985)
* `backlight.c`: include `eeprom.h` (#13024)
* Add changelog for 2021-05-29 Breaking Changes merge (#12939)
* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version
* Add recent develop changes
* Sort recent develop changes
* Remove sections for ChibiOS changes per tzarc
No ChibiOS changes this round.
* Add and sort recent develop changes
* add notes about keyboard moves/deletions
* import changelog for PR 12172
Documents the change to BOOTMAGIC_ENABLE.
* update section headings
* re-sort changelog
* add additional note regarding Bootmagic changes
* remove changelog timestamp
* update dates in main Breaking Changes docs
* fix broken section anchors in previous changelogs
* add link to backlight/eeprom patch to changelog
* highlight some more changes
* link PRs from section headers
* Restore standard readme
* run: qmk cformat --core-only
This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.
* Redo Arm DAC implementation for additive, wavetable synthesis, sample playback
changes by Jack Humbert on an implementation for DAC audio on arm/chibios platforms
this commits bundles the changes from the arm-dac-work branch focused on audio/audio_arm.* into one commit (leaving out the test-keyboard)
f52faeb5d (origin/arm-dac-work) add sample and wavetable examples, parsers for both
-> only the changes on audio_arm_.*, the keyboard related parts are split off to a separate commit
bfe468ef1 start morphing wavetable
474d100b5 refined a bit
208bee10f play_notes working
3e6478b0b start in-place documentation of dac settings
3e1826a33 fixed blip (rounding error), other waves, added key selection (left/right)
73853d651 5 voices at 44.1khz
dfb401b95 limit voices to working number
9632b3379 configuration for the ez
6241f3f3b notes working in a new way
* Redo Arm DAC implementation for additive, wavetable synthesis, sample playback
changes by Jack Humbert on an implementation for DAC audio on arm/chibios platforms
this commit splits off the plank example keymap from commit
f52faeb5d (origin/arm-dac-work) add sample and wavetable examples, parsers for both
* refactoring: rename audio_ to reflect their supported hardware-platform and audio-generation method: avr vs arm, and pwm vs dac
* refactoring: deducplicate ISR code to update the pwm duty-cycle and period in the avr-pwm-implementation
pulls three copies of the same code into one function
which should improve readability and maintainability :-)
* refactoring: move common code of arm and avr implementation into a separate/new file
* refactoring: audio_avr_pwm, renaming defines to decouple them from actually used timers, registers and ISRs
* refactoring: audio_avr_pwm - replacing function defines with plain register defines
aligns better with other existing qmk code (and the new audio_arm_pwm) doing similar pwm thing
* add audio-arm-pwm
since not all STM32 have a DAC onboard (STM32F2xx and STM32F3xx), pwm-audio is an alternative (STM32F1xx)
this code works on a "BluePill" clone, with an STM32F103C8B
* clang-format changes on quantum/audio/* only
* audio_arm_dac: stopping the notes caused screeching when using the DAC audio paths
* audio_arm_pwm: use pushpull on the pin; so that a piezzo can be hooked up direclty without additional components (opendrain would require an external pullup)
* refactoring: remove unused file from/for atmel-avr chips
* refactoring: remove unused (avr) wavetable file
* audio_arm_dac: adapt dac_end callback to changed chibios DAC api
the previous chibios (17.6.0) passed along a pointer into the buffer plus a sample_count (which are/already where included in the DACDrivre object) - the current chibios (19.1.0) only passes the driver object.
this patch ports more or less exactly what the previous chibios ISR code did: either have the user-callback work the first or second half of the buffer (dacsample_t pointer, with half the DAC_BUFFER_SIZE samples) by adjusting the pointer and sample count
* audio-arm-dac: show a compile-warning on undefined audio-pins
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* audio_arm_dac: switch from exemplary wavetable generation to sine only
sine+triangle+squrare is exemplary, and not realy fit for "production" use
'stairs' are usefull for debugging (hardware, with an oscilloscope)
* audio_arm_dac: enable output buffers in the STM32
to drive external loads without any additional ciruitry - external opamps and such
* audio: prevent out-of-bounds array access
* audio_arm_dac: add output-frequency correcting factor
* audio_arm_pwm: get both the alternate-function and pm-callback variants back into working condition
and do some code-cleanup, refine documentation, ...
* audio_arm_pwm: increase pwm frequency for "higher fidelity"
on the previous .frequency=100000 higher frequency musical notes came out wrong
(frequency measured on a Tektronix TDS2014B)
note | freq | arm-pwm
C2 | 65.4 | 65.491
C5 | 523.25 | 523.93
C6 | 1046.5 | 1053.38
C7 | 2093 | 2129
C8 | 4186 | 4350.91
with .frequency = 500000
C8 | 4186 | 4204.6
* audio refactoring: remove unused variables
* audio_arm_dac: calibrate note tempo: with a tempo of 60beats-per-second a whole-note should last for exactly one second
* audio: allow feature selection in rules.mk
so the user can switch the audio driver between DAC and PWM on STM32 boards which support both (STM32F2 and up)
or select the "pin alternate" pwm mode, for example on STM32F103
* audio-refactoring: move codeblocks in audio.[ch] into more coherent groups
and add some inline documentation
* audio-refactoring: cleanup and streamline common code between audio_arm_[dac|pwm]
untangeling the relation between audio.c and the two drivers
and adding more documenting comments :-)
* audio_avr_pwm: getting it back into working condition, and cleanup+refactor
* audio-refactoring: documentation and typo fixes
Co-Authored-By: Nick Brassel <nick@tzarc.org>
* audio-refactoring: cleanup defines, inludes and remove debug-prints
* audio_chibios_dac: define&use a minimal sampling rate, based on the available tone-range
to ease up on the cpu-load, while still rendering the higher notes/tones sufficiently
also reenable the lower tones, since with the new implementation there is no evidence of them still beeing 'bugged'
* audio-refactoring: one common AUDIO_MAX_VOICES define for all audio-drivers
* audio-chibios-pwm: pwm-pin-allternate: make the the timer, timer-channel and alternate function user-#definable
* audio_chibios_dac: math.h has fmod for this
* Redo Arm DAC implementation for additive, wavetable synthesis, sample playback
update Jack Humberts dac-example keymaps for the slight changes in the audio-dac interface
* audio-refactoring: use a common AUDIO_PIN configuration switch instead of defines
have the user select a pin by configuration in rules.mk instead of a define in config.h
has the advantage of beeing in a common form/pattern across all audio-driver implementations
* audio-refactoring: switch backlight_avr.c to the new AUDIO_PIN defines
* audio-common: have advance_note return a boolean if the note changed, to the next one in the melody beeing played
* audio-chibios-pwm: fix issue with ~130ms silence between note/frequency changes while playing a SONG
through trial,error and a scope/logic analyzer figured out Chibios-PWMDriver (at least in the current version) misbehaves if the initial period is set to zero (or one; two seems to work); when thats the case subsequent calls to 'pwmChhangePeriod' + pwmEnableChannel took ~135ms of silence, before the PWM continued with the new frequency...
