mirror of
https://github.com/qmk/qmk_firmware.git
synced 2024-11-23 11:52:59 +00:00
Merge pull request #716 from MajorKoos/master
Add support for JD40 MKII PCB
This commit is contained in:
Jack Humbert
GitHub
commit
fcc2d43943
74
keyboards/jd40/Makefile
Normal file
74
keyboards/jd40/Makefile
Normal file
@ -0,0 +1,74 @@
|
||||
|
||||
|
||||
# MCU name
|
||||
#MCU = at90usb1287
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
||||
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
||||
# CONSOLE_ENABLE ?= yes # Console for debug(+400)
|
||||
# COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
||||
KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
|
||||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
||||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
|
||||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
||||
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
|
||||
# MIDI_ENABLE ?= YES # MIDI controls
|
||||
# UNICODE_ENABLE ?= YES # Unicode
|
||||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
|
||||
RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../Makefile
|
||||
endif
|
||||
|
||||
79
keyboards/jd40/config.h
Normal file
79
keyboards/jd40/config.h
Normal file
@ -0,0 +1,79 @@
|
||||
/*
|
||||
Copyright 2012 Jun Wako <wakojun@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef CONFIG_H
|
||||
#define CONFIG_H
|
||||
|
||||
#include "config_common.h"
|
||||
|
||||
/* USB Device descriptor parameter */
|
||||
#define VENDOR_ID 0xFEED
|
||||
#define PRODUCT_ID 0x6060
|
||||
#define DEVICE_VER 0x0001
|
||||
#define MANUFACTURER geekhack
|
||||
#define PRODUCT jd40v2
|
||||
#define DESCRIPTION t.m.k. keyboard firmware for JD40 MKII
|
||||
|
||||
/* key matrix size */
|
||||
#define MATRIX_ROWS 4
|
||||
#define MATRIX_COLS 12
|
||||
|
||||
/*
|
||||
* Keyboard Matrix Assignments
|
||||
*
|
||||
* Change this to how you wired your keyboard
|
||||
* COLS: AVR pins used for columns, left to right
|
||||
* ROWS: AVR pins used for rows, top to bottom
|
||||
* DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
|
||||
* ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
|
||||
*
|
||||
*/
|
||||
#define MATRIX_ROW_PINS { F0, F1, F5, B4 }
|
||||
#define MATRIX_COL_PINS { F4, D7, B5, B6, C6, C7, D4, D6, D5, D0, D1, D2 }
|
||||
#define UNUSED_PINS
|
||||
|
||||
/* COL2ROW or ROW2COL */
|
||||
#define DIODE_DIRECTION COL2ROW
|
||||
|
||||
/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
|
||||
#define DEBOUNCING_DELAY 5
|
||||
|
||||
/* define if matrix has ghost (lacks anti-ghosting diodes) */
|
||||
//#define MATRIX_HAS_GHOST
|
||||
|
||||
/* number of backlight levels */
|
||||
#define BACKLIGHT_LEVELS 3
|
||||
|
||||
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
|
||||
#define LOCKING_SUPPORT_ENABLE
|
||||
/* Locking resynchronize hack */
|
||||
#define LOCKING_RESYNC_ENABLE
|
||||
|
||||
|
||||
/* key combination for magic key command */
|
||||
#define IS_COMMAND() ( \
|
||||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
|
||||
)
|
||||
|
||||
#define RGB_DI_PIN D3
|
||||
#define RGBLIGHT_TIMER
|
||||
#define RGBLED_NUM 12 // Number of LEDs
|
||||
#define RGBLIGHT_HUE_STEP 8
|
||||
#define RGBLIGHT_SAT_STEP 8
|
||||
