mirror of
https://github.com/qmk/qmk_firmware.git
synced 2024-12-22 17:39:55 +00:00
56 lines
3.4 KiB
Markdown
56 lines
3.4 KiB
Markdown
|
# Microsoft Sculpt Mobile
|
||
|
|
|
||
|
|
This is a way to take a Microsoft ergonomic bluetooth keyboard, and make it
|
||
|
|
into a hard-wired keyboard running QMK.
|
||
|
|
|
||
|
|
The keyboard is known under several different names:
|
||
|
|
Mobile Bluetooth 5000, Mobile 6000, Sculpt mobile, and Asus rebranded.
|
||
|
|
|
||
|
|
I had a stack of them, since they're cheap on ebay, travel well, and are just ergo enough.
|
||
|
|
|
||
|
|
The ribbon cable is 1mm pitch, which is hard to hand solder. I bought a cheap set of
|
||
|
|
"pitch adapter" boards https://www.amazon.com/Double-Sided-0-4mm-1-0-Adapter-60mmx38mm/dp/B00OK42118
|
||
|
|
|
||
|
|
Cut the original ribbon cable sockets off the bluetooth board using a razor, they're hard to desolder.
|
||
|
|
They're also allow the cable to be inserted on top or bottom.
|
||
|
|
|
||
|
|
If I was going to do it again, I'd make the MCU connection come out the top of the keyboard
|
||
|
|
and avoid the wires dangling out the bottom.
|
||
|
|
|
||
|
|
As I was debugging the matrix, I started to get random failures. In desparation I tried a second MCU,
|
||
|
|
but had the same problems. It turns out that the ribbon cable connections can get worn. Shave a
|
||
|
|
half millimeter off the end of the ribbon cable & the errors go away.
|
||
|
|
|
||
|
|
My method for discovering the matrix was to set up a LAYOUT macro that included all pins.
|
||
|
|
See MATRIX_TESTING_LAYOUT if you need it. Then set up a keymap that has all printable symbols
|
||
|
|
in the first 4 rows. test each key & record output. Then switch the printable symbols to the
|
||
|
|
bottom 4 rows & repeat. This was enough to show the matrix.
|
||
|
|
|
||
|
|
|
||
|
|
The full original keymap for the Sculpt is
|
||
|
|
|
||
|
|
| | A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R |
|
||
|
|
|:-:|:--:|:--:|:--:|:---:|:---:|:---:|:----:|:----:|:----:|:-----:|:----:|:------:|:----:|:-----:|:----:|:------:|:----:|:---:|
|
||
|
|
| 0 | b | n | m | , | . | / | | | | Caps | | | | | | | | Fn |
|
||
|
|
| 1 | g | h | " | | | | | | | | Vol+ | Mute | RCtl | | Vol- | PgDn | LCtl | |
|
||
|
|
| 2 | 7 | 8 | 9 | 0 | Del | | PgUp | | | | | RShift | | | | LShift | | |
|
||
|
|
| 3 | p | [ | ] | \ | | | | | | | RAlt | | | | LAlt | | | |
|
||
|
|
| 4 | y | u | i | o | | | | | | | | | | LGUI | | | | |
|
||
|
|
| 5 | ~ | - | += | j | k | l | ; | 5 | 6 | Bksp | 1 | 2 | 3 | 4 | F4 | F5 | F6 | |
|
||
|
|
| 6 | a | s | d | q | w | e | Up | Left | Down | Right | | | | Space | F1 | F2 | F3 | Tab |
|
||
|
|
| 7 | F7 | F8 | F9 | F10 | F11 | F12 | | f | r | t | z | x | c | | v | Enter | Esc | |
|
||
|
|
|
||
|
|
This works with 18 cols + 8 rows on a Teensy++, or ARM-based Teensy.
|
||
|
|
|
||
|
|
The Astar mini has all pins exposed , so you can do 18x8
|
||
|
|
If you want a speaker, LEDs, etc., you'll need to free up a pin. I recommend joining columns
|
||
|
|
R and L to the same pin.
|
||
|
|
|
||
|
|
Building - add ASTAR=1 to the compile line or leave out for teensy2++
|
||
|
|
|
||
|
|
Make example for this keyboard (after setting up your build environment):
|
||
|
|
|
||
|
|
make handwired/ms_sculpt_mobile:default
|
||
|
|
|
||
|
|
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
|