* audio-refactoring: get 'play_note' working again
with a limited number of available voices (say AUDIO_VOICES_MAX=1) allow new frequencies to be played, by discarding the oldest one in the 'frequencies' queue
* audio: set the fallback driver to DAC for chibios and PWM for all others (==avr at the moment)
* audio-refactoring: moore documentation
and some cleanup
* audio-avr-pwm: no fallback on unset AUDIO_PIN
this seems to be the expected behaviour by some keyboards (looking at ckeys/handwire_101:default) which otherwise fail to build because the firmware-image ends up beeing too large for the atmega... so we fail silently instead to keep travis happy
* audio-refactoring: untangling terminology: voice->tone
the code actually was working on tones (combination of pitch/frequency, duration, timbre, intensity/volume) and not voices (characteristic sound of an instrument; think piano vs guitar, which can be played together, each having its own "track" = voice on a music sheet)
* audio-pwm: allow freq=0 aka a pause/rest in a SONG
continue processing, but do not enable pwm units, since freq=0 wouldn't produce any sound anyway (and lead to division by zero on that occasion)
* audio-refactoring: audio_advance_note -> audio_advance_state
since it does not only affect 'one note', but the internally kept state as a whole
* audio-refactoring: untangling terminology: polyphony
the feature om the "inherited" avr code has little to do with polyphony (see wikipedia), but is more a time-multiplexing feature, to work around hardware limitations - like only having one pwm channel, that could on its own only reproduce one voice/instrument at a time
* audio-chibios-dac: add zero-crossing feature
have tones only change/stop when the waveform approaches zero - to avoid audible clicks
note that this also requires the samples to start at zero, since the internally kept index into the samples is reset to zero too
* audio-refactoring: feature: time-multiplexing of tones on a single output channel
this feature was in the original avr-pwm implementation misnomed as "polyphony"
with polyphony_rate and so on; did the same thing though: time-multiplexing multiple active notes so that a single output channel could reproduce more than one note at a time (which is not the same as a polyphony - see wikipedia :-) )
* audio-avr-pwm: get music-mode working (again) on AVRs
with both pwm channels, or either one of the two :-)
play_notes worked already - but music_mode uses play_note
* audio-refactoring: split define MAX_SIMULTANEOUS_TONES -> TONE_STACKSIZE
since the two cases are independant from one another, the hardware might impose limitations on the number of simultaneously reproducable tones, but the audio state should be able to track an unrelated number of notes recently started by play_note
* audio-arm-dac: per define selectable sample-luts
plus generation script in ./util
* audio-refactoring: heh, avr has a MIN...
* audio-refactoring: add basic dac audio-driver based on the current/master implementation
whereas current=d96380e65496912e0f68e6531565f4b45efd1623
which is the state of things before this whole audio-refactoring branch
boiled down to interface with the refactored audio system = removing all
redundant state-managing and frequency calculation
* audio-refactoring: rename audio-drivers to driver_$PLATFORM_$DRIVER
* audio-arm-pwm: split the software/hardware implementations into separate files
which saves us partially from a 'define hell', with the tradeoff that now two somewhat similar chibios_pwm implementations have to be maintained
* audio-refactoring: update documentation
* audio-arm-dac: apply AUDIO_PIN defines to driver_chibios_dac_basic
* audio-arm-dac: dac_additive: stop the hardware when the last sample completed
the audio system calls for a driver_stop, which is delayed until the current sample conversion finishes
* audio-refactoring: make function-namespace consistent
- all (public) audio functions start with audio_
- also refactoring play*_notes/tones to play*_melody, to visually distance it a bit from play*_tone/_note
* audio-refactoring: consistent define namespace: DAC_ -> AUDIO_DAC_
* audio-arm-dac: update (inline) documentation regarding MAX for sample values
* audio-chibios-dac: remove zero-crossing feature
didn't quite work as intended anyway, and stopping the hardware on close-to-zero seems to be enought anyway
* audio-arm-dac: dac_basic: respect the configured sample-rate
* audio-arm-pwm: have 'note_timbre' influence the pwm-duty cycle
like it already does in the avr implementation
* audio-refactoring: get VIBRATO working (again)
with all drivers (verified with chibios_[dac|pwm])
* audio-arm-dac: zero-crossing feature (Mk II)
wait for the generated waveform to approach 'zero' before either turning off the output+timer or switching to the current set of active_tones
* audio-refactoring: re-add note-resting -> introduce short_rest inbetween
- introduce a short pause/rest between two notes of the same frequency, to separate them audibly
- also updating the refactoring comments
* audio-refactoring: cleanup refactoring remnants
remove the former avr-isr code block - since all its features are now refactored into the different parts of the current system
also updates the TODOS
* audio-refactoring: reserve negative numbers as unitialized frequencies
to allow the valid tone/frequency f=0Hz == rest/pause
* audio-refactoring: FIX: first note of melody was missing
the first note was missing because 'goto_next_note'=false overrode a state_change=true of the initial play_tone
and some code-indentations/cleanup of related parts
* audio-arm-dac: fix hardware init-click
due to wron .init= value
* audio-refactoring: new conveniance function: audio_play_click
which can be used to further refactor/remove fauxclicky (avr only) and/or the 'clicky' features
* audio-refactoring: clang-format on quantum/audio/*
* audio-avr-pwm: consecutive notes of the same frequency get a pause inserted inbetween by audio.c
* audio-refactoring: use milliseconds instead of seconds for 'click' parameters
clicks are supposed to be short, seconds make little sense
* audio-refactoring: use timer ticks instead of counters
local counters were used in the original (avr)ISR to advance an index into the lookup tables (for vibrato), and something similar was used for the tone-multiplexing feature
decoupling these from the (possibly irregular) calls to advance_state made sesne, since those counters/lookups need to be in relation to a wall-time anyway
* audio-refactoring: voices.c: drop 'envelope_index' counter in favour of timer ticks
* audio-refactoring: move vibrato and timbre related parts from audio.c to voices.c
also drops the now (globally) unused AUDIO_VIBRATO/AUDIO_ENABLE_VIBRATO defines
* audio.c: use system-ticks instead of counters the drivers have to take care of for the internal state posision
since there already is a system-tick with ms resolution, keeping count separatly with each driver implementation makes little sense; especially since they had to take special care to call audio_advance_state with the correct step/end parameters for the audio state to advance regularly and with the correct pace
* audio.c: stop notes after new ones have been started
avoids brief states of with no notes playing that would otherwise stop the hardware and might lead to clicks
* audio.c: bugfix: actually play a pause
instead of just idling/stopping which lead the pwm drivers to stop entirely...
* audio-arm-pwm: pwm-software: add inverted output
new define AUDIO_PIN_ALT_AS_NEGATIVE will generate an inverted signal on the alternate pin, which boosts the volume if a piezo is connected to both AUDIO_PIN and AUDIO_PIN_ALT
* audio-arm-dac: basic: handle piezo configured&wired to both audio pins
* audio-refactoring: docs: update for AUDIO_PIN_ALT_AS_NEGATIVE and piezo wiring
* audio.c: bugfix: use timer_elapsed32 instad of keeping timestamps
avoids running into issues when the uint32 of the timer overflows
* audio-refactoring: add 'pragma once' and remove deprecated NOTE_REST
* audio_arm_dac: basic: add missing bracket
* audio.c: fix delta calculation
was in the wrong place, needs to use the 'last_timestamp' before it was reset
* audio-refactoring: buildfix: wrong legacy macro for set_timbre
* audio.c: 16bit timerstamps suffice
* audio-refactoring: separate includes for AVR and chibios
* audio-refactoring: timbre: use uint8 instead of float
* audio-refactoring: duration: use uint16 for internal per-tone/note state
* audio-refactoring: tonemultiplexing: use uint16 instead of float
* audio-arm-dac: additive: set second pin output-low
used when a piezo is connected to AUDIO_PIN and AUDIO_PIN_ALT, with PIN_ALT_AS_NEGATIVE
* audio-refactoring: move AUDIO_PIN selection from rules.mk to config.h
to be consistent with how other features are handled in QMK
* audio-refactoring: buildfix: wrong legacy macro for set_tempo
* audio-arm-dac: additive: set second pin output-low -- FIXUP
* audio.c: do duration<>ms conversion in uint instead of float
on AVR, to save a couple of bytes in the firmware size
* audio-refactoring: cleanup eeprom defines/usage
for ARM, avr is handled automagically through the avr libc and common_features.mk
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* audio.h: throw an error if OFF is larger than MAX
* audio-arm-dac: basic: actually stop the dac-conversion on a audio_driver_stop
to put the output pin in a known state == AUDIO_DAC_OFF_VALUE, instead of just leaving them where the last conversion was... with AUDIO_PIN_ALT_AS_NEGATIVE this meant one output was left HIGH while the other was left LOW
one CAVEAT: due to this change the opposing squarewave when using both A4 and A5 with AUDIO_PIN_ALT_AS_NEGATIVE
show extra pulses at the beginning/end on one of the outputs, the two waveforms are in sync otherwise.