#define RGBLIGHT_VAL_STEP 8
|
||||
|
||||
#endif
|
||||
26
keyboards/jd40/jd40.c
Normal file
26
keyboards/jd40/jd40.c
Normal file
@ -0,0 +1,26 @@
|
||||
#include "jd40.h"
|
||||
|
||||
void led_set_kb(uint8_t usb_led) {
|
||||
// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
|
||||
|
||||
|
||||
// if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
|
||||
// gh60_caps_led_on();
|
||||
// } else {
|
||||
// gh60_caps_led_off();
|
||||
// }
|
||||
|
||||
// if (usb_led & (1<<USB_LED_NUM_LOCK)) {
|
||||
// gh60_esc_led_on();
|
||||
// } else {
|
||||
// gh60_esc_led_off();
|
||||
// }
|
||||
|
||||
// if (usb_led & (1<<USB_LED_SCROLL_LOCK)) {
|
||||
// gh60_fn_led_on();
|
||||
// } else {
|
||||
// gh60_fn_led_off();
|
||||
// }
|
||||
|
||||
led_set_user(usb_led);
|
||||
}
|
||||
45
keyboards/jd40/jd40.h
Normal file
45
keyboards/jd40/jd40.h
Normal file
@ -0,0 +1,45 @@
|
||||
#ifndef JD40_H
|
||||
#define JD40_H
|
||||
|
||||
#include "quantum.h"
|
||||
#include "led.h"
|
||||
|
||||
/* GH60 LEDs
|
||||
* GPIO pads
|
||||
* 0 F7 WASD LEDs
|
||||
* 1 F6 ESC LED
|
||||
* 2 F5 FN LED
|
||||
* 3 F4 POKER Arrow LEDs
|
||||
* B2 Capslock LED
|
||||
* B0 not connected
|
||||
*/
|
||||
|
||||
/*
|
||||
inline void gh60_caps_led_on(void) { DDRB |= (1<<2); PORTB &= ~(1<<2); }
|
||||
inline void gh60_poker_leds_on(void) { DDRF |= (1<<4); PORTF &= ~(1<<4); }
|
||||
inline void gh60_fn_led_on(void) { DDRF |= (1<<5); PORTF &= ~(1<<5); }
|
||||
inline void gh60_esc_led_on(void) { DDRF |= (1<<6); PORTF &= ~(1<<6); }
|
||||
inline void gh60_wasd_leds_on(void) { DDRF |= (1<<7); PORTF &= ~(1<<7); }
|
||||
|
||||
inline void gh60_caps_led_off(void) { DDRB &= ~(1<<2); PORTB &= ~(1<<2); }
|
||||
inline void gh60_poker_leds_off(void) { DDRF &= ~(1<<4); PORTF &= ~(1<<4); }
|
||||
inline void gh60_fn_led_off(void) { DDRF &= ~(1<<5); PORTF &= ~(1<<5); }
|
||||
inline void gh60_esc_led_off(void) { DDRF &= ~(1<<6); PORTF &= ~(1<<6); }
|
||||
inline void gh60_wasd_leds_off(void) { DDRF &= ~(1<<7); PORTF &= ~(1<<7); }
|
||||
*/
|
||||
|
||||
/* JD40 MKII keymap definition macro
|
||||
*/
|
||||
#define KEYMAP( \
|
||||
K01, K02, K03, K04, K05, K06, K07, K08, K09, K10, K11, K12, \
|
||||
K13, K14, K15, K16, K17, K18, K19, K20, K21, K22, K23, \
|
||||
K24, K25, K26, K27, K28, K29, K30, K31, K32, K33, K34, \
|
||||
K35, K36, K37, K38, K39, K40, K41, K42, K43, K44 \
|
||||
) { \
|
||||
{ KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, KC_##K08, KC_##K09, KC_##K10, KC_##K11, KC_##K12 }, \
|
||||
{ KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17, KC_##K18, KC_##K19, KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_NO }, \
|
||||
{ KC_##K24, KC_##K25, KC_##K26, KC_##K27, KC_##K28, KC_##K29, KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_NO }, \
|
||||
{ KC_##K35, KC_##K36, KC_##K37, KC_##K38, KC_##K39, KC_NO, KC_##K40, KC_##K41, KC_##K42, KC_##K43, KC_##K44, KC_NO } \
|
||||
}
|
||||
|
||||
#endif
|
||||
164
keyboards/jd40/keymaps/default/keymap.c
Normal file
164
keyboards/jd40/keymaps/default/keymap.c
Normal file
@ -0,0 +1,164 @@
|
||||
#include "jd40.h"
|
||||
#include "action_layer.h"
|
||||
|
||||
#define _BL 0
|
||||
#define _AL 1
|
||||
#define _FL 2
|
||||
#define _UL 3
|
||||
|
