qmk_firmware/keyboards/helix/rules.mk

76 lines
3.0 KiB
Makefile
Raw Normal View History

Keyboard: Helix serial improvements (#3608) * add change_reciver2sender()/change_sender2reciver() This is a change to improve readability. * txled, rxled off in matrix_init() * add serial_send_packet() / serial_recive_packet() This is a change to reduce object size. * add serial_low() at ISR() top * add __attribute__((always_inline)) to some functions * modify serial_send_packet()/serial_recive_packet() A little, object size reduction. A little, speedup. * add debug code to helix/serial.c * Adjust sampling timing of serial signal being received * add split_scomm.c/split_scomm.h and change serial.c/serial.h serial.c was divided into 2 layers, split_scom.c and serial.c. The upper layer split_scomm.c is called from matrix.c. The lower layer serial.c accesses the hardware. * add split_scomm.c/split_scomm.h into helix/rev1 * reduce object size helix/rev2/matrix.c * remove checksum check, add parity check * force occur parity error for test * parity test ok. remove test code * change some comment & add skip code when buffer_size == 0 * serial.c: multiple types of transaction support Add 4 bits transaction-type field at packet top. Select Transaction Descriptor Table entry by transaction-type. * helix serial master-slave transaction optimize Using multi-type transaction feature of serial.c, communication contents between master slaves were optimized. * add debug code for retry * add comment into each config.h * fix ISR status drop * add a debug macro 'debug_retry_chg()' * reduce led_test size * remove debug code from helix/serial.c and etc. * helix:five_rows change TAPPING_TERM value 140 * Improved compatibility with let's split of serial.c. Finish helix/serial.c improvement. - The difference with the original let's split's serial.c - It's high-speed about 4 times. - Stable bi-directional data transfer. (Helix need master to slave transfer) - serial.h was divided 2 files, serial_config.h and sereial.h - With multiple types of transaction support, communication contents can be optimized. (NEW flexible API) - USE OLD Simple APIs (compatible with let's split serial.c) - files : - serial_config.h -- hardware configuration (need include by config.h) - serial.c/serial.h -- serial communication - USE NEW flexible APIs. (Support multi-type transaction function.) serial.c was divided into 2 layers, split_scom.c and serial.c. The upper layer split_scomm.c is called from matrix.c. The lower layer serial.c accesses the hardware. - files - split_scomm.c -- communication buffer is defined in here. call by matrix.c. - split_scomm.h -- buffer size is defined in here. include by matrix.c, split_util.c - serial_config.h -- hardware configuration (need include by config.h) To use the NEW API, specify #define SERIAL_USE_MULTI_TRANSACTION - serial.c/serial.h -- serial communication lower layer - NEW APIs for serial.c / serial.h (The lower layer) // Soft Serial Transaction Descriptor typedef struct _SSTD_t { uint8_t *status; uint8_t initiator2target_buffer_size; uint8_t *initiator2target_buffer; uint8_t target2initiator_buffer_size; uint8_t *target2initiator_buffer; } SSTD_t; // initiator is transaction start side void soft_serial_initiator_init(SSTD_t *sstd_table); // target is interrupt accept side void soft_serial_target_init(SSTD_t *sstd_table); int soft_serial_transaction(int sstd_index); int soft_serial_get_and_clean_target_status(int sstd_index); - NEW APIs for split_scomm.c / split_scomm.h (The upper layer) move from old serial.c the following buffer and functions serial_slave_buffer[] serial_master_buffer[] void serial_master_init(void) void serial_slave_init(void) int serial_update_buffers(void) define SERIAL_xxxxx_BUFFER_LENGTH move from serial_config.h to split_scomm.h
2018-08-10 15:22:09 +00:00
SRC += i2c.c
SRC += serial.c
SRC += ssd1306.c
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
2019-08-02 03:47:52 +00:00
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# atmega32a bootloadHID
BOOTLOADER = caterina
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = no # Audio control and System control(+450)
CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = no # Commands for debug and configuration
NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
MIDI_ENABLE = no # MIDI controls
AUDIO_ENABLE = no # Audio output on port C6
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
2018-10-22 15:57:37 +00:00
RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
SUBPROJECT_rev1 = no
USE_I2C = yes
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
CUSTOM_MATRIX = yes
DEFAULT_FOLDER = helix/rev2