the extra pusles probably matter little, since this is no high-fidelity sound generation :P
* audio-arm-dac: additive: move zero-crossing code out of dac_value_generate
which is/should be user-overridable == simple, and doing one thing: providing sample values
state-transitions necessary for the zero crossing are better handled in the surrounding loop in the dac_end callback
* audio-arm-dac: dac-additive: zero-crossing: ramping up or down
after a start trigger ramp up: generate values until zero=OFF_VALUE is reached, then continue normally
same in reverse for strop trigger: output values until zero is reached/crossed, then keep OFF_VALUE on the output
* audio-arm-dac: dac-additive: BUGFIX: return OFF_VALUE when a pause is playing
fixes a bug during SONG playback, which suddenly stopped when it encoutnered a pause
* audio-arm-dac: set a sensible default for AUDIO_DAC_VALUE_OFF
1/2 MAX was probably exemplary, can't think of a setup where that would make sense :-P
* audio-arm-dac: update synth_sample/_wavetable for new pin-defines
* audio-arm-dac: default for AUDIO_DAC_VALUE_OFF
turned out that zero or max are bad default choices:
when multiple tones are played (>>5) and released at the same time (!), due to the complex waveform never reaching 'zero' the output can take quite a while to reach zero, and hence the zero-crossing code only "releases" the output waaay to late
* audio-arm-dac: additive: use DAC for negative pin
instead of PAL, which only allows the pin to be configured as output; LOW or HIGH
* audio-arm-dac: more compile-time configuration checks
* audio-refactoring: typo fixed
* audio-refactoring: clang-format on quantum/audio/*
* audio-avr-pwm: add defines for B-pin as primary/only speaker
also updates documentation.
* audio-refactoring: update documentation with proton-c config.h example
* audio-refactoring: move glissando (TODO) to voices.c
refactored/saved from the original glissando implementation in then upstream-master:audio_avr.c
still needs some work though, as it is now the calculation *should* work, but the start-frequency needs to be tracked somewhere/somehow; not only during a SONG playback but also with user input?
* audio-refactoring: cleanup: one round of aspell -c
* audio-avr-pwm: back to AUDIO_PIN
since config_common.h expands them to plain integers, the AUDIO_PIN define can directly be compared to e.g. B5
so there is no need to deal with separate defines like AUDIO_PIN_B5
* audio-refactoring: add technical documentation audio_driver.md
which moves some in-code documentation there
* audio-arm-dac: move AUDIO_PIN checks into c-code
instead of doing everything with the preprocessor, since A4/A5 do not expand to simple integers, preprocessor int-comparison is not possible. but necessary to get a consistent configuration scheme going throughout the audio-code... solution: let c-code handle the different AUDIO_PIN configurations instead (and leave code/size optimizations to the compiler)
* audio-arm-dac: compile-fix: set AUDIO_PIN if unset
workaround to get the build going again, and be backwarts compatible to arm-keyboards which not yet set the AUDIO_PIN define. until the define is enforced through an '#error"
* audio-refactoring: document tone-multiplexing feature
* audio-refactoring: Apply suggestions from documentation review
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* audio-refactoring: Update docs/audio_driver.md
* audio-refactoring: docs: fix markdown newlines
Terminating a line in Markdown with <space>-<space>-<linebreak> creates an HTML single-line break (<br>).
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* audio-arm-dac: additive: fix AUDIO_PIN_ALT handling
* audio-arm-pwm: align define naming with other drivers
Co-authored-by: Joel Challis <git@zvecr.com>
* audio-refactoring: set detault tempo to 120
and add documentation for the override
* audio-refactoring: update backlight define checks to new AUDIO_PIN names
* audio-refactoring: reworking PWM related defines
to be more consistent with other QMK code
Co-authored-by: Joel Challis <git@zvecr.com>
* audio-arm: have the state-update-timer user configurable
defaulting to GPTD6 or GPTD8 for stm32f2+ (=proton-c)
stm32f1 might need to set this to GPTD4, since 6 and 8 are not available
* audio-refactoring: PLAY_NOTE_ARRAY was already removed in master
* Add prototype for startup
* Update chibiOS dac basic to disable pins on stop
* Add defaults for Proton C
* avoid hanging audio if note is completely missed
* Don't redefine pins if they're already defined
* Define A4 and A5 for CTPC support
* Add license headers to keymap files
* Remove figlet? comments
* Add DAC config to audio driver docs
* Apply suggestions from code review
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* Add license header to py files
* correct license header
* Add JohSchneider's name to modified files
AKA credit where credit's due
* Set executable permission and change interpeter
* Add 'wave' to pip requirements
* Improve documentation
* Add some settings I missed
* Strip AUDIO_DRIVER to parse the name correctly
* fix depreciated
* Update util/audio_generate_dac_lut.py
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* Fix type in clueboard config
* Apply suggestions from tzarc
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Johannes <you@example.com>
Co-authored-by: JohSchneider <JohSchneider@googlemail.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joshua Diamond <josh@windowoffire.com>
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* Initial attempt at allowing keyboards to indicate what features they do not support
* try to use a for loop instead
* Update disable_features.mk
Co-authored-by: Drashna Jaelre <drashna@live.com>
* add a few more features
* remove my test fixture
* disable things that make all:all suggested"
Co-authored-by: Zach White <skullydazed@users.noreply.github.com>
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Initial commit for my Corne keyboard layout.
* Updates to Corne, etc.
Finished working on primary layout for Corne keyboard.
Cleaned up some comments for my 4x12 Ortho layout.
* Changes for crkbd layout
* Fixed the config.h to reflect using ee_hands
* Added RGB configs to crkbd/corne layout
Co-authored-by: Ian Sterling <503326@MC02YT9K9LVCF.tld>
* Branch point for 2020 November 28 Breaking Change
* Remove matrix_col_t to allow MATRIX_ROWS > 32 (#10183)
* Add support for soft serial to ATmega32U2 (#10204)
* Change MIDI velocity implementation to allow direct control of velocity value (#9940)
* Add ability to build a subset of all keyboards based on platform.
* Actually use eeprom_driver_init().
* Make bootloader_jump weak for ChibiOS. (#10417)
* Joystick 16-bit support (#10439)
* Per-encoder resolutions (#10259)
* Share button state from mousekey to pointing_device (#10179)
* Add hotfix for chibios keyboards not wake (#10088)
* Add advanced/efficient RGB Matrix Indicators (#8564)
* Naming change.
* Support for STM32 GPIOF,G,H,I,J,K (#10206)
* Add milc as a dependency and remove the installed milc (#10563)
* ChibiOS upgrade: early init conversions (#10214)
* ChibiOS upgrade: configuration file migrator (#9952)
* Haptic and solenoid cleanup (#9700)
* XD75 cleanup (#10524)
* OLED display update interval support (#10388)
* Add definition based on currently-selected serial driver. (#10716)
* New feature: Retro Tapping per key (#10622)
* Allow for modification of output RGB values when using rgblight/rgb_matrix. (#10638)
* Add housekeeping task callbacks so that keyboards/keymaps are capable of executing code for each main loop iteration. (#10530)
* Rescale both ChibiOS and AVR backlighting.