||||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
|
||||
[_BL] = KEYMAP(
|
||||
F12, Q, W, E, R, T, Y, U, I, O, P, BSPC,
|
||||
TAB, A, S, D, F, G, H, J, K, L, ENT,
|
||||
LSFT, Z, X, C, V, B, N, M, COMM, UP, DOT,
|
||||
LCTL, LGUI, LALT, FN0, SPC, SPC, FN0, LEFT, DOWN, RIGHT ),
|
||||
|
||||
[_AL] = KEYMAP(
|
||||
GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, DEL,
|
||||
CAPS, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0,
|
||||
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, SCLN, PGUP, QUOT,
|
||||
TRNS, TRNS, TRNS, TRNS, FN3, FN3, TRNS, HOME, PGDN, END ),
|
||||
|
||||
[_FL] = KEYMAP(
|
||||
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS,
|
||||
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS,
|
||||
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS,
|
||||
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS ),
|
||||
|
||||
[_UL] = KEYMAP(
|
||||
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS,
|
||||
TRNS, FN4, FN5, FN11, FN10, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS,
|
||||
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS,
|
||||
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS ),
|
||||
};
|
||||
|
||||
enum function_id {
|
||||
RGBLED_TOGGLE,
|
||||
RGBLED_STEP_MODE,
|
||||
RGBLED_INCREASE_HUE,
|
||||
RGBLED_DECREASE_HUE,
|
||||
RGBLED_INCREASE_SAT,
|
||||
RGBLED_DECREASE_SAT,
|
||||
RGBLED_INCREASE_VAL,
|
||||
RGBLED_DECREASE_VAL,
|
||||
SHIFT_ESC,
|
||||
};
|
||||
|
||||
const uint16_t PROGMEM fn_actions[] = {
|
||||
[0] = ACTION_LAYER_MOMENTARY(1), // Momentary Fn overlay
|
||||
[1] = ACTION_LAYER_TOGGLE(2), // Toggle Arrow Layer overlay
|
||||
[2] = ACTION_LAYER_TAP_KEY(2, KC_CAPS), // Tap to toggle caps lock and hold to activate function layer
|
||||
[3] = ACTION_LAYER_TOGGLE(3), // Toggle Underglow Layer overlay
|
||||
[4] = ACTION_FUNCTION(RGBLED_TOGGLE), //Turn on/off underglow
|
||||
[5] = ACTION_FUNCTION(RGBLED_STEP_MODE), // Change underglow mode
|
||||
[6] = ACTION_FUNCTION(RGBLED_INCREASE_HUE),
|
||||
[7] = ACTION_FUNCTION(RGBLED_DECREASE_HUE),
|
||||
[8] = ACTION_FUNCTION(RGBLED_INCREASE_SAT),
|
||||
[9] = ACTION_FUNCTION(RGBLED_DECREASE_SAT),
|
||||
[10] = ACTION_FUNCTION(RGBLED_INCREASE_VAL),
|
||||
[11] = ACTION_FUNCTION(RGBLED_DECREASE_VAL),
|
||||
[12] = ACTION_FUNCTION(SHIFT_ESC),
|
||||
};
|
||||
|
||||
const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
|
||||
{
|
||||
// MACRODOWN only works in this function
|
||||
switch(id) {
|
||||
case 0:
|
||||
if (record->event.pressed) {
|
||||
register_code(KC_RSFT);
|
||||
} else {
|
||||
unregister_code(KC_RSFT);
|
||||
}
|
||||
break;
|
||||
}
|
||||
return MACRO_NONE;
|
||||
};
|
||||
|
||||
void matrix_scan_user(void) {
|
||||
|
||||
// Layer LED indicators
|
||||
// ESC led on when in function layer, WASD cluster leds enabled when on arrow cluster
|
||||
uint32_t layer = layer_state;
|
||||
if (layer & (1<<1)) {
|
||||
//gh60_wasd_leds_on();
|
||||
} else {
|
||||
//gh60_wasd_leds_off();
|
||||
}
|
||||
|
||||
if (layer & (1<<2)) {
|
||||
//gh60_esc_led_on();
|
||||
} else {
|
||||
//gh60_esc_led_off();
|
||||
}
|
||||
};
|
||||
|
||||
#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT))
|
||||
|
||||
void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) {