* Reduce Helix keyboard build variation (#8669)
* Minor change to behavior allowing display updates to continue between task ticks (#10750)
* Some GPIO manipulations in matrix.c change to atomic. (#10491)
* qmk cformat (#10767)
* [Keyboard] Update the Speedo firmware for v3.0 (#10657)
* Maartenwut/Maarten namechange to evyd13/Evy (#10274)
* [quantum] combine repeated lines of code (#10837)
* Add step sequencer feature (#9703)
* aeboards/ext65 refactor (#10820)
* Refactor xelus/dawn60 for Rev2 later (#10584)
* add DEBUG_MATRIX_SCAN_RATE_ENABLE to common_features.mk (#10824)
* [Core] Added `add_oneshot_mods` & `del_oneshot_mods` (#10549)
* update chibios os usb for the otg driver (#8893)
* Remove HD44780 References, Part 4 (#10735)
* [Keyboard] Add Valor FRL TKL (+refactor) (#10512)
* Fix cursor position bug in oled_write_raw functions (#10800)
* Fixup version.h writing when using SKIP_VERSION=yes (#10972)
* Allow for certain code in the codebase assuming length of string. (#10974)
* Add AT90USB support for serial.c (#10706)
* Auto shift: support repeats and early registration (#9826)
* Rename ledmatrix.h to match .c file (#7949)
* Split RGB_MATRIX_ENABLE into _ENABLE and _DRIVER (#10231)
* Split LED_MATRIX_ENABLE into _ENABLE and _DRIVER (#10840)
* Merge point for 2020 Nov 28 Breaking Change
* update keymap for unikorn
* add new map
* update keymap
* update keymap
* update map
* update the current keymap
* update keymap so it accounts for mouse keys as well
* add extra control and shift, for when we need to use the other keys
* get me square and curly braces
* remove unused macros
* update these changes so far
* update ilpse keymap
* rmove a layer and simplify my layers a bit
* I think there's a working keymap now for the corne. let's leave this here.
* I thought maybe that helped? but who knows
* save changes made so far
* update madhatter keymap to match what I want
* switch to use lcmd for main alt
* update my curiosity keymap
* make curiosity via enabled
* add via keymap
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Update keyboards/primekb/prime_e/keymaps/madhatter/keymap.c
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Drashna Jaelre <drashna@live.com>
* stick to enum
* add bootmagic stuff and update keymap
* switch to bootmagic lite
* fix typo
* cleanup for writing to LED
* consistency
* fix led pins
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* fix build issue
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update keyboards/crkbd/keymaps/madhatter/keymap.c
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Khader Syed <khader.syed@aicure.com>
Co-authored-by: Drashna Jaelre <drashna@live.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Refactor the crkbd/via keymap and fix OLED bugs
* Revert "Refactor the crkbd/via keymap and fix OLED bugs"
This reverts commit dc9db029fc.
* Fix OLED display bugs
* Remove unused functions
* Remove uncessary the key logger
* Add new lines at end of file
* Remove unnecesary extern for is_master
* Remove extern is_master from rev1.h
* Remove ssd1306 from common dir because its the legacy lib
* Update default keymap based the via keymap
* Remove foostan keymap because it will be legacy
* Revert Remove unnecesary extern for is_master
* Remove unnecessary backslashes.
Add Eco keymap, factor Crkbd keymap to community layout, other minor tweaks
* Remove outdated Crkbd Ctrl key positioning info
* Add Left Alt key to Lily58 keymap
* Lily58 no longer overrides default TAPPING_TERM
* Refactor Crkbd keymap to use new community layout
* Fix underglow animations for Crkbd w/ Split Common
* Add initial Eco keymap
* Update outdated reference to Crkbd layout
* Add keymap links to userspace readme
* Add copyright notices to files changed in this PR
* Add Launchpad keymap
Note: RGB and Audio won't work when using B pins for audio
* Add support for rgb matrix on launchpad
* Update config for launchpag
* Disable wait on layer change
* Update config for ErgoDox EZ
* Fixup rgb light userspace code
* Move Corne layout to community layouts folder
* Update config for corne to support community layouts
* Add license header to files
* Minor cleanup of userspace config
* Update Pimironi Trackball code
* Increase debounce time on ergodox
* Fix keymap handling
* Enable wait for USB for moonlander
* Update/add license headers
* fix review issues
* [Keyboard] Convert Corne Keyboard to Split Common
* Add VIA Support
* Makes sure that ol(e)d and new OLED implementation can't coexist
* Add licensing header to files
* Add changes based on feedback from foostan
* Fixes
* Better handle LTO_ENABLE
Especially when calling from command line
* Replace LINK_TIME_OPTIMIZATION_ENABLE with LTO_ENABLE
* Remove long for LTO from show_options.mk
* Add split_3x5_3 support to Minidox
* Add split_3x5_3 support to Miniaxe
* Add LAYOUT_mini to Centromere
This layout macro removes the need or KC_NO keycodes in the keymap.
* Add split_3x5_3 support to Centromere
* Add split_3x5_3 support to suihankey split
* Add LAYOUT_mini to centromere/info.json
* Add LAYOUT_mini to crkbd
* Add split_3x5_3 support to crkbd
* Change mini layout names
* Rename main layouts for split_3x6_3 keyboards
* Use split_3x5_3 macro for remaining keyboards
* Update relevant info.json files
* Fix suihankey/split/alpha macro
* Add layout aliases for suihankey
* Re-enable mouse keys to fix Chrome OS media keys
I'm not sure if there's a bug in Chrome OS, QMK, or both, but
EXTRAKEY_ENABLE isn't sufficient for media keys to work on Chrome OS.
Instead, MOUSEKEY_ENABLE is also required.
* Remove unnecessary SPLIT_USB_DETECT for Lily58
I've since swapped my Lily58 back to Elite-C v2 controllers with working
VBUS detection.
* Move Crkbd Esc and Ctrl keys; add some shortcuts
* Move MC_ALTT to userspace for cross-board support
* Sync Lily58 keymap with Crkbd
* Fix typos
OLED Display fixes
Add support for RGBLIGHT Layers
Add gaming layer to corn and kyria
RGBLight Startup Animation fixes and improvements (uses matrix_scan now!)
Pimoroni Trackball support added (IT'S RGB!!!)
Fix issues due to code changes
* Add custom corne keymap
* Clean up rules.mk
* Clean up base layer on keymap.c
* Clean up lower layer on keymap.c
* Clean up raise layer on keymap.c
* Clean up adjust layer in keymap.c
* Branch point for 2020 May 30 Breaking Change
* Migrate `ACTION_LAYER_TOGGLE` to `TG()` (#8954)
* Migrate `ACTION_MODS_ONESHOT` to `OSM()` (#8957)
* Migrate `ACTION_DEFAULT_LAYER_SET` to `DF()` (#8958)
* Migrate `ACTION_LAYER_MODS` to `LM()` (#8959)
* Migrate `ACTION_MODS_TAP_KEY` to `MT()` (#8968)
* Convert V-USB usbdrv to a submodule (#8321)
* Unify Tap Hold functions and documentation (#8348)
* Changing board names to prevent confusion (#8412)
* Move the Keyboardio Model01 to a keyboardio/ subdir (#8499)
* Move spaceman keyboards (#8830)
* Migrate miscellaneous `fn_actions` entries (#8977)
* Migrate `ACTION_MODS_KEY` to chained mod keycodes (#8979)
* Organizing my keyboards (plaid, tartan, ergoinu) (#8537)
* Refactor Lily58 to use split_common (#6260)
* Refactor zinc to use split_common (#7114)
* Add a message if bin/qmk doesn't work (#9000)
* Fix conflicting types for 'tfp_printf' (#8269)
* Fixed RGB_DISABLE_AFTER_TIMEOUT to be seconds based & small internals cleanup (#6480)
* Refactor and updates to TKC1800 code (#8472)
* Switch to qmk forks for everything (#9019)
* audio refactor: replace deprecated PLAY_NOTE_ARRAY (#8484)
* Audio enable corrections (2/3) (#8903)
* Split HHKB to ANSI and JP layouts and Add VIA support for each (#8582)
* Audio enable corrections (Part 4) (#8974)
* Fix typo from PR7114 (#9171)
* Augment future branch Changelogs (#8978)
* Revert "Branch point for 2020 May 30 Breaking Change"
* Fix crkbd slave matrix print to require debug_matrix
* Remove redundant include
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Move menu key on ergo boards to match staggered
* Unify 60_tsangan_hhkb and 60_ansi_split_bs_rshift
* Sync KBD67, Quefrency with community layouts
* Update ergo KLE images
* Update community layout KLE images
* Update KLE images/descriptions for remaining keebs
* Remove more mouse keys settings missed in #8836
* Turn off more unwanted make options
* clang-format my userspace
* Reword ergo layout docs so Crkbd is canonical
* Add a basic readme to my userspace
* Tweak Crkbd readme wording and fix typos
* Enable SPLIT_USB_DETECT for Lily58 w/ Elite-C bug
* Enable External EEPROM on Planck Rev6
* Update KC_MAKE macro to use qmk cli util
* Disable additional gradients for rgb matrix
* Update analog code for newer methods
* Update ergodox layout
* Disable Grave Escape
* Cleanup OLED code a bit
* Remove old unicode code
* Seperate RGB Matrix code from RGB Light code in userspace
* Massive overhaul an generalization of personal OLED code
Now lets hope I NEVER get a keyboard using a 128x32 in a normal orientation.
* Super tiny cleanup
* Enable Diablo layer on kyria
* clang format pass
* Additional OLED cleanup
* [keymap] ninjonas keymap updates
* [refactor(kyria)] updating keymap for numpad layer to be transparent rather than ignores
* [keymap(lily58)] added numpad layer
* [keymap(crkbd)] added numpad layer activated through tapdance
* [fix(8170)] fixing code review changes requested by noroadsleft
* [fix(8170)] updating comments and .md files to use 'Cmd' instead of and ⌘
* [keymap(kyria)] moved OLED & encoder implementation to separate classes
* [feat] created logic to cycle through hue wheel when starting keyboard
* [feat] created logic to cycle through hue wheel and return to user's default color
* [refactor] updating OLED layout for crkbd & lily58
* [refactor] updating OLED layout for crkbd & lily58
* [fix(8070)] updating encoder.c logic based off drashna's code review
* [refactor(8070)] added key to send + Shift + M
* Removed reference to firmware size in 0-9,a-f board-level and default keymap 'rules.mk' files
* Correct some 'rules.mk' in boards buried under vendor folders
* PR8027 patch
Co-authored-by: GeorgeKoenig <35542036+GeorgeKoenig@users.noreply.github.com>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* Added KidBrazil custom keymap for CRKBD
-Custom Font
-Custom OLED output
* Added missing readme
* Oled Timeout Update for KidBrazil Keymap (#1)
* Setup Oled timeout based on simple timer
* Cleaned up comments and added timeout for LEDs
* Fixed some small errors
* Updated oled timout with matrix scan
* Updated oled timout with matrix scan
* Update withou eeprom
* Update timer code
* Use process user instead of keymap
* Added ifdef to protect oledtimer
* Updated with half timeout state for logo
* Removed middle tier timer
* Final cleanup of unused files
* Updated code as per suggestions & requests
* Second round of revisions
* Updated keymap to better handle LED timeout
- Added boolean to hold LED state
- Added init function to set rgb to known state
- Modified RGB_TOG to work with noeeprom commands
* Finished adding the timeout for OLED and testing on CRKBD
* Updated documentation
* fixed the timeout logic so it works as intended
* Added initial limits to color settings
* Added layer reset as part of the iddle timeout process
* Split Keymap into more manageable files
* Finalizing RGB Layer status on CRKBD
- Refactored OLED timeout to deal only with oled
- If user remains iddle on game layer for too long it will switch to
default
- LED / OLED iddle working
- Minor changes to _SYM layer
- Removed some rgb controls from keyboard due to layer dependent RGB
colors
* Update keyboards/crkbd/keymaps/kidbrazil/keymap.c
Used suggestion from Drashna to replace EEPROM_RESET with shorter version.
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Update keyboards/crkbd/keymaps/kidbrazil/keymap.c
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Implemented drashna's comment
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Added KidBrazil custom keymap for CRKBD
-Custom Font
-Custom OLED output
* Added missing readme
* Oled Timeout Update for KidBrazil Keymap (#1)
* Setup Oled timeout based on simple timer
* Cleaned up comments and added timeout for LEDs
* Fixed some small errors
* Updated oled timout with matrix scan
* Updated oled timout with matrix scan
* Update withou eeprom
* Update timer code
* Use process user instead of keymap
* Added ifdef to protect oledtimer
* Updated with half timeout state for logo
* Removed middle tier timer
* Final cleanup of unused files
* Updated code as per suggestions & requests
* Second round of revisions
* Updated keymap to better handle LED timeout
- Added boolean to hold LED state
- Added init function to set rgb to known state
- Modified RGB_TOG to work with noeeprom commands
* Finished adding the timeout for OLED and testing on CRKBD
* Updated documentation
* fixed the timeout logic so it works as intended
* Update keyboards/crkbd/keymaps/kidbrazil/README.md
* Left-right gradient.
* Update the comment to match the new functionality.
* CPP does integer division so this round is not necessary.
* The x-range is actually 224, update comment and use bit-shifting again.
* Update docs with gradient left-right effect and associated "DISABLE" option.
* Added my UT47.2 Swedish layout with tap dance function.
* Move tap dance over to user space
* Removed config_common from config file
* Changes to workspace with new support for code16. Tested ok
* Swedish support
* Added code16 version of tapdance to userprofile.
* Created 4th layer and updated readme file. Removed ascii rep of layout.
* Tabdance updates
* Removed duplicated RGB keys.
* Added hvp minivan config
* Fixed tapdance key maps
* Added Planck 1 space base hvp layout
* Start of hvp xd75 layout. Way to many keys
* Added working config ink test for atreus62
* fixed smaller layout changes
* Updated tap dance with option 5
* Added better thump keys
* Created lets split layout
* Removed not used modes
* Updated to correct url
* Readme file
* Atreus62 readme
* Cleanup of keymap file
* Added tap dance
* Fixed missed adjustment
* Added hvp planck setup
* Update ascii
* will this work better?
* removed ascii
* Planck 1 space setup
* Fixed ascii local
* Added Corne setup
* Changes for lets split
* Atreus62 config
* Added Lily58
* Setup corne
* Setup planck
* Updated lets split
* UT47 setup
* Setup a The Vanboard.
* Alt Ctrl
* #define D_NAVI MT(MOD_LCTL | MOD_LSFT, KC_D)
* Fix D_NAVI & plank midi
* Fixed PR comments
* Added pragma
* Moved def to user space
* Removed not used endif
* Added def to users space
* Added rules to van
* Removed not used part of config
* Removed not used layout
* Removed not needed comments
* Remove not needed keymap_config_t
* Removed broken ascii from readme files and removed not needed rules
* Added spaces to readme file
* Removed xd75 from branch
* Added KidBrazil custom keymap for CRKBD
-Custom Font
-Custom OLED output
* Added missing readme
* Oled Timeout Update for KidBrazil Keymap (#1)
* Setup Oled timeout based on simple timer
* Cleaned up comments and added timeout for LEDs
* Fixed some small errors
* Updated oled timout with matrix scan
* Updated oled timout with matrix scan
* Update withou eeprom
* Update timer code
* Use process user instead of keymap
* Added ifdef to protect oledtimer
* Updated with half timeout state for logo
* Removed middle tier timer
* Final cleanup of unused files
* Updated code as per suggestions & requests
* Second round of revisions
* Display logo for caps lock indication on crkbd using old OLED driver
* Add emacs read-only mode file variable to generated files
* use LTO_ENABLE instead of EXTRAFLAGS
This enables the same option, and disables action_macros, and action_functions, both of which seem to break when LTO is enabled. And this is a lot simpler to use.