|
||||
switch (id) {
|
||||
case RGBLED_TOGGLE:
|
||||
//led operations
|
||||
if (record->event.pressed) {
|
||||
rgblight_toggle();
|
||||
}
|
||||
break;
|
||||
case RGBLED_INCREASE_HUE:
|
||||
if (record->event.pressed) {
|
||||
rgblight_increase_hue();
|
||||
}
|
||||
break;
|
||||
case RGBLED_DECREASE_HUE:
|
||||
if (record->event.pressed) {
|
||||
rgblight_decrease_hue();
|
||||
}
|
||||
break;
|
||||
case RGBLED_INCREASE_SAT:
|
||||
if (record->event.pressed) {
|
||||
rgblight_increase_sat();
|
||||
}
|
||||
break;
|
||||
case RGBLED_DECREASE_SAT:
|
||||
if (record->event.pressed) {
|
||||
rgblight_decrease_sat();
|
||||
}
|
||||
break;
|
||||
case RGBLED_INCREASE_VAL:
|
||||
if (record->event.pressed) {
|
||||
rgblight_increase_val();
|
||||
}
|
||||
break;
|
||||
case RGBLED_DECREASE_VAL:
|
||||
if (record->event.pressed) {
|
||||
rgblight_decrease_val();
|
||||
}
|
||||
break;
|
||||
case RGBLED_STEP_MODE:
|
||||
if (record->event.pressed) {
|
||||
rgblight_step();
|
||||
}
|
||||
break;
|
||||
static uint8_t shift_esc_shift_mask;
|
||||
// Shift + ESC = ~
|
||||
case SHIFT_ESC:
|
||||
shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK;
|
||||
if (record->event.pressed) {
|
||||
if (shift_esc_shift_mask) {
|
||||
add_key(KC_GRV);
|
||||
send_keyboard_report();
|
||||
} else {
|
||||
add_key(KC_ESC);
|
||||
send_keyboard_report();
|
||||
}
|
||||
} else {
|
||||
if (shift_esc_shift_mask) {
|
||||
del_key(KC_GRV);
|
||||
send_keyboard_report();
|
||||
} else {
|
||||
del_key(KC_ESC);
|
||||
send_keyboard_report();
|
||||
}
|
||||
}
|
||||
break;
|
||||
}
|
||||
};
|
||||
17
keyboards/jd40/readme.md
Normal file
17
keyboards/jd40/readme.md
Normal file
@ -0,0 +1,17 @@
|
||||
## jd40 mkii keyboard firmware
|
||||
|
||||
Pins:
|
||||
MATRIX_ROW_PINS { F0, F1, F5, B4 }
|
||||
MATRIX_COL_PINS { F4, D7, B5, B6, C6, C7, D4, D6, D5, D0, D1, D2 }
|
||||
RGB_DI_PIN D3
|
||||
|
||||
======================
|
||||
|
||||
## Quantum MK Firmware
|
||||
|
||||
For the full Quantum feature list, see [the parent readme.md](/readme.md).
|
||||
|
||||
## Building
|
||||
|
||||
Download or clone the whole firmware and navigate to the keyboards/jd40 folder.
|
||||
Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Amtel Flip to program your .hex file.
|
||||
69
keyboards/jd40/rules.mk
Normal file
69
keyboards/jd40/rules.mk
Normal file
@ -0,0 +1,69 @@
|
||||
|
||||
|
||||
# MCU name
|
||||
#MCU = at90usb1287
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
||||
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
||||
# CONSOLE_ENABLE ?= yes # Console for debug(+400)
|
||||
# COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
||||
KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
|
||||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
||||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
|
||||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
||||
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
|
||||
# MIDI_ENABLE ?= YES # MIDI controls
|
||||
# UNICODE_ENABLE ?= YES # Unicode
|
||||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
|
||||
RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow
|
||||
Loading…
Reference in New Issue
Block a user