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Remove keymap_config extern from default keymaps
* Revert unicode
Apparently VSCode does not like unicode, I didn't actually edit these lines, so it must have been automatic... :(
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Add Kyria Keymap
* Enable all RGBLIGHT Animations for ARM and high capacity AVR
* Reduce GNUC version for __has_include
* Cleanup Ortho 4x12 Community layout
* Update Collide 39 keymap
* Cleanup Keymaps
* Enable full 30 LEDs for Ergodox
* Change EEPROM Load timing
* Use RGB Matrix on Planck Rev6
* Use correct keymap swap
* Enable everything for ARM
* Only enable rgb sleep on avr until crash is fixed
* Add additional Kyria keymap config
* Overhaul Kyria OLED display
* Improve kyria keymap based on usage
* Minor tweaks to rules
* Update OLED code to truncate properly
* Fix RGB Light layer indication
* Switch all of biton32 to get_highest_layer function
* Fix OLED Keylogger display
* Run qmk cformat over all of my user files
* Slight tweak to kyria based on usage
* Move around LALT_T config
* Add comments about base wrappers to keymaps
* Another cformat pass
* Temp fix for VUSB boards and NKRO
* Convert tabs to spaces in rules.mk files
* Only enable RGBLight if it's enabled
* Add Encoder Flip setting
* Update OLED font file
* [Keyboard] Change Corne RGB Matrix split handling
This uses the "is_master" detection to set the led matrix, rather than a define at compile time.
This means that the same hex can be used for both halves, not just one or the other. The caveat is that this costs ~240 bytes to do.
However, I feel that this is a good trade-off, not just lazy.
* Update documentation for RGB Matrix on the Corne
* rebaselined the whole fork and added cool matrix animations
* Updated dfu bootloader rules, oleds working on test map
* Moving test branch into main
moving my _test branch files into the main since the repo is now in the dev branch, don't see any reason to keep separate folders.
* Update keymap.c
Adding DOT to number layer
* added LED sleeping
* working on getting matrix rgb to sleep upon usb suspend
uploading to github for qmk staff help
* Added master sleep on usb suspend
Unfortunately the sleep function does not work on the slave side so will probably revert this change later
* bringing hhkb config up to current with other tominabox1 configs
* Update config.h
since master side is the only one that sleeps, going to disable this for now.
* testing oled stuff
* Update rules.mk
* tinkering with oled still
* Finally fixed custom image with corne doug
* Adding keymap to dimple instead of screwing up the upstream references.
* Changed oled image to peepo ggers
* working on oled sleep
* Update keymap.c
* fixes oled wake/sleep issues
* Adding 🅱️ and BEPIS macros
* Update .gitignore
* Cleaning up and improving documentation
* Update keymap.c
* Adding my minivan keymap
* Fixed error on keymap
* fixed OLEDs not turning on and moved tapping term to the keymap file
* Changed tapping term from 200 to 250
* Revised Fkey layers, arrows, question mark locations
* Update keymap.c
* tweaked tapping term and types on CRKBD, revised layout on HHKB
* Update keymap.c
* general code cleanup, keymap displays
* Set up userspace for common keymap elements
* tapping term stuff for shift
* testing
* Fixed new tapdance for accessing number and fkey layers
* Update tominabox1.h
* stuff
* fixing function calls for userspace
* cleaning up crkbd config and moving stuff to userspace
* finally fixed oled lightup issues
* cleaning up a few maps and rules
* Removing permissive hold and returning spacefn to all boards.
* Settting up wrapper keymaps for Dimple, Minivan, and Corne
Wrappers
* small tweaks
* Update wrappers.h
* finishing wrappers on Minivan and Dimple
* Revised tapping term definition
Providing additional tapping term config for CRKBD only.
* Code cleanup and documentation
* Update readme.md
* Update readme.md
* Wrapers and continued code cleanup and documentation
* moved oled py scripts to user folder
* completed wrapper implementation of CRKBD
* added matrix startup mode - not working yet pending upstream changes
* removed unused code in tominabox1.c
* Fixing custom keycodes and tap dance indices
fixed custom keycodes and tap dance indices
Adding beginning of dimple RGB matrix definition
changed oled on corne to scrolling matrix thing
Added copy pasta
* Secondary layer tweaks
Swapping hands of numbers and symbols as well as tweaking tapping terms accordingly
* Update tominabox1.c
Continued refinement of tapping term to support better right hand symbol access.
* Fixes from pr 7014
Removed gitignore data from qmk master
Reverted changes to Drashna's crkbd keymap
Accepted changes to crkbd keymap
Added ignore to hhkb keymap - I think I need this because Teensy. Will revisit another time
* Removing hhkb keymap for rework
* Adding back hhkb keymap
Re-adding hhkb folder with ignores
* Reverting changes to Dimple default
totally did not intend to modify these
* Update keymap.c
Reverting changes to Drashna's corne map
* Accepting recommended changes
* Reduced tap hold caps delay
moved bootmagic enable to general usage
Revised tapping terms
Removed unused keycode defs
* bootmagic
* Update rules.mk
* Fixed permissions (support 7014) and bootmagic addition
Fixed permissions on Drashna's keymap and Dimple default keymap files.
Adding bootmagic to my crkbd config.
* Fixing permissions
* Change RGBLight pin for Planck Light
Move it to A0, so that the SPI? pins are available for BT hackery
* Add QMK DFU bootloader info
* Add Solenoid
* Disable annoying white LED on bottom
* Enable Solenoid on Corne
* Remove bounds for animations
* Increase debounce for Ergodox EZ to reduce repeat key issues
* Set swap hands key to be a hold-tap key
This way, it's not ANNOYING and doesn't swap the hands inteniontally
* Move MT Alt in Corne keymap
* Re-Add fine tuned control of secrets
* Squash mods to single row
* Add LRA settings to haptic feedback settings for Rev6
* Fix issue with non-Planck EZ keymaps
* Add 40 Percent Nano with Analog Joystick
* Add Collide39 keymap
* Fix OLED printing to be more flavorful
* Fix up Iris GamePad and come cleanup
* Expand OLED char map further
* Add modded characters to keylogger
* Here be dragons
Co-Authored-By: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
* Fix up rules for community layouts
* Some more OLED tweaks
* Add mod mask check function
* Change QMK DFU Audio pin to be correct
* Use manual STM config instead of CTPC for Collide 39
* Adding profile for Corne with tap dance Swedish support.
* Remove extern keymap_config_t keymap_config as no longer needed
* Changed to use tap_code over register_code
* Removed persistent_default_layer_set
* Moved macros to hvp user space ink tap dance code
* Removed not used functions
* Moved to an ifbased include statement
* Removed not needed characters
* using similar keymaps (with vim in mind) for planck and crkbd
* changed to rgb matrix and lower max brightness to prevent unresponsiveness
* readme and default rgb mode
* disable all the not wanted effects and activate the framebuffer ones
* changed effects
* changed custom keycodes to defines
* fixed comment
* [refactor] updating ninjonas layout blocks and standardized LOWER & ADJUST
* [feat] added new macro M_TERM to open MacOS terminal app
* [feat] introducing mod-tap functionality on keymap
* [fix] fixing oled turning on when it feels like it. thanks @drashna for helping
* [feat] updating OLED to rotate logo 180 degrees
* [feat] updating keymaps to reflect VSCode frequent habits
* [refactor] converting crkbd modifier keys to layer blocks
* [fix(#6903)] converting _delay_ms to wait_ms on launching terminal macro
* Add personal keymap
* Additional readme note
* Fix typo's in readme
* Additional layer key info in readme
* Update keyboards/crkbd/keymaps/rpbaptist/config.h
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Update keyboards/crkbd/keymaps/rpbaptist/rules.mk
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Update keyboards/crkbd/keymaps/rpbaptist/keymap.c
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Remove redundant config
* Remove disabling of NO_ACTION_MACRO and NO_ACTION_FUNCTION
* Remove layer keycode macros
* Use layer_state_t instead of uint32_t
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Use get_highest_layer instead of biton32
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* OLED_ROTATION_90 instead of 180
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Use get_highest_layer instead of biton32
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Use get_highest_layer instead of biton32
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Revert "OLED_ROTATION_90 instead of 180"
This reverts commit f14a4353ab.
It messed up the logo on slave
* Use IS_LED_ON function to check LED status
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Add a quefrency keymap
* New Alt-ernate layouts
* Enable Per Key Tapping Term to preserve sanity
* Use underglow and mod lights for status on Corne
* Update the drashna_ms keymap for quefrency
* Disable Audio since there isn't enough space
* Update KC_MAKE to ues :flash target
* Cleanup ergodox layout
* Enable i2c support for Iris
* Add keymap support for CG_SWAP
* Enable RGB Matrix Shutdown mode
* enable heatmap
* Update gitlab CI to install python3
* Remove game macros
These are no longer needed, and haven't been used in ages
* Cleanup planck layout
* Add RGB Matrix fun and RGB cleanup
* Add keycode and config for RGB Matrix idle animations
* Clean up rgb idle animation code
* Add rgb idle keycode to keymaps
* Fix issues with rgb matrix idle animation
* Fix some handling for idle animation
* Reduce idle animation timeout to 15s to be more reasonable
* fix up rgb stuff
* Fix isses with rgb functions not being called for matrix
* Use custom EEPROM Magic Number so testing is easier
* Extend Default Layer macro to support a lot more layers
* Fix bjohnson macropad
* Adjust KC_MAKE to process mods for more consistent behavior
* Fix up rgb stuff on corne
* Corne OLED Overhaul
* Fixes a number of issues with weirdness.
* Fixes issues with keylogger (should be more reliable now)
* Modulaize the OLED render sections
* Rewrite layer display code
* Update URL for Font Editor
Due to odd issues, I ended up rewriting from scratch. And using PROGMEM versions, since I think I was getting memory overflows.
* Update polling rate on all keebs
* Fix planck ez layout config
* Remove macros from Viterbi
* Fix my Tap Dance issues after I broke them
* Cleanup and organization of userspace documentation
As well as some additional cleanup of functions due to review of documentation.
* Enable Tapdance on Glow and remove more animations
* Revert to Eager PR debouncing
* Add better check for startup animation
* Move where RGB Matrix defines are listed
* Limit RGB Matrix max val
* Update keyboard for Iris Rev 3 conflicts
* Enable encoder support on planck ez
* Remove is_master check from corne\'s OLED code
* Overhaul OLED screens for my Corne
* One last removal
* Show RGB valu On both sides
* Updates for OLED display info
* Fix compile issues for rgb config
* Disabled Space Cadet for all drashna keymaps
* Fix OLED Screen configs
* Minor OLED Tweaks
* Revert some Iris changes
* Fix song include
* Handle MAKE macro for the Corne boards better
* Add super hacky-hack for eeconfig initialization
* Add audio support for Fractal since Elite Cs support it
* Add defines for keycode steps
* Add White layout
* Update Corne RGB info
* Add fun effects to layer indication for RGB Matrix enabled boards
* Use proper define for product name detection
* Update formatting
* Use custom timeout mechanism for OLED timeout
* Fix up OLED screen HSV code for new HSV structure
* Better handle turning off RGB Matrix when sleeping
* Disable MultiSplash Animation
* Change Iris back to using serial
* Why was RGB disabled?!?!?!
* Limit val in rgb_matrix_layer_helper function
* Remove EECONFIG setting for RGB matrix
* Enable Mousekeys on Corne Keyboard by default
For Tessachka and Configurator support
* ENable for default image too
* Remove most of rules.mk for default keymap
* make sure rgblight is enabled by default
from default keymap
* Add vlukash CrKbd keymap to support trackpad adapter.
The trackpad adapter uses Elite-C board that has five extra pins.
Also SPI pins are taken for trackpad, keymap config updates column data
pins for matrix scan.
* Update vlukash keymap
* Enable pointing devide, configure mouse BTN1
* Set TAPPING_TERM to 300
* Add support for the BlackBerry 8520 trackpad
* Add vlukash keymap for master-right no-trackpad version
* Remap backspace
* Set EXTRAKEY_ENABLE = yes
* Update thumb keys mappings
* Set bootloader to atmel-dfu
* Sync keymap
* Add scrolling support
* Make debug LEDS conditional
* Add support for both flex and no-flex PCBs
* Add readme and rename root folders
* Update readme file with blog link
* Fix readme file formatting
* Remove ADJUST keycode, code cleanup.
* Add Win key to the keymap.
* Initial conversion of the rgb_led struct
* Converting last keyboard & updating effects to take advantage of the new structure
* New struct should not be const
* Updated docs
* Changing define ___ for no led to NO_LED
* Missed converting some keymap usages of the old struct layout
* Disable a bunch of reactive modes
* Enable rgb matrix for Corne Keyboard
* Convert CRKBD to rgb matrix
* Add Gergo keyboard layout
* Make Diablo 3 tap dance better
* Add basic support for Planck EZ
* Fix RGB Matrix stuff
* Fix keycodes for Planck EZ
* Update CRKBD OLED stuff
* Fix typo for sleep on ergodox glow
* Improve my gergo layout
* Scrolling OLED key logger!
* Change gergo layout
* Hnadle unicode keycodes if unicode is disabled
* Disable COMMAND/CONSOLE for gergo
* Fix right side control
* Re-enable LTO for all platforms
Since I got updated arm gcc binaries that no longer error out on lto
* Update formatting to match newer community standards
Poor 2 space
* Re-alight startup animation to use new HUE range
* Streamline gitlab ci scripts
* Disabled Space Cadet
* Add support for breathing table
* Enable new LTO Option
And clean up defines that will now be repeatitive
* Remove vscode settings
* Additional formatting cleanup of config.h files
* Start to standardize macro timer
* Update Fractal layout
Specifically, limit the RGB Lighting, since it's too many for the power, and only have the KITT annimation on the front
* Update Iris keymap to use I2C for transport
* Remove TAP_CODE_DELAY from keyboard in favor of global setting
* Remove Woodpad
Since it\'s no longer in my possession
* Only enable LTO on AVR boards
* Run matrix_scans while doing startup light
* Run matrix_scan to get split keyboard code synced properly
* Fix rgb mode
* Remove custom debouncing settings
* Make RGB Light Startup Animation optional
* Fix opt def
* Remove extra tap code delay value
* Fix references to keebio boards
* Add support for LP Iris keyboard
* Add backlight code
* Make startup animation optional
* Update gitlab ci script
* Remove port declaration
* Revert avrgcc changes to gitlab ci file
* Don't re-set mods
* Remove MACRO_TIMER define
* Add custom name for crkbd
* Add name for Prime M pad
* Add names for ortho 4x12 boards
* Add some additional handling for rgb init
* Change thumb clusters on ergodox
* Switch Orthodox to I2C
* Fix Space in ergodox keymap
* Use OSL for ergodox layout
* Ugh, can't find a good layout
* Fix typo
* Fix up animation startup
* Cries in AVR
* Fix makefiles for ergodox ez boards
* Add support for "secret songs" in my userspace
* Reset debounce to 5ms for Ergodox EZ
* Fix gitlab CI yaml file
* More crying in AVR
* Cannot use rgb light and rgb matrix at the same time due to the WS2812 rgb matrix PR until the "Coexistance" PR is merged
* Update ODox for split common and i2c
* Add split config
* Impement Split code
* Add support for xscorpion OLED code
* Add OLED display config
* Fix OLED screen font
* Get OLED set up in vertical mode
* Remove old OLED code
* add per key support for crkbd
* Fix split changes
* RGB Tweeaks
* More OLED tweaks
* Fix rotation stuff
* Fix more OLED stuff
* Remove custom Debounce from Ergodox layout since it's no longer needed
* Reduce CRKBD firmware size by reducing layer numbers
* Update layer output code based on mtei's suggestion/code
* Fix spacing
* Revert "Update layer output code based on mtei's suggestion/code"
This reverts commit 036d347db3.
Unfortunately, because this is NOT in the keymap itself, the layer macros aren't accessible and will error on commit
* Add comment for future person
* Use correct functions for dip switch code
* Some planck cleanup
* Hopefully fix RGB Sleeping with RGB Matrix
* Add rgbmatrix extern
* Add numpad 5x6 layout
* RGB Tweaks
* Add RGB startup animation
* Minor RGB Fixes
* Turn off RBG on planck
* Enable separate storage of EEPROM
* Update Macro pad
* Add BJohnson Keymap and minor darshna tweaks
* Clean up rgb and other code for new numpad
* Remove clicky hachy thing
* Update my code to use built in MOD_MASK defines
* Fix up modifier calls
* Tweak to KC_MAKE
* Tweak to KC_MAKE
* Add Semi-colon to numpad
* Preprocess out rgb matrix stuff if not enabled
* Formatting of KC_MAKE
* Add stuff for matrix and light rgb coexistance
* Fix bad spelling
* Change where layer indication shows based on rgblight status
* Force set mods in KC_MAKE
* Optimize CRKBD
- flags for the linker
- added INSERT key as I kinda use it for work fairly often
- turned on more things in rules.mk since I recovered space via linker
flags and whatnot
* moved some stuff around on my iris layout, but don't expect a lot of changes in the future
* good working setup
* [keymap] some mods to my (omgvee) Helidox keymap
* Add default value for IS_COMMAND for COMMAND feature
* Cleanup and consistency
* Update Templates to reflect change
* Fix IS_COMMAND in template
* Fix IS_COMMAND define
* Use consistent IS_COMMAND block in templates
* Remove unnecessary `#undef IS_COMMAND` directives
* Fix compile issue on orthodox
* Reomve IS_COMMAND option for newer boards
* Remove all existing definitions of IS_COMMAND if they use default LSHIFT and RSHIFT setting
* Remove a couple of additional IS_COMMAND defines
* Remove remaining redundant IS_COMMAND definitions
* Remove #undef IS_COMMAND from orthodox:drashna and whitefox:konstantin
* Remove multiple empty lines in modified config.h files
* Update additional boards
* Reomve IS_COMMAND from newer boards
* Update Alice keyboard
* Remove IS_COMMAND from additional boards
Jan 24th edition
* Make CRKBD keylogger output actually show tap keys
* check MT/LT for twinkling
* Add ortho 5x12 support for fractal keyboard
* Use newer interface for setting pins/ports
* Remove custom unicode methods
* Reomve unicode input info
* Odd rules issue
* Redefine REST note to be more pleasing
* Properly disable PM LEDs with GPIO commands
* Update gitlab CI yaml file
* Remove extra mod tap check
* Remove initial state on ergodox glow
* Rev6 Cleanup
* Fix KC_MAKE macro
* Update GitLab CI yaml file
* More GitLab CI changes
* One final GitLab CI change
* Remove unneeded unicode support
* Optimize KC_MAKE
* Fix reversed bool check in layer_state_set
* Add Quefrency 65 for a friend
* Add Ergodox EZ Glow keymap
* Add RGB Matrix Code
* Further changes to rgb matrix ErgoDox EZ
* Update bjohnson keymaps
* Fix CRKBD display
* Overhaul to corne keyboard
* Narrow scope for keylogger
* Minor layout tweaks to Corne Keyboard
* additional CRKBD tweaks
* Minor tweaks to CRKBD
* Add all characters for keylogger
* Ergodox EZ Glow overhaul
* Fix Ergodox EZ Glow layer colors
* Increase Tapping Term for Corne Keyboard
* Fix unicode-ish
* Revert some changes
* Add layer specific lighting effects
* Some minor tweaks to ergodox glow config
* revert changes to ergodox files
* Update Glow readme
* Add more tapping term defines
* Fix changes
* Fix ergodox keymap
* Hopefully fix sleeping
* Disable layer indications if rgb matrix is disabled
* Add support for sleeping and rgb layer change toggle to ergodox ez glow
* Make RGB Layer Indication Great Again
* Make Unicode Great Again
* Remove placeholder define
Co-Authored-By: drashna <drashna@live.com>
* Remove placeholder define
Co-Authored-By: drashna <drashna@live.com>
* Remove old EEPROM Reset keycode
* fix about screen off timer
* Fix Up ScreenOffInterval exceeded uint16_t
* Fix Up never waking up once screen off if in case of matrix are not dirty.
* Revert "fix about screen off timer"
This reverts commit 3d175f2340.
* Fix up screen off timer of crkbd
* Fix Up ScreenOffInterval exceeded uint16_t
* Fix Up never waking up once screen off if in case of matrix are not dirty.
* Fix up screen off timer of helix
* Fix Up ScreenOffInterval exceeded uint16_t
* Fix Up never waking up once screen off if in case of matrix are not dirty
* Revert "Fix up screen off timer of helix"
This reverts commit f0efb82443.
* Improve internal processing of process_record_kb()
* Use the return value of process_record_gfx()
* Fix a indent
Fix a indent
* Fix up userspace after feature merges
* Add new macros for keyboard layouts
* Keep new layouts in keymap for easy reference
* Cleanup layouts
* Fix CRKBD wrappers
* Fix up comments
* Fix spacing in orthodox base layer
* ergodox related cleanup
* Make KC_MAKE only flash when holding shift
* Add option to fast compile boards
* Clean up rgb modes to save space
* Re-enable Swap Hands on my Iris
* Enabled unicode support and send_unicode function
* Unicode cleanup
* More unicode tweaking
* Update EEPROM stuff
* Account for keyboard macros
* Switch Equal to Plus on Ergodox
* more tweaks
* Minor Unicode tweaks
* Correct matrix printing for keylogger
* Fix unicode functions
* Fix unicode mode set since it actually uses EEPROM
* Re-add DISABLE_LEADER
* Ergodox is easier to hit the tapping term, fix that
* Fix stupid type on unicode mode check
* Preliminary CRKBD/HeliDox support
* Fixes to Helidox
* Cleanup userspace from old merge stuff
* Remove CCCV sounds
* Make Mode NOEEPROM Again
* Crkbd: move I2C and Serial defines to keyboard's config.h
per @drashna on Discord
* Crkbd: remove misleading comment re: I2C and Serial
USE_I2C and USE_SERIAL are usually a "one or the other"-type deal, but this keyboard uses both.
* Remove chording as it is not documented, not used, and needs work.
* Make Leader Key an optional feature.
* Switch from `PREVENT_STUCK_MODIFIERS` to `STRICT_LAYER_RELEASE`
* Remove `#define PREVENT_STUCK_MODIFIERS` from keymaps.
* improvement of crkbd communication functions (based on helix-keyboard)
* Removed unnecessary code.
* Changed read restriction from #define to #pragma once.
* Changed from sizeof to defined size.
* moved lib folder to crkbdroot.
removed warning of ws2812